FRONT SEAT ASSEMBLY(for Power Seat) REMOVAL

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedures listed below are for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing.

    Click here

    Note


    • After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the battery negative (-) terminal notices before proceeding with work.

      Click here


    • If the front seat airbag assembly LH has deployed, replace the front seat airbag assembly LH, separate type front seatback spring assembly, separate type front seatback pad and separate type front seatback cover with the necessary parts in accordance with the extent of the collision damage.

    • If the front seat cushion airbag assembly RH has deployed, replace the front seat airbag sub-assembly RH, front seat adjuster assembly, separate type front seat cushion pad and separate type front seat cushion cover with the necessary parts in accordance with the extent of the collision damage.

  2. REMOVE FRONT SEAT HEADREST ASSEMBLY


    1. Remove the front seat headrest assembly.

  3. REMOVE FRONT SEAT OUTER TRACK BRACKET COVER LH


    1. Operate the front power seat switch LH (slide switch) to move the seat to the rearmost position.

    2. B008HP7

      Detach the 2 claws to remove the front seat outer track bracket cover LH.

  4. REMOVE FRONT SEAT INNER TRACK BRACKET COVER LH


    1. B008JJ8

      Detach the 2 claws to remove the front seat inner track bracket cover LH.

  5. REMOVE FRONT SEAT REAR OUTER TRACK COVER LH


    1. Operate the front power seat switch LH (slide switch) to move the seat to the foremost position.

    2. B008IGB

      Detach the 2 claws to remove the front seat rear outer track cover LH.

  6. REMOVE FRONT SEAT REAR INNER TRACK COVER LH


    1. B008GZH

      Detach the 2 claws to remove the front seat rear inner track cover LH.

  7. REMOVE FRONT SEAT ASSEMBLY LH


    1. for Driver Side:


      1. Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully retract and tilt up the steering column assembly.

      2. Turn the engine switch off.

    2. B008H48

      Remove the 2 bolts.

    3. Operate the front power seat switch LH (slide switch) to move the seat to the rearmost position.

    4. B008IAL

      Remove the 2 bolts.

    5. Operate the front power seat switch LH (slide switch) to move the seat to the center position.

    6. Operate the front power seat switch LH (reclining switch) to move the seatback to the upright position.

    7. Operate the front power seat switch LH (front vertical switch and rear lifter switch) to move the seat to the highest position.

    8. Disconnect the cable from the battery negative (-) terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the battery negative (-) terminal to disable the SRS system.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    9. B008JEV

      for Driver Side:


      1. Disconnect the 2 connectors.

      2. Detach the 2 clamps to disconnect the wire harness.

      3. B008I6V

        Disconnect the connector of the front seat airbag assembly LH.


        1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

          B008JMMC07
          *1 White Housing Lock *2 Yellow CPA

        2. Push down the white housing lock again and disconnect the connector.

          Note

          Do not push down the part (A) shown in the illustration when disconnecting the connector.

    10. B008GTL

      for Passenger Side:


      1. Disconnect the 2 connectors.

      2. Detach the 2 clamps to disconnect the wire harness.

      3. B008IX1C01
        B008IUL Front Seat Airbag Assembly RH Connector
        B008H52 Front Seat Cushion Airbag Assembly RH Connector

        Disconnect the connector of the front seat airbag assembly RH.


        1. Push down the white housing lock and slide the yellow CPA. (At this time, the connector cannot be disconnected yet.)

          B008JMMC07
          *1 White Housing Lock *2 Yellow CPA

        2. Push down the white housing lock again and disconnect the connector.

          Note

          Do not push down the part (A) shown in the illustration when disconnecting the connector.

      4. Disconnect the connector of the front seat cushion airbag assembly RH.

        Place a finger on the slider, slide the slider to release the lock, and then disconnect the front seat side airbag connector.

        B008ILDC17
        *1 Slider - -

    11. Remove the front seat assembly LH from the vehicle.

      Note


      • 2 or more people are required when carrying the front seat assembly out of the vehicle.

      • Be careful not to damage the vehicle body.

      Tech Tips

      for Driver Side:

      When removing the front seat assembly from the vehicle, pass it through under the steering wheel.