AUTOMATIC HEADLIGHT BEAM LEVEL CONTROL SYSTEM(for Sedan) Headlight Beam Level Control Actuator Circuit
| DTC Code | DTC Name |
|---|---|
| Headlight Beam Level Control Actuator Circuit |
DESCRIPTION
The headlight leveling ECU assembly actuates the headlight leveling motors according to the vehicle conditions.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
Make sure to perform vehicle information synchronization and initialization after replacing the headlight leveling ECU assembly.
PROCEDURE
PERFORM ACTIVE TEST USING GTS
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / HL AutoLeveling / Active Test.
Perform the Active Test according to the display on the GTS.
Body Electrical > HL AutoLeveling > Active Test
Tester Display
Measurement Item
Control Range
Diagnostic Note
Drive The Leveling Motor
Headlight leveling motor upward or downward operation
Up/Down/Stop
Perform the Active Test with the engine started and vehicle stopped
Body Electrical > HL AutoLeveling > Active Test
Tester Display
Drive The Leveling Motor
OK
Headlight leveling motors operate normally.
Result
Proceed to
OK
NG
CHECK HARNESS AND CONNECTOR (HEADLIGHT UNIT (HEADLIGHT LEVELING MOTOR) - HEADLIGHT LEVELING ECU ASSEMBLY)
Disconnect the A182 headlight leveling ECU assembly connector.
Disconnect the A178 or A180 headlight unit (headlight leveling motor) connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance
Table 1. LH Side Tester Connection
Condition
Specified Condition
A182-18 (LHT) - A178-2 (LH T)
Always
Below 1 Ω
A182-11 (LH+) - A178-3 (LHIG)
Always
Below 1 Ω
A182-24 (LH-) - A178-1 (LH E)
Always
Below 1 Ω
A182-18 (LHT) or A178-2 (LH T) - Body ground
Always
10 kΩ or higher
A182-11 (LH+) or A178-3 (LHIG) - Body ground
Always
10 kΩ or higher
A182-24 (LH-) or A178-1 (LH E) - Body ground
Always
10 kΩ or higher
Table 2. RH Side Tester Connection
Condition
Specified Condition
A182-17 (RHT) - A180-2 (RH T)
Always
Below 1 Ω
A182-10 (RH+) - A180-3 (RHIG)
Always
Below 1 Ω
A182-23 (RH-) - A180-1 (RH E)
Always
Below 1 Ω
A182-17 (RHT) or A180-2 (RH T) - Body ground
Always
10 kΩ or higher
A182-10 (RH+) or A180-3 (RHIG) - Body ground
Always
10 kΩ or higher
A182-23 (RH-) or A180-1 (RH E) - Body ground
Always
10 kΩ or higher
Result
Proceed to
OK
NG
NG REPAIR OR REPLACE HARNESS OR CONNECTOR
REPLACE HEADLIGHT UNIT (HEADLIGHT LEVELING MOTOR)
Replace the headlight unit (headlight leveling motor) with a new or known good one.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / HL AutoLeveling / Active Test.
Perform the Active Test according to the display on the GTS.
Body Electrical > HL AutoLeveling > Active Test
Tester Display
Measurement Item
Control Range
Diagnostic Note
Drive The Leveling Motor
Headlight leveling motor upward or downward operation
Up/Down/Stop
Perform the Active Test with the engine started and vehicle stopped
Body Electrical > HL AutoLeveling > Active Test
Tester Display
Drive The Leveling Motor
OK
Headlight leveling motors operate normally.
Result
Proceed to
OK
NG
OK END (HEADLIGHT UNIT (HEADLIGHT LEVELING MOTOR) WAS DEFECTIVE)