ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
*1 |
FRONT LOWER BUMPER ABSORBER |
*2 |
NO. 1 ENGINE UNDER COVER |
*3 |
NO. 2 ENGINE UNDER COVER |
*4 |
REAR ENGINE UNDER COVER LH |
*5 |
REAR ENGINE UNDER COVER RH |
- |
- |
ILLUSTRATION
*1 |
AIR CLEANER CAP SUB-ASSEMBLY |
*2 |
AIR CLEANER CASE SUB-ASSEMBLY |
*3 |
BATTERY |
*4 |
BATTERY CARRIER ASSEMBLY |
*5 |
NO. 2 CYLINDER HEAD COVER |
*6 |
BATTERY CLAMP SUB-ASSEMBLY |
*7 |
BATTERY TRAY |
*8 |
AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY |
*9 |
RADIATOR PIPE |
*10 |
BATTERY CLAMP BOLT |
 |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*1 |
FUEL TUBE SUB-ASSEMBLY |
*2 |
INLET HEATER WATER HOSE |
*3 |
NO. 1 FUEL VAPOR FEED HOSE |
*4 |
NO. 1 RADIATOR HOSE |
*5 |
NO. 2 RADIATOR HOSE |
*6 |
OUTLET HEATER WATER HOSE |
*7 |
UNION TO VACUUM TUBE HOSE |
*8 |
NO. 1 FUEL PIPE CLAMP |
*9 |
FUEL PIPE |
*10 |
BREATHER PLUG HOSE |
ILLUSTRATION
*1 |
COLUMN HOLE COVER SILENCER SHEET |
*2 |
GENERATOR ASSEMBLY |
*3 |
NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY |
*4 |
V-RIBBED BELT |
*5 |
ADJUSTING BAR |
*6 |
TERMINAL CAP |
*7 |
WIRE HARNESS CLAMP BRACKET |
*8 |
NO. 1 ENGINE ROOM RELAY BLOCK COVER |
*9 |
WIRE HARNESS |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*1 |
COMPRESSOR ASSEMBLY WITH PULLEY |
*2 |
DISCHARGE HOSE SUB-ASSEMBLY |
*3 |
SUCTION HOSE SUB-ASSEMBLY |
*4 |
O-RING |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
 |
for HFC-134a (R134a): Compressor oil ND-OIL 8 or equivalent for HFO-1234yf (R1234yf): Compressor oil ND-OIL 12 or equivalent |
- |
- |
ILLUSTRATION
*1 |
FRONT ENGINE MOUNTING INSULATOR |
*2 |
FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY |
*3 |
NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY |
*4 |
REAR ENGINE MOUNTING INSULATOR |
*5 |
TRANSMISSION CONTROL CABLE ASSEMBLY |
*6 |
FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT |
*7 |
FRONT SUSPENSION MEMBER REAR BRACE LH |
*8 |
FRONT SUSPENSION MEMBER REAR BRACE RH |
*9 |
FRONT SUSPENSION MEMBER REINFORCEMENT LH |
*10 |
FRONT SUSPENSION MEMBER REINFORCEMENT RH |
*11 |
FRONT CROSSMEMBER SUB-ASSEMBLY |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
 |
Do not apply lubricants |
ILLUSTRATION
*1 |
ENGINE MOUNTING INSULATOR LH |
*2 |
ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH |
*3 |
ENGINE WIRE |
*4 |
COOLER PIPE CLAMP BRACKET |
*5 |
RADIATOR RESERVOIR TANK |
*6 |
WIRE HARNESS CLAMP BRACKET |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
*1 |
CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY |
*2 |
DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
*3 |
DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT |
*4 |
FLYWHEEL HOUSING SIDE COVER |
*5 |
FLYWHEEL HOUSING UNDER COVER |
*6 |
STARTER ASSEMBLY |
*7 |
TRANSMISSION CONTROL CABLE ASSEMBLY |
*8 |
NO. 5 WATER BY-PASS HOSE |
*9 |
FRONT DRIVE PLATE SPACER |
*10 |
REAR DRIVE PLATE SPACER |
*11 |
GROUND WIRE |
- |
- |
*a |
BLACK: x 1 SILVER: x 5 |
- |
- |
|
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
★ |
Precoated part |
- |
- |