ENTRY AND START SYSTEM(for Entry Function) Back Door Entry Unlock Function does not Operate

DESCRIPTION

If the entry unlock function does not operate for the back door only, but the entry lock function operates, the request code is being transmitted properly from the back door. In this case, there may be a problem related to the unlock switch (connection between the back door opener switch assembly and certification ECU (smart key ECU assembly)).

WIRING DIAGRAM

A005D19E20

CAUTION / NOTICE / HINT

Note


  • The entry and start system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the entry and start system (for Entry Function) after confirming that the communication systems are functioning properly.

  • When using the GTS with the power switch off to troubleshoot:

    Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.

  • Check that there are no electrical key transmitter sub-assemblies in the vehicle.

  • Before replacing the certification ECU (smart key ECU assembly), refer to the Service Bulletin.

  • After repair, confirm DTC not reoccur with performing the "DTC Output Confirmation Operation".

PROCEDURE


  1. READ VALUE USING GTS (ENTRY BACK DOOR OPEN FUNCTION)


    1. Connect the GTS to the DLC3.

    2. Turn the power switch on (IG).

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Entry&Start / Data List.

    5. Read the Data List according to the display on the GTS.

      Entry&Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      B-Dr Opening Operation Back door opening operation / Long, Twice, OFF Customization status displayed -
      Result
      Result Proceed to
      Customize setting is Long or Twice. A
      Customize setting is OFF. B

    B

    PERFORM CUSTOMIZE SETTING (Proceed to Customize Parameters) Click here

    A

  2. CHECK POWER DOOR LOCK OPERATION


    1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation Click here.

      OK
      Door locks operate normally.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

    OK

  3. PERFORM ACTIVE TEST USING GTS


    1. Enter the following menus: Body Electrical / Main Body / Active Test.

    2. Perform the Active Test according to the display on the GTS.

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Trunk and Back-Door Open Operate back door lock motor ON or OFF -
      OK
      The back door lock assembly unlatches when ON is selected.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

    OK

  4. READ VALUE USING GTS (UNLOCK SWITCH)


    1. Using the GTS, read the Data List Click here.

      Entry&Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Tr/B Door Unlock SW Back door opener switch (unlock switch) / ON or OFF

      ON: Back door opener switch (unlock switch) pushed

      OFF: Back door opener switch (unlock switch) not pushed

      • Displays whether the back door opener switch (unlock switch) is on or off.

      • Use this Data List item to help determine if there is a switch malfunction when the back door unlock function does not operate.
      OK
      The GTS display changes correctly in response to the operation of the back door opener switch assembly.

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

  5. CHECK HARNESS AND CONNECTOR (BACK DOOR OPENER SWITCH ASSEMBLY - CERTIFICATION ECU)


    1. Disconnect the V4 back door opener switch assembly connector.

    2. Disconnect the L62 certification ECU (smart key ECU assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      V4-3 (UL) - L62-22 (TSW5) Always Below 1 Ω
      V4-2 (E) - Body ground Always Below 1 Ω
      V4-3 (UL) or L62-22 (TSW5) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. INSPECT BACK DOOR OPENER SWITCH ASSEMBLY (UNLOCK SWITCH)


    1. A0059UZE10
      Text in Illustration
      *a

      Component without harness connected

      (Back Door Opener Switch Assembly)

      Remove the back door opener switch assembly Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      3 (UL) - 2 (E) No switch pushed 10 kΩ or higher
      3 (UL) - 2 (E) Unlock switch pushed Below 1 Ω

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

    REPLACE BACK DOOR OPENER SWITCH ASSEMBLY Click here