FUEL TANK INSTALLATION

PROCEDURE

  1. INSTALL FUEL EMISSION HOSE

    1. Install the fuel emission hose.

      Note:

      • Before connecting the fuel emission hose, check if there is any damage or foreign matter in the fuel emission hose or connector.

      • Check that the connector is connected by pulling on it.

      Tip:

      Firmly push the tube connector until a "click" sound is heard.

  2. INSTALL CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY

    1. Install the charcoal canister outlet tube sub-assembly to the fuel tank assembly and attach the 2 clamps.

  3. INSTALL FUEL TUBE GROMMET

    1. Install the 3 fuel tube grommets to the fuel tank assembly.

  4. INSTALL NO. 5 FUEL TUBE CLAMP

    1. Install the No. 5 fuel tube clamp to the fuel tank assembly.

  5. INSTALL NO. 3 FUEL TUBE CLAMP

    1. Install the No. 3 fuel tube clamp to the fuel tank assembly.

  6. INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

    1. Install the No. 1 fuel evaporation tube sub-assembly and attach the 5 clamps.

  7. INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

    1. Install the fuel tank main tube sub-assembly and attach the 5 clamps.

  8. INSTALL FUEL SENDER GAUGE ASSEMBLY

    Click here

  9. INSTALL FUEL SUCTION TUBE ASSEMBLY WITH PUMP

    Click here

  10. INSTALL FUEL TANK VENT TUBE SET PLATE

    Click here

  11. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

    Click here

  12. CONNECT FUEL EMISSION HOSE

    Click here

  13. INSTALL FUEL TANK ASSEMBLY

    1. Set the fuel tank assembly on an engine lifter with attachments.

    2. Lift up the engine lifter.

    3. Attach the wire harness to the 3 clamps.

    4. Connect the fuel pump connector and sender gauge connector.

      Note:

      Be careful not to cut the wiring.

    5. Install the No. 1 fuel tank band sub-assembly with the 2 bolts.

      45 N*m

      459 kgf*cm

      33 ft.*lbf

    6. Install the No. 1 fuel tank band sub-assembly LH with the 2 bolts.

      45 N*m

      459 kgf*cm

      33 ft.*lbf

    7. Install the No. 2 fuel tank band sub-assembly with the 2 bolts.

      45 N*m

      459 kgf*cm

      33 ft.*lbf

    8. Attach the 3 wire harness clamps.

  14. CONNECT NO. 3 FUEL TANK BREATHER TUBE SUB-ASSEMBLY

    1. Connect the No. 3 fuel tank breather tube sub-assembly to the fuel tank.

      Click here

  15. CONNECT CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY

    1. Connect the charcoal canister outlet tube sub-assembly to the fuel tank breather tube and slide the clamp to secure it.

    2. Attach the hose clamp.

  16. CONNECT FUEL TANK TO FILLER PIPE HOSE

    1. A300870C02

      *1

      Range

      *2

      Stopper

      *3

      Protrusion

      *a

      Top of Vehicle

      *b

      Bottom of Fuel Tank

      Connect the fuel tank to filler pipe hose to the fuel tank assembly and tighten the hose clamp.

      Tip:

      Make sure the hose clamp is oriented as shown in the illustration.

  17. INSTALL FUEL HOSE PROTECTOR

    1. Install the fuel hose protector to the fuel tank to filler pipe hose and attach the claw.

  18. CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

    1. Connect the No. 1 fuel evaporation tube sub-assembly and slide the clamp to secure it.

  19. CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

    1. Connect the fuel tank main tube sub-assembly.

      Click here

  20. INSTALL NO. 1 FLOOR UNDER COVER

    1. Attach the 2 clips and install the No. 1 floor under cover with the 2 nuts.

  21. INSTALL NO. 1 FUEL TANK PROTECTOR

    1. Attach the 3 clips and install the No. 1 fuel tank protector with the nut.

      20 N*m

      204 kgf*cm

      15 ft.*lbf

  22. INSTALL FRONT FLOOR COVER

    1. Install the front floor cover and attach the 5 clips.

    2. Install the bolt and nut.

      for bolt

      12 N*m

      122 kgf*cm

      9 ft.*lbf

      for nut

      6.0 N*m

      61 kgf*cm

      53 in.*lbf

  23. CONNECT PARKING BRAKE CABLE

    1. Connect the parking brake cable with the 2 bolts.

      6.0 N*m

      61 kgf*cm

      53 in.*lbf

  24. ADD FUEL

  25. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click hereClick hereClick hereClick here

  26. INSPECT FOR FUEL LEAK

    Click here