LIGHTING SYSTEM ACC Signal Circuit

DTC Code DTC Name
ACC Signal Circuit

DESCRIPTION

This circuit detects the ignition switch ACC or off condition, and sends it to the main body ECU (multiplex network body ECU).

WIRING DIAGRAM

E227110E04

CAUTION / NOTICE / HINT

Note:

Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

  1. READ VALUE USING GTS

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Body Electrical / Main Body / Data List.

    5. Read the Data List according to the display on the GTS.

      Body Electrical > Main Body > Data List

      Tester Display

      Measurement Item

      Range

      Normal Condition

      Diagnostic Note

      ACC SW

      Ignition switch ACC signal

      ON or OFF

      ON: Ignition switch ACC

      OFF: Ignition switch off

      -

      Body Electrical > Main Body > Data List

      Tester Display

      ACC SW

      OK

      Normal conditions listed above are displayed.

    Result

    Proceed to

    OK

    NG
    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

    Click hereClick here

    NG

  2. CHECK HARNESS AND CONNECTOR (ACC RELAY POWER SOURCE)

    1. E258613C06

      *a

      Component with harness connected

      (Instrument Panel Junction Block Assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      3D-25 - Body ground

      Ignition switch ACC

      11 to 14 V

    Result

    Result

    Proceed to

    OK

    A

    NG (w/ Entry and Start System)

    B

    NG (w/o Entry and Start System)

    C
    B

    GO TO ENTRY AND START SYSTEM (for Start Function)

    Click here

    C

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    A

  3. CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BATTERY AND BODY GROUND)

    1. Disconnect the 3B and 3C instrument panel junction block assembly connectors.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection

      Condition

      Specified Condition

      3B-1 - Body ground

      Always

      11 to 14 V

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      3C-9 - Body ground

      Always

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY (ACC RELAY)

    1. Remove the instrument panel junction block assembly.

    2. Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      E258619C02

      *a

      Component without harness connected

      (Instrument Panel Junction Block Assembly)

      -

      -

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      3B-1 - MB-29 (ACC)

      Battery not connected to 3D-25 and 3C-9

      10 kΩ or higher

      3B-1 - MB-29 (ACC)

      Battery positive (+) → 3D-25

      Battery negative (-) → 3C-9

      Below 1 Ω

    Result

    Proceed to

    OK

    NG
    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

    NG

    REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY