ENGINE UNIT COMPONENTS
ILLUSTRATION
*A |
Type A |
*B |
Type B |
*1 |
FUEL DELIVERY PIPE SUB-ASSEMBLY |
*2 |
FUEL INJECTOR ASSEMBLY |
*3 |
FUEL TUBE SUB-ASSEMBLY |
*4 |
THERMOSTAT |
*5 |
VACUUM SURGE TANK |
*6 |
WATER INLET |
*7 |
GASKET |
*8 |
NO. 1 DELIVERY PIPE SPACER |
*9 |
O-RING |
*10 |
INJECTOR VIBRATION INSULATOR |
*11 |
NO. 2 FUEL PIPE CLAMP |
- |
- |
 |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
ILLUSTRATION
*A |
Type A |
*B |
Type B |
*1 |
EXHAUST MANIFOLD |
*2 |
IGNITION COIL ASSEMBLY |
*3 |
NO. 1 EXHAUST MANIFOLD HEAT INSULATOR |
*4 |
EXHAUST MANIFOLD TO HEAD GASKET |
*5 |
MANIFOLD STAY |
*6 |
DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY |
*a |
Diameter 18 mm (0.709 in.) |
*b |
Diameter 17 mm (0.669 in.) |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
ILLUSTRATION
*1 |
ENGINE OIL LEVEL DIPSTICK GUIDE |
*2 |
INTAKE MANIFOLD |
*3 |
NO. 1 WATER BY-PASS PIPE |
*4 |
NO. 3 WATER BY-PASS HOSE |
*5 |
VENTILATION HOSE |
*6 |
WATER BY-PASS HOSE |
*7 |
WATER INLET HOSE |
*8 |
ENGINE OIL LEVEL DIPSTICK |
*9 |
AIR TUBE |
*10 |
NO. 1 INTAKE MANIFOLD TO HEAD GASKET |
*11 |
INTAKE MANIFOLD STAY |
*12 |
O-RING |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
ILLUSTRATION
*1 |
CAMSHAFT POSITION SENSOR |
*2 |
CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
*3 |
CYLINDER HEAD COVER GASKET |
*4 |
CYLINDER HEAD COVER SUB-ASSEMBLY |
*5 |
ENGINE COVER JOINT |
*6 |
OIL FILLER CAP GASKET |
*7 |
OIL FILLER CAP SUB-ASSEMBLY |
*8 |
SPARK PLUG |
*9 |
SPARK PLUG TUBE GASKET |
*10 |
SEAL WASHER |
*11 |
GASKET |
*12 |
O-RING |
*13 |
BRACKET |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
ILLUSTRATION
*1 |
CRANKSHAFT PULLEY |
*2 |
ENGINE OIL PRESSURE SWITCH ASSEMBLY |
*3 |
NO. 1 CHAIN TENSIONER ASSEMBLY |
*4 |
OIL FILTER CAP ASSEMBLY |
*5 |
TIMING CHAIN COVER OIL SEAL |
*6 |
TIMING CHAIN COVER SUB-ASSEMBLY |
*7 |
WATER INLET HOUSING |
*8 |
ENGINE MOUNTING BRACKET RH |
*9 |
GASKET |
*10 |
OIL FILTER BRACKET |
*11 |
OIL FILTER ELEMENT |
*12 |
O-RING |
*13 |
ENGINE WATER PUMP ASSEMBLY |
*14 |
SEAL WASHER |
*15 |
STUD BOLT |
*16 |
BRACKET |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
 |
MP grease |
★ |
Precoated part |
ILLUSTRATION
*1 |
CHAIN SUB-ASSEMBLY |
*2 |
CHAIN TENSIONER SLIPPER |
*3 |
CRANKSHAFT POSITION SENSOR |
*4 |
CRANKSHAFT TIMING GEAR KEY |
*5 |
CRANKSHAFT TIMING SPROCKET |
*6 |
NO. 1 CHAIN VIBRATION DAMPER |
*7 |
NO. 1 CRANKSHAFT POSITION SENSOR PLATE |
*8 |
NO. 2 CHAIN SUB-ASSEMBLY |
*9 |
NO. 2 CHAIN VIBRATION DAMPER |
*10 |
O-RING |
*11 |
OIL PUMP DRIVE GEAR |
*12 |
OIL PUMP DRIVE SHAFT GEAR |
*13 |
CHAIN DAMPER SPRING |
*14 |
CHAIN TENSIONER PLATE |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
ILLUSTRATION
*1 |
CAMSHAFT |
*2 |
CAMSHAFT BEARING CAP |
*3 |
CAMSHAFT HOUSING SUB-ASSEMBLY |
*4 |
CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
*5 |
CAMSHAFT TIMING GEAR ASSEMBLY |
*6 |
CYLINDER HEAD GASKET |
*7 |
CYLINDER HEAD SUB-ASSEMBLY |
*8 |
ENGINE COOLANT TEMPERATURE SENSOR |
*9 |
NO. 1 CAMSHAFT BEARING |
*10 |
NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
*11 |
NO. 2 CAMSHAFT |
*12 |
NO. 2 CAMSHAFT BEARING |
*13 |
OIL CONTROL VALVE FILTER |
*14 |
VALVE LASH ADJUSTER ASSEMBLY |
*15 |
PLATE WASHER |
*16 |
CYLINDER HEAD SET BOLT |
*17 |
GASKET |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
*T1 |
1st: 49 (500, 36) 2nd: Turn 90° 3rd: Turn 45° |
- |
- |
ILLUSTRATION
*1 |
KNOCK CONTROL SENSOR |
*2 |
NO. 1 GENERATOR BRACKET |
*3 |
NO. 1 TAPER SCREW PLUG |
*4 |
NO. 2 OIL PAN SUB-ASSEMBLY |
*5 |
OIL PAN DRAIN PLUG |
*6 |
OIL PUMP ASSEMBLY |
*7 |
REAR ENGINE OIL SEAL |
*8 |
STIFFENING CRANKCASE ASSEMBLY |
*9 |
PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY) |
*10 |
RING PIN |
*11 |
STUD BOLT |
*12 |
GASKET |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
MP grease |
★ |
Precoated part |