AUTOMATIC TRANSAXLE SYSTEM, Diagnostic DTC:P071011

DTC Code DTC Name
P071011 Transmission Fluid Temperature Sensor "A" Circuit Short To Ground

DESCRIPTION

The ATF temperature sensor converts the automatic transaxle fluid (ATF) temperature into a resistance value for use by the ECM.

B0084QBE10
*1 Resistance
*2 Acceptable Range
*3 Temperature

The ECM applies voltage to the ATF temperature sensor through terminal THO1 of the ECM.

The sensor resistance changes with the ATF temperature. As the temperature rises, the sensor resistance decreases.

One terminal of the sensor is grounded so that the sensor resistance and voltage decrease as the temperature rises.

The ECM calculates the ATF temperature based on the voltage signal.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P071011 Transmission Fluid Temperature Sensor "A" Circuit Short To Ground When the battery voltage is 8 V or more and the engine switch is on (IG), the ATF temperature sensor voltage is less than 0.142 V for 0.5 seconds (1-trip detection logic).

  • Wiring harness connector

  • Short in ATF temperature sensor circuit

  • Transmission wire (ATF temperature sensor)

  • ECM

 Comes on DTC stored

SAE Code:

P0712

MONITOR DESCRIPTION

This DTC indicates a short in the ATF temperature sensor circuit. The ATF temperature sensor converts ATF temperature into an electrical resistance value. Based on the resistance, the ECM determines the ATF temperature, and can detect a short in the ATF temperature sensor circuit. If the resistance value of the ATF temperature sensor is less than 79 Ω*, the ECM interprets this as a malfunction of the ATF temperature sensor or wiring and will illuminate the MIL and store this DTC.

*: 150°C (302°F) or more is indicated regardless of the actual ATF temperature.

Tech Tips

The ATF temperature can be checked on the GTS display.

CONFIRMATION DRIVING PATTERN

Tech Tips

After repairs have been completed, clear the DTCs and then check that the vehicle has returned to normal by performing the following All Readiness check procedure.


  1. Connect the GTS to the DLC3.

  2. Turn the engine switch on (IG) and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the engine switch off and wait for 2 minutes or more.

  5. Turn the engine switch on (IG) and turn the GTS on.

  6. Wait for 3 seconds or more with the engine switch on (IG).

  7. Enter the following menus: Powertrain / Transmission / Utility / All Readiness.

  8. Input the DTC: P071011.

  9. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

WIRING DIAGRAM

B0087YZE07
*1 OIL
*2 ATF Temperature Sensor
*3 Wiring Harness Connector
*4 Transmission Wire

CAUTION / NOTICE / HINT

Note

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click here

Tech Tips

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


  1. DATA LIST

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Warm up the engine.

    2. Turn the engine switch off.

    3. Connect the GTS to the DLC3.

    4. Turn the engine switch on (IG).

    5. Turn the GTS on.

    6. Enter the following menus: Powertrain / Transmission / Data List.

    7. Read the Data List according to the display on the GTS.


      Powertrain > Transmission > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      A/T Oil Temperature No.1 ATF temperature sensor value

      Min.: -40°C (-40°F)

      Max.: 150°C (302°F)

      • Approximately 80°C (176°F): After stall speed test

      • Equal to ambient temperature: When engine is cold

      		 If the value is -40°C (-40°F) or 150°C (302°F), the ATF temperature sensor circuit is open or shorted.

      Powertrain > Transmission > Data List
      Tester Display
      A/T Oil Temperature No.1

      Tech Tips

      If DTC P071011 is output and the GTS indicates 150°C (302°F) or more, there is a short in the circuit.

      Measure the resistance between terminal THO1 (OIL) and body ground.

      Temperature Displayed Malfunction
      -40°C (-40°F) Open circuit
      150°C (302°F) or more Short circuit

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (ATF TEMPERATURE SENSOR CIRCUIT)


    1. Disconnect the C58 ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C58-84 (THO1) - C58-83 (ETHO) Always 79 Ω to 156 kΩ
      C58-84 (THO1) - Body ground and other terminals Always 10 kΩ or higher
      C58-83 (ETHO) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (ECM - WIRING HARNESS CONNECTOR)


    1. Disconnect the C54 wiring harness connector connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      C58-84 (THO1) or C54-13 (OIL) - Body ground and other terminals Always 10 kΩ or higher
      C58-83 (ETHO) or C54-12 (E2) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)


    1. B0084G1C01
      *a

      Component without harness connected

      (Transmission Wire)

      Remove the wiring harness connector.

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A-17 (E2) - A-18 (THO1) Always 79 Ω to 156 kΩ
      A-17 (E2) - Body ground and other terminals Always 10 kΩ or higher
      A-18 (THO1) - Body ground and other terminals Always 10 kΩ or higher

      Tech Tips

      If the resistance is out of the specified range at any of the ATF temperatures shown in the table below, the drivability of the vehicle may decrease.

      ATF Temperature Specified Condition
      10°C (50°F) 5 to 8 kΩ
      25°C (77°F) 2.5 to 4.5 kΩ
      110°C (230°F) 0.22 to 0.28 kΩ
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE WIRING HARNESS CONNECTOR Click here

    NG

    REPLACE TRANSMISSION WIRE (ATF TEMPERATURE SENSOR) Click here