FRONT SEAT ASSEMBLY(for Power Seat) INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedures listed below are for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL FRONT SEAT ASSEMBLY LH


    1. Place the front seat assembly in the cabin.

      Note


      • 2 or more people are required when inserting the front seat assembly into the vehicle.

      • Be careful not to damage the vehicle body.

      Tech Tips

      for Driver Side:

      When placing the front seat assembly into the vehicle, pass it through under the steering wheel.

    2. for Driver Side:


      1. Connect the connector to the front seat airbag assembly under the front seat assembly.


        1. Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

          B008GTSC04
          *1 Yellow CPA - -
          *a Correct *b Incorrect

        2. Hold the sides of the yellow CPA and push in the connector in the direction indicated by the arrow until a click sound is heard to connect the connector.

          Note


          • Be careful not to damage the side airbag connector or wire harness.


          • When connecting the connector, make sure to push it straight in.


          • Do not hold any parts other than the yellow CPA when connecting the connector.


          • If the upper portion of the yellow CPA is held when connecting the connector, the partial connection prevention mechanism will not function due to deformation of the yellow CPA. Therefore, hold the sides of the yellow CPA.

    3. Connect the 2 connectors.

    4. Attach the 2 clamps to connect the wire harness.

    5. for Front Passenger Side:


      1. Connect the connector to the front seat airbag assembly under the front seat assembly.


        1. Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

          B008GTSC04
          *1 Yellow CPA - -
          *a Correct *b Incorrect

        2. Hold the sides of the yellow CPA and push in the connector in the direction indicated by the arrow until a click sound is heard to connect the connector.

          Note


          • Be careful not to damage the side airbag connector or wire harness.


          • When connecting the connector, make sure to push it straight in.


          • Do not hold any parts other than the yellow CPA when connecting the connector.


          • If the upper portion of the yellow CPA is held when connecting the connector, the partial connection prevention mechanism will not function due to deformation of the yellow CPA. Therefore, hold the sides of the yellow CPA.

      2. Connect the connector of the front seat airbag assembly RH.

    6. Connect the 2 connectors.

    7. Attach the 2 clamps to connect the wire harness.

    8. Align the pin of the front seat adjuster assembly with the hole in the vehicle.

    9. Temporarily install the front seat assembly with the 4 bolts.

    10. Connect the cable to the battery negative (-) terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    11. Operate the front power seat switch LH (slide switch) to move the seat to the rearmost position.

    12. B008IALN01

      Tighten the 2 bolts in the order indicated in the illustration.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

    13. Operate the front power seat switch LH (slide switch) to move the seat to the foremost position.

    14. B008H48N01

      Tighten the 2 bolts in the order indicated in the illustration.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  2. INSTALL FRONT SEAT REAR INNER TRACK COVER LH


    1. Attach the 2 claws to install the front seat rear inner track cover LH.

  3. INSTALL FRONT SEAT REAR OUTER TRACK COVER LH


    1. Attach the 2 claws to install the front seat rear outer track cover LH.

  4. INSTALL FRONT SEAT INNER TRACK BRACKET COVER LH


    1. Operate the front power seat switch LH (slide switch) to move the seat to the rearmost position.

    2. Attach the 2 claws to install the front seat inner track bracket cover LH.

  5. INSTALL FRONT SEAT OUTER TRACK BRACKET COVER LH


    1. Attach the 2 claws to install the front seat outer track bracket cover LH.

  6. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. Install the front seat headrest assembly.

  7. CHECK SRS WARNING LIGHT

    Click here

  8. INSPECT FRONT POWER SEAT CONTROL SYSTEM


    1. w/ Memory:

      Click here

    2. w/o Memory:

      Click here

  9. INSPECT CLIMATE CONTROL SEAT SYSTEM (w/ Climate Control Seat System)

    Click here

  10. INSPECT SEAT HEATER SYSTEM (w/ Seat Heater System)

    Click here