LIGHTING SYSTEM DATA LIST / ACTIVE TEST
DATA LIST
Tip:Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note:In the following table, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Data List.
Read the Data List according to the display on the GTS.
Body Electrical > Main Body > Data List
Tester Display
Measurement Item
Range
Normal Condition
Diagnostic Note
ACC SW
Ignition switch ACC signal
ON or OFF
ON: Ignition switch ACC
OFF: Ignition switch off
-
IG SW
Ignition switch ON signal
ON or OFF
ON: Ignition switch ON
OFF: Ignition switch off
-
RR Door Courtesy SW
Rear door courtesy light switch assembly RH signal
ON or OFF
ON: Rear door RH open
OFF: Rear door RH closed
-
RL Door Courtesy SW
Rear door courtesy light switch assembly LH signal
ON or OFF
ON: Rear door LH open
OFF: Rear door LH closed
-
Back Door Courtesy SW
Back door courtesy switch signal
ON or OFF
ON: Back door open
OFF: Back door closed
-
FR Door Lock Pos
Front door RH unlock detection switch signal
LOCK or UNLOCK
LOCK: Front door RH locked
UNLOCK: Front door RH unlocked
-
FR Door Courtesy SW
Front door courtesy light switch assembly RH signal
ON or OFF
ON: Front door RH open
OFF: Front door RH closed
-
FL Door Lock Pos
Front door LH unlock detection switch signal
LOCK or UNLOCK
LOCK: Front door LH locked
UNLOCK: Front door LH unlocked
-
FL Door Courtesy SW
Front door courtesy light switch assembly LH signal
ON or OFF
ON: Front door LH open
OFF: Front door LH closed
-
RR-Door Lock Pos SW
Rear door RH unlock detection switch signal
ON or OFF
ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked
-
RL-Door Lock Pos SW
Rear door LH unlock detection switch signal
ON or OFF
ON: Rear door RH or LH unlocked
OFF: Rear door RH and LH locked
-
Interior Light Control
Operation of the illuminated entry system
ON or OFF
Customized value is displayed
for Main Body ECU with 2 Connectors
I/L ON W/Door Key Unlock
Function that lights up the interior lights when the doors are unlocked
ON or OFF
Customized value is displayed
-
Lighting Time
Lighting time of the delay control function (illuminated entry system)
15s, 7.5s or 30s
Customized value is displayed
-
Room Light when Aprchd
Function that lights up the interior lights when a key enters any actuation area
ON or OFF
Customized value is displayed
-
I/L when ACC OFF
Function that lights up the interior lights when the ignition switch is turned from ON or ACC to off
ON or OFF
Customized value is displayed
-
ACTIVE TEST
Tip:Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / (desired system) / Active Test.
Perform the Active Test according to the display on the GTS.
Body Electrical > Main Body > Active Test
Tester Display
Measurement Item
Control Range
Diagnostic Note
Illuminated Entry System
Lights up the lights that are controlled by the illuminated entry system.*1
ON or OFF
-
Relay for Interior Light Auto Cut Function
DOME CUT relay
ON or OFF
ON: DOME CUT relay off (interior lights turn off)
OFF: DOME CUT relay on (interior lights turn on)
When performing this active test, turn on all the interior lights.
*1: Refer to System Description for the lights that are controlled by the illuminated entry system.
Body Electrical > Entry&Start > Active Test
Tester Display
Measurement Item
Control Range
Diagnostic Note
Power/Engine SW Light
Engine switch illumination
ON or OFF
w/ Entry and Start System