ENTRY AND START SYSTEM(for Entry Function) SYSTEM DESCRIPTION

VEHICLE BATTERY SAVING FUNCTION

1. When the entry and start system (for Entry Function) is operating, the vehicle performs key detection operations every 0.25 seconds. Therefore, if the vehicle left as is for a long period of time, the battery may become fully depleted. The following controls help reduce the rate at which the battery is depleted.

   1. If the engine is not started for 6 days or more, periodic signal transmission from the electrical key antennas stops. However, the doors can still be unlocked by touching the unlock sensor of a front door outside handle assembly.

   2. If the engine is not started for 15 days or more, the lock and unlock sensors of the front passenger side door outside handle assembly are disabled. Therefore, only the unlock sensor of the front door outside handle assembly of the driver side door can be used to unlock the doors.

   3. If 10 minutes or more elapse while the key is in the detection area (including the vehicle interior), entry and start system control stops operating.

2. To restore operation of the entry and start system, perform any of the following operations.

   1. While carrying the key, touch the lock and unlock sensor of the front door outside handle assembly of the driver side door and perform a door lock or unlock operation.

   2. Lock or unlock the doors with the wireless operation.

   3. Insert the mechanical key into the door key cylinder of the driver side door and lock or unlock the doors.

WIRELESS BUZZER VOLUME ADJUSTMENT FUNCTION (w/ Wireless Buzzer Answer-back)

1. The volume of the wireless buzzer can be changed through the customize function.

   Tip:

   The volume of the following wireless buzzer operations cannot be adjusted.

   • Warning function buzzer operations (w/ Warning Function Buzzer Operations)

   • Customize function buzzer operations

   • Buzzer operations for key diagnostic mode using the intelligent tester

   • Key registration buzzer operations

WARNING FUNCTION

1. Shift lever not in P (power source cut reminder) vehicle exit warning

   1. Situation A: The driver side door is opened and vehicle exit is attempted while the shift lever is not in P.

      Item	Content
      Reason for warning	Prevention of sudden forward movement of vehicle Vehicle theft prevention Vehicle roll-away (vehicle starts moving even when nobody is aboard due to slope, etc.) prevention
      Warning start condition (All conditions are met)	Shift lever is not in P Engine switch is on (ACC) or on (IG) Driver side door is opened Vehicle speed is 0 km/h (0 mph)
      Warning description	Buzzer in combination meter assembly sounds continuously (beep) "Shift to P position when alighting" is displayed on multi-information display in combination meter assembly
      Warning stop condition (Any condition is met)	Shift lever moved to P Engine switch is turned off Driver side door is closed Vehicle is driven

   2. Situation B: Under the conditions specified in situation A, the key is brought out of the vehicle, the driver side door is closed and movement away from the vehicle is attempted.

      Item	Content
      Reason for warning	Prevention of sudden forward movement of vehicle Vehicle theft prevention Vehicle roll-away prevention
      Warning start condition (All conditions are met)	Shift lever is not in P Engine switch is on (ACC) or on (IG) Driver side door is opened and then closed Vehicle speed is 0 km/h (0 mph) Key is not inside vehicle (matching code is not detected in vehicle interior)
      Warning description	Buzzer in combination meter assembly sounds continuously (beep) "Shift to P position when alighting" is displayed on multi-information display in combination meter assembly Wireless buzzer sounds continuously (beep)*
      Warning stop condition (Any condition is met)	Shift lever is moved to P or vehicle is driven: Buzzer stops and only "Key not detected" is displayed on multi-information display Engine switch is turned off: All warnings stop Key is detected inside vehicle (matching code is detected in vehicle interior): Buzzer stops and only "Shift to P position" is displayed on multi-information display

      • *: w/ Warning Function Buzzer Operations

2. Key reminder warning

   1. The driver side door is opened and vehicle exit is attempted while the steering lock is unlocked.

      Item	Content
      Reason for warning	Vehicle theft prevention
      Warning start condition (Any condition is met)	Condition 1: Engine switch is on (ACC) Driver side door is opened Last mode is not operating* Condition 2: Engine switch is off Driver side door is opened Steering lock is unlocked
      Warning description	Buzzer in combination meter assembly sounds once ("pong" sound) "Check steering lock system" is displayed on multi-information display in combination meter assembly
      Warning stop condition (Any condition is met)	Condition 1: Engine switch is turned on (IG) Condition 2: Driver side door is opened Condition 3: Engine switch is turned off Steering lock is locked Condition 4: Last mode is operating*

      • *: For vehicles with last mode.

3. Shift lever in P (power source cut reminder) vehicle exit warning

   1. Situation A: The driver side door is opened and vehicle exit is attempted while the shift lever is in P and the engine switch is not off.

      Item	Content
      Reason for warning	Vehicle theft prevention
      Warning start condition (All conditions are met)	Shift lever is in P Engine switch is on (ACC) or on (IG) Driver side door is opened and then closed Key is not inside vehicle (matching code is not detected in vehicle interior) Vehicle speed is 0 km/h (0 mph)
      Warning description	Buzzer in combination meter assembly sounds once ("pong" sound) "Key not detected" is displayed on multi-information display in combination meter assembly Wireless buzzer sounds 3 times (short beeps)*
      Warning stop condition (Either condition is met)	Engine switch is turned off Key is detected inside vehicle (matching code is detected in vehicle interior)

      • *: w/ Warning Function Buzzer Operations

   2. Situation B: Under the conditions specified in situation A, the doors are closed and an entry lock operation is attempted.

      Item	Content
      Reason for warning	Vehicle theft prevention
      Warning start condition (All conditions are met)	Shift lever is in P Engine switch is on (ACC) or on (IG) All doors are closed Key is outside vehicle (matching code is detected outside of vehicle) Key is not inside vehicle (matching code is not detected in vehicle interior) Entry lock operation is performed while carrying key
      Warning description	Wireless buzzer sounds for 5 seconds (continuous beep)* Buzzer in combination meter assembly sounds once ("pong" sound) "Turn power off", "Key not detected" is displayed on multi-information display in combination meter assembly for 60 seconds
      Warning stop condition (Any condition is met)	Engine switch is turned off Shift lever is moved to any position other than P Vehicle is driven Key is detected inside vehicle (matching code is detected in vehicle interior) Any door is opened (only buzzer stops) 5 seconds elapse after warning starts (only buzzer stops)

      • *: w/ Warning Function Buzzer Operations

4. Passenger has brought key out of vehicle warning

   1. Any door other than the driver side door is opened and vehicle exit is attempted while carrying the key.

      Item	Content
      Reason for warning	Prevention of engine being unable to be restarted
      Warning start condition (All conditions are met)	Engine switch is on (ACC) or on (IG) Any door other than driver side door is opened and then closed Vehicle speed is 0 km/h (0 mph) Key is not inside vehicle or key battery is fully depleted (matching code is not detected in vehicle interior)
      Warning description	Buzzer in combination meter assembly sounds once ("pong" sound) "Key not detected" is displayed on multi-information display in combination meter assembly Wireless buzzer sounds 3 times (short beeps)*
      Warning stop condition (Either condition is met)	Engine switch is turned off Key is detected inside vehicle (matching code is detected in vehicle interior)

      • *: w/ Warning Function Buzzer Operations

5. Starting to drive without key warning

   1. The driver starts driving while they key is not in the vehicle.

      Item	Content
      Reason for warning	Prevention of engine being unable to be restarted
      Warning start condition	Warning due to key being brought out of vehicle is operating and vehicle speed is more than 0 km/h (0 mph) (first time only)
      Warning description	Buzzer in combination meter assembly sounds once ("pong" sound) "Key not detected" is displayed on multi-information display in combination meter assembly
      Warning stop condition (Either condition is met)	Engine switch is turned off Key is detected inside vehicle (matching code is detected in vehicle interior)

6. Key is not within detection area warning

   1. An attempt is made to turn the engine switch on (ACC) or on (IG) or to start the engine while the key cannot be detected inside the vehicle or is not operating properly.

      Item	Content
      Reason for warning	User confusion prevention
      Warning start condition (Both conditions are met)	Key is not inside vehicle or key battery is fully depleted (matching code is not detected in vehicle interior) Engine switch is on (ACC) or on (IG)
      Warning description	Buzzer in combination meter assembly sounds once ("pong" sound) "Key not detected" is displayed on multi-information display in combination meter assembly
      Warning stop condition (Either condition is met)	15 seconds elapse after warning starts Key is detected inside vehicle (matching code is detected in vehicle interior)

7. Key left inside vehicle warning

   1. An entry lock operation is attempted while the key is inside the vehicle.

      Item	Content
      Reason for warning	Vehicle theft prevention
      Warning start condition (All conditions are met)	Engine switch is on (ACC) or on (IG) All doors are closed Any door is unlocked Key is inside vehicle (matching code is detected in vehicle interior) and entry lock operation is performed
      Warning description	Buzzer in combination meter assembly sounds once ("pong" sound) Wireless buzzer sounds for 5 seconds (continuous beep)* "Key detected in vehicle" is displayed on multi-information display in combination meter assembly for 60 seconds
      Warning stop condition (Any condition is met)	Engine switch is turned on (ACC) or on (IG) Any door is opened (only buzzer stops) Key is detected outside vehicle (matching code is detected outside of vehicle) and entry lock operation is performed

      • *: w/ Warning Function Buzzer Operations

8. Door ajar entry lock warning

   1. An entry lock operation is attempted while any door is ajar.

      Item	Content
      Reason for warning	Vehicle theft prevention
      Warning start condition (All conditions are met)	Engine switch is off Any door is ajar other than door for which entry lock operation is performed Entry lock operation is performed while carrying key Key is outside vehicle (matching code is detected outside of vehicle)
      Warning description	Wireless buzzer sounds for 5 seconds (continuous beep)*
      Warning stop condition (Any condition is met)	Engine switch is turned on (ACC) or on (IG) All doors are closed Wireless unlock operation is performed Entry unlock operation is performed 5 seconds elapse after warning starts

      • *: w/ Warning Function Buzzer Operations

9. Glass hatch key lock-in prevention warning

   1. The glass hatch is closed while the key is inside the vehicle.

      Item	Content
      Reason for warning	Vehicle theft prevention
      Warning start condition (All conditions are met)	Vehicle speed is 0 km/h (0 mph) Entry glass hatch open function is enabled All doors are closed and locked Key is inside vehicle and glass hatch is closed
      Warning description	Wireless buzzer sounds for 5 seconds (continuous beep)*
      Warning stop condition (Any condition is met)	Vehicle is driven Glass hatch is opened 5 seconds elapse after warning starts

      • *: w/ Warning Function Buzzer Operations

10. Key lock-in prevention function

    1. The key is locked in the vehicle.

       Item	Content
       Reason for warning	Vehicle theft prevention
       Warning start condition (Either condition is met)	Condition 1: Keyless lock operation*1 is performed Key is inside vehicle (matching code is detected in vehicle interior) Condition 2: Engine switch is off All doors are closed Lock operation other than entry lock operation is performed Key is inside vehicle (matching code is detected in vehicle interior)
       Warning description	Wireless buzzer sounds for 10 seconds (continuous beep)*2 Buzzer in combination meter assembly sounds once ("pong" sound) "Key detected in vehicle" is displayed on multi-information display in combination meter assembly for 60 seconds
       Warning stop condition (Any condition is met)	Engine switch is turned on (ACC) or on (IG) 5 seconds elapse after warning starts (only buzzer stops) 60 seconds elapse after warning starts Vehicle is driven Lock operation is performed

       • *1: A keyless lock operation is when a door is locked by operating the door lock knob of an open door, and then closing the door while pulling the front door outside handle assembly.

       • *2: w/ Warning Function Buzzer Operations

11. Key battery low warning

    1. The vehicle is driven while the key battery is almost depleted.

       Item	Content
       Reason for warning	Helpful function
       Warning start condition (Both conditions are met)	Engine switch is on (IG) for 20 minutes or more and then turned off Key battery is almost depleted
       Warning description	Buzzer in combination meter assembly sounds once ("pong" sound) "Key battery low" is displayed on multi-information display in combination meter assembly for 15 seconds

12. Engine starting support

    1. An attempt is made to start the engine by holding the key against the engine switch while the key battery is fully depleted.

       Item	Content
       Reason for warning	Helpful function
       Warning start condition (All conditions are met)	Engine immobiliser is set Key is not inside vehicle (matching code is not detected in vehicle interior) Unlock operation is performed with mechanical key or 2 consecutive attempts to turn engine switch on (IG) are made (matching code is not detected in vehicle interior)
       Warning description	Buzzer in combination meter assembly sounds once ("pong" sound) "Depress brake pedal touch engine switch with key" is displayed on multi-information display in combination meter assembly for 60 seconds
       Warning stop condition (Any condition is met)	60 seconds elapse after warning starts Key is detected inside vehicle (matching code is detected in vehicle interior or near engine switch) 30 seconds elapse after any door is opened and closed

    2. The system judges that the driver does not understand how to start the engine.

       Item	Content
       Reason for warning	Helpful function
       Warning start condition (Both conditions are met)	Engine switch is off and driver side door is opened Power source mode is changed from off to on (ACC) 2 times or more while brake pedal is not depressed
       Warning description	Buzzer in combination meter assembly sounds once ("pong" sound) "Depress brake pedal, and push engine switch to start" is displayed on multi-information display in combination meter assembly for 10 seconds
       Warning stop condition (Any condition is met)	10 seconds elapse after warning starts Engine switch is turned off Engine switch is turned on (IG)

    3. An attempt is made to start the engine while the shift lever is in a position that does not permit the engine to be started.

       Item	Content
       Reason for warning	Helpful function
       Warning start condition (All conditions are met)	Shift lever is not in P or N Engine is not running Vehicle is not being driven Starter motor is not operating 0.5 seconds or more have elapsed after engine switch is turned on (IG)
       Warning description	Buzzer in combination meter assembly sounds once ("pong" sound) "Shift to P position to start" is displayed on multi-information display in combination meter assembly
       Warning stop condition (Any condition is met)	Power source mode is changed to mode other than on (IG) Engine is started Vehicle is driven Shift lever is moved to P or N

13. Power source off operation advice

    1. An attempt is made to turn the engine switch off while the shift lever is not in P or N.

       Item	Content
       Reason for warning	Helpful function
       Warning start condition (Any condition is met)	Shift lever is not in P or N Engine switch is turned on (ACC) while engine switch is on (IG) or engine is running
       Warning description	Buzzer in combination meter assembly sounds once ("pong" sound) "Shift to P range and push engine switch to turn power off" is displayed on multi-information display in combination meter assembly
       Warning stop condition (Any condition is met)	Shift lever is moved to P Power source mode is changed to mode other than on (ACC)