ROOF HEADLINING(w/ Rear No. 2 Seat) REASSEMBLY

PROCEDURE


  1. INSTALL NO. 1 ROOF WIRE


    1. When using a new roof headlining assembly:


      1. for LHD:


        1. Using a knife, cut the roof headlining assembly at the markings as shown in the illustration.

          B005N4LC01
          *A for Standard Roof *B for Sliding Roof
          *C w/ Rain Sensor *D w/ Pre-collision System with EC Mirror
          *E w/o Pre-collision System with EC Mirror *F w/ Pre-collision System
          *a Marking *b Cut

      2. for RHD:


        1. Using a knife, cut the roof headlining assembly at the markings as shown in the illustration.

          B005MW0C01
          *A for Standard Roof *B for Sliding Roof
          *C w/ Pre-collision System with EC Mirror *D w/o Pre-collision System with EC Mirror
          *E w/ Pre-collision System *F w/ Rain Sensor
          *a Marking *b Cut

    2. for LHD:


      1. Apply butyl tape as shown in the illustration.

        B005NSLC02
        *A for Standard Roof *B for Sliding Roof
        *a Marking - -
        B007ZL6 Butyl Tape - -

        Note

        Securely attach the butyl tape.

    3. for RHD:


      1. Apply butyl tape as shown in the illustration.

        B005LWHC02
        *A for Standard Roof *B for Sliding Roof
        *a Marking - -
        B007ZL6 Butyl Tape - -

        Note

        Securely attach the butyl tape.

    4. Turn the 2 visor connectors clockwise approximately 90° to install them to the roof headlining assembly.

      B005L9PC02
      *A for Standard Roof *B for Sliding Roof
      *a 90° - -
      B007Z37 Rotation Direction - -

    5. Engage each clamp.

    6. Align the marking tape (A) on the No. 1 roof wire with the vehicle front side tab of the roof headlining assembly.

      B005MFZC01
      *A for Standard Roof *B for Sliding Roof
      *a Marking Tape (A) *b Marking Tape (B)
      *c Vehicle Front Side Tab of the Roof Headlining Assembly *d Marking
      *e Adjustment Area - -

    7. Align the edge of the marking tape (B) on the No. 1 roof wire with the markings on the roof headlining assembly.

    8. Attach the No. 1 roof wire with the butyl tape.

      Note


      • Securely attach the No. 1 roof wire.

      • If any of the No. 1 roof wire is left loose, it will cause an abnormal noise.

      • Make sure to attach the No. 1 roof wire without leaving any of it loose.

      Tech Tips

      Secure the extra length of the No. 1 roof wire in the adjustment area.

    9. for LHD:


      1. Align the edge of the marking tape (C) on the No. 1 roof wire with the markings on the roof headlining assembly.

        B005NSXC02
        *A for Standard Roof *B for Sliding Roof
        *a Marking Tape (C) *b Marking
        B007ZL6 Adhesive Tape - -

    10. for RHD:


      1. Align the edge of the marking tape (C) on the No. 1 roof wire with the markings on the roof headlining assembly.

        B005MK6C02
        *A for Standard Roof *B for Sliding Roof
        *a Marking Tape (C) *b Marking
        B007ZL6 Adhesive Tape - -

    11. Install the No. 1 roof wire to the roof headlining assembly with adhesive tape.

      Note


      • Apply the tape securely in place.

      • Do not touch the adhesive surface when applying the tape to prevent adhesion failure.

  2. INSTALL TELEPHONE MICROPHONE ASSEMBLY

    Click here

  3. INSTALL VANITY LIGHT ASSEMBLY

    Click here

  4. INSTALL WASHER HOSE ASSEMBLY


    1. Apply butyl tape as shown in the illustration.

      B005LECC02
      *A for Standard Roof *B for Sliding Roof
      *a Marking - -
      B007ZL6 Butyl Tape - -

      Note

      Securely attach the butyl tape.

    2. Align the marking tape (A) on the washer hose assembly with the vehicle front side tab of the roof headlining assembly.

      B005LC7C02
      *A for Standard Roof *B for Sliding Roof
      *a Marking Tape (A) *b Marking Tape (B)
      *c Vehicle Front Side Tab of the Roof Headlining Assembly *d Marking
      *e Adjustment Area - -

    3. Align the edge of the marking tape (B) on the washer hose assembly with the marking on the roof headlining assembly.

    4. Attach the washer hose assembly with the butyl tape.

      Note


      • Securely attach the washer hose assembly.

      • If any of the washer hose assembly is left loose, it will cause an abnormal noise.

      • Make sure to attach the washer hose assembly without leaving any of it loose.

      Tech Tips

      Secure the extra length of the washer hose assembly in the adjustment area.

  5. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

    Click here