OCCUPANT DETECTION SENSOR REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during occupant detection sensor (separate type front seat cushion pad) removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Lane departure alert system (w/ Steering Control)

Click here

Pre-collision system
Memorize steering angle neutral point Parking assist monitor system

Click here

Panoramic view monitor system

Click here

CAUTION:


  • Wear protective gloves. Sharp areas on the parts may injure your hands.

  • B0084SX

    Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing.

    Click here

Tech Tips


  • Use the same procedure for the RHD side and LHD side.

  • The following procedure is for the LHD side.

PROCEDURE


  1. REMOVE FRONT SEAT ASSEMBLY (for Manual Seat)

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  2. REMOVE FRONT SEAT ASSEMBLY (for Power Seat)

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  3. REMOVE FRONT SEAT INNER BELT ASSEMBLY

    Click here

  4. DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER (for Manual Seat)

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  5. REMOVE VERTICAL ADJUSTING HANDLE (for Manual Seat)

    w/ Vertical Adjuster:

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  6. REMOVE RECLINING HINGE COVER (for Manual Seat)

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  7. REMOVE RECLINING ADJUSTER RELEASE HANDLE (for Manual Seat)

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  8. REMOVE SEAT ADJUSTER COVER CAP (for Manual Seat)

    w/ Vertical Adjuster:

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  9. REMOVE FRONT SEAT CUSHION SHIELD (for Manual Seat)

    w/o Vertical Adjuster:

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

    w/ Vertical Adjuster:

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  10. REMOVE FRONT SEAT INNER CUSHION SHIELD (for Manual Seat)

    w/o Vertical Adjuster:

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

    w/ Vertical Adjuster:

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  11. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY (for Manual Seat)

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  12. DISCONNECT SEPARATE TYPE FRONT SEATBACK COVER (for Power Seat)

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  13. REMOVE FRONT SEAT FRONT CUSHION SHIELD (for Power Seat)

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  14. REMOVE FRONT SEAT CUSHION SHIELD (for Power Seat)

    Click here

  15. REMOVE FRONT SEAT INNER CUSHION SHIELD (for Power Seat)

    Click here

  16. REMOVE SEPARATE TYPE FRONT SEATBACK ASSEMBLY (for Power Seat)

    w/o Front Seat Side Airbag:

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

    w/ Front Seat Side Airbag:

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  17. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

    for Manual Seat:

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

    for Power Seat:

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here

  18. REMOVE OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)


    1. Using a screwdriver, disengage the 14 claws and remove the occupant detection sensor (separate type front seat cushion pad) from the separate type front seat cushion cover as shown in the illustration.

      B0087WCC02
      *a Screwdriver - -

  19. REMOVE FRONT SEAT CUSHION HEATER ASSEMBLY (w/ Seat Heater System)

    Tech Tips

    Use the same procedure as for the driver seat.

    Click here