FRONT SEAT ASSEMBLY(for Manual Seat) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedures listed below are for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)


    1. Attach the 2 clamps to install the seat heater control sub-assembly LH.

  2. INSTALL SEAT TRACK ADJUSTING HANDLE


    1. B0059R9C01
      *1 Spring

      Attach the 2 springs to install the seat track adjusting handle.

  3. INSTALL FRONT SEAT CUSHION SPRING SUB-ASSEMBLY LH


    1. Attach the 6 hooks to install the front seat cushion spring sub-assembly LH to the front seat adjuster assembly LH.

  4. INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side)

    Click here

  5. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH


    1. B0057XZC01
      *1 Clamp
      *2 Guide

      Attach the clamp and guide to install the front seat cushion edge protector LH.

  6. INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH

    Tech Tips

    Use the same procedure described for the LH side.

  7. INSTALL FRONT LOWER SEAT CUSHION SHIELD LH


    1. B0056Z4

      Attach the clip to install the front lower seat cushion shield LH.

    2. Attach the hook in the direction indicated by the arrow in the illustration.

    3. Install the screw.

  8. INSTALL FRONT LOWER SEAT CUSHION SHIELD RH

    Tech Tips

    Use the same procedure described for the LH side.

  9. INSTALL FRONT SEAT CUSHION AIRBAG ASSEMBLY RH (for Front Passenger Side)

    Click here

  10. INSTALL FRONT SEATBACK SPRING SUB-ASSEMBLY LH


    1. Attach the 2 hooks to install the front seatback spring sub-assembly LH to the front seatback frame sub-assembly LH.

  11. INSTALL FRONT SEATBACK EDGE PROTECTOR


    1. Attach the 2 claws and 4 guides to install the 2 front seatback edge protectors.

  12. INSTALL FRONT NO. 1 SEATBACK HOOK


    1. Install the 2 front No. 1 seatback hooks to the front seatback spring sub-assembly LH.

    2. Attach the 2 claws.

  13. INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY LH


    1. Attach the 4 guides to install the separate type front seatback spring assembly LH to the front seat adjuster assembly LH.

    2. Install the 4 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  14. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH

    Click here

  15. INSTALL SEATBACK FELT


    1. Install the seatback felt to the separate type front seatback spring assembly LH.

  16. INSTALL SEAT COVER WIRE


    1. Install the seat cover wire.

      Tech Tips


      • Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.


      • For wire 1000 mm (3.28 ft.) or less in length, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.


      • Make sure to read the precautions before preparing the wire.

        Click here

      B0059VLN01
      Length
      A 160 mm (6.29 in.) B 150 mm (5.91 in.)
      C 400 mm (1.31 ft.) - -

      Tech Tips

      The dimensions shown in the illustration are the lengths.

      B0058PS

  17. INSTALL SEPARATE TYPE FRONT SEATBACK COVER LH

    Tech Tips


    • When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.

      Click here


    • Align the seam allowance in a single direction as shown in the illustration.

    B005AOMN01

    1. B005ALUC01
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type front seatback cover LH to the separate type front seatback pad LH with 14 new hog rings in the order indicated in the illustration.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.


      1. B0059X8

        Pass the 3 seatback cover brackets through the 3 holes of the separate type front seatback pad LH.

        Note

        After the seatback cover bracket is installed, make sure the seatback cover bracket is not twisted.

  18. INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD


    1. Temporarily install the separate type front seatback cover with pad.

    2. Connect the 3 seatback cover brackets with the 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note


      • For vehicles with a front seat airbag assembly, the separate type front seatback cover with pad must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.


      • Make sure that the strap is not twisted after installing the nut.


      • Install the brackets securely.

  19. INSTALL FRONT SEAT HEADREST SUPPORT


    1. B005AMVC01
      *a Protrusion

      Align the protruding portion of the front seat headrest support with the installation groove of the front seatback spring assembly LH.

    2. Attach the 4 claws to install the 2 front seat headrest supports.

    3. B005A9B

      Close the 2 fasteners.

    4. B005892C01
      *1 Hog Ring Pliers

      Using hog ring pliers, install 5 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover LH or front seatback cover with pad.


      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover LH.

    5. Attach the 2 pieces of fastening tape and store the 2 fasteners.

  20. INSTALL SEAT COVER WIRE


    1. B005BHRN01

      Install the seat cover wire.

      Tech Tips


      • Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.


      • For wire 1000 mm (3.28 ft.) or less in length, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.


      • Make sure to read the precautions before preparing the wire.

        Click here

      Length
      A 440 mm (1.44 ft.)
      B 250 mm (9.84 in.)
      C 170 mm (6.70 in.)

      Tech Tips

      The dimensions shown in the illustration are the lengths.

      B0058PS

  21. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER LH

    Tech Tips


    • When installing the seat cover, refer to the precautions in order to prevent wrinkles from forming.

      Click here


    • Align the seam allowance in a single direction as shown in the illustration.

    B0057Q3N01

    1. B0058L0C01
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type front seat cushion cover LH to the separate type front seat cushion pad LH with 4 new hog rings in the order indicated in the illustration.

      Note


      • Be careful not to damage the separate type front seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

    2. B0058S4

      Return the seat cover wire to its original position.

      Tech Tips

      Use the same procedure for both seat cover wires.

    3. B0058LXC01
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type front seat cushion cover LH to the separate type front seat cushion pad LH with 14 new hog rings in the order indicated in the illustration.

      Note


      • Be careful not to damage the separate type front seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

    4. B00579MC01
      *1 Hog Ring Pliers

      Using hog ring pliers, install 2 new hog rings.

      Note


      • Be careful not to damage the separate type front seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

  22. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD LH


    1. Temporarily install the separate type front seat cushion cover with pad LH.

    2. for Front Passenger Side:

      Attach the claw to connect the occupant detection sensor connector.

    3. Attach the 9 hooks.

    4. Attach the 3 hooks.

    5. B0059MG

      w/ Seat Heater System:


      1. Attach the 3 clamps to connect the seat heater wire harness.

      2. Connect the connector.

      3. B00580X

        Attach the clamp to connect the seat heater wire harness.

      4. Connect the connector.

    6. B0059DEC01
      B008IZM Fastening Tape

      Attach the fastening tape to connect the front seat side airbag wire harness.

  23. INSTALL FRONT INNER SEAT CUSHION SHIELD LH


    1. B0059CT

      Attach the 3 guides and 2 claws to install the front inner seat cushion shield LH.

  24. INSTALL FRONT SEAT CUSHION SHIELD LH


    1. B0057WX

      Attach the 3 guides, 2 clips and claw to install the front seat cushion shield LH.

    2. Attach the 2 hooks to connect the 2 rubber bands.

  25. INSTALL FRONT SEAT CUSHION PROTECTOR


    1. Clean the vertical adjusting handle surface.

    2. B00587R

      Install a new front seat cushion protector as shown in the illustration.

  26. INSTALL VERTICAL ADJUSTING HANDLE LH


    1. Install the vertical adjusting handle LH with the screw.

  27. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    1. Attach the claw to install the reclining adjuster release handle LH.

  28. INSTALL SEAT ADJUSTER COVER CAP LH


    1. Install the 2 seat adjuster cover caps to the front seat adjuster assembly LH.

  29. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)

    Click here

  30. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)

    Click here