REAR SEAT ASSEMBLY(for Hatchback) REASSEMBLY

PROCEDURE

  1. INSTALL BENCH TYPE REAR SEAT CUSHION COVER

    1. Temporarily install the bench type rear seat cushion cover to the bench type rear seat cushion pad.

    2. Using hog ring pliers, install 14 new hog rings.

      B327167
      Note:

      • Be careful not to damage the bench type rear seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the bench type rear seat cushion cover.

    3. Using hog ring pliers, install 26 new hog rings.

      B333493
      Note:

      • Be careful not to damage the bench type rear seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the bench type rear seat cushion cover.

  2. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH (for RH Side)

    1. B327119

      Engage the 2 guides.

    2. Install the rear seat lock control lever sub-assembly RH with the screw.

      2.0 N*m

      20 kgf*cm

      18 in.*lbf

  3. INSTALL REAR SEATBACK LOCK ASSEMBLY RH (for RH Side)

    1. B330169

      Engage the lock clip as shown in the illustration.

    2. Install the rear seatback lock sub-assembly RH with the 2 bolts.

      24 N*m

      245 kgf*cm

      18 ft.*lbf

  4. INSTALL REAR CENTER SEAT OUTER BELT ASSEMBLY (for RH Side)

  5. INSTALL SEPARATE TYPE REAR SEATBACK COVER RH (for RH Side)

    1. Temporarily install the separate type rear seatback cover RH to the separate type rear seatback pad RH.

    2. B336640

      w/o Center Armrest:

      1. Using hog ring pliers, install the separate type rear seatback cover RH to the separate type rear seatback pad RH with 7 new hog rings.

        Note:

        • Be careful not to damage the separate type rear seatback cover RH.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover RH.

    3. B339778

      w/ Center Armrest:

      1. Using hog ring pliers, install the separate type rear seatback cover RH to the separate type rear seatback pad RH with 7 new hog rings.

        Note:

        • Be careful not to damage the separate type rear seatback cover RH.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover RH.

  6. INSTALL SEATBACK COVER WITH PAD (for RH Side)

    1. B327115

      Pass the rear center seat outer belt assembly through the seatback cover with pad as shown in the illustration.

    2. B333495

      Engage the 2 guides and 2 claws to install the rear seat shoulder belt cover.

    3. B327112

      Engage the 4 claws to install the 2 rear seat headrest supports.

    4. B327113

      w/ Center Headrest:

      1. Engage the 4 claws to install the 2 rear seat headrest supports.

    5. B336636

      Engage the 2 hooks.

    6. B339775

      Engage the 3 hooks.

    7. B339769

      Close the fastener as shown in the illustration.

    8. B336634

      Engage the 2 clips.

    9. B339772C01

      *a

      Fastener

      Engage the 2 fasteners as shown in the illustration.

    10. B336633

      Install the 3 clips.

  7. INSTALL REAR SEATBACK LOCK BEZEL (for RH Side)

    1. B333477

      Engage the 5 claws to install a new rear seatback lock control bezel RH.

  8. INSTALL SEAT BELT ANCHOR COVER CAP (for RH Side)

    1. B327101

      Engage the 2 claws to install the seat belt anchor cover cap.

  9. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY (w/ Center Armrest)

    1. B327098

      Install the bush as shown in the illustration.

    2. B333501E01

      Engage the pin as indicated by the arrows, in the order shown in the illustration.

    3. B327094

      Install the rear seat center armrest assembly with the bolt and bush.

      6.0 N*m

      61 kgf*cm

      53 in.*lbf

  10. INSTALL CENTER ARMREST HINGE COVER (w/ Center Armrest)

    1. B333496

      Engage the claw to install the center armrest hinge cover as shown in the illustration.

  11. INSTALL REAR SEATBACK COVER (for RH Side)

    1. B327099

      Engage the 4 claws to install the rear seatback cover.

  12. INSTALL REAR SEAT INNER WITH CENTER BELT ASSEMBLY RH (for RH Side)

    1. B333476

      Install the washer to connect the rear seat inner with center belt assembly RH to the rear center seat outer belt assembly.

  13. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY LH (for LH Side)

    Tip:

    Use the same procedure as for the RH side.

  14. INSTALL REAR SEATBACK LOCK ASSEMBLY LH (for LH Side)

    Tip:

    Use the same procedure as for the RH side.

  15. INSTALL SEPARATE TYPE REAR SEATBACK COVER LH (for LH Side)

    1. Temporarily install the separate type rear seatback cover LH to the separate type rear seatback pad LH.

    2. B336641

      Using hog ring pliers, install the separate type rear seatback cover LH to the separate type rear seatback pad LH with 7 new hog rings.

      Note:

      • Be careful not to damage the separate type rear seatback cover LH.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover LH.

  16. INSTALL SEATBACK COVER WITH PAD (for LH Side)

    1. B327161

      Temporarily install the seatback cover with pad to the rear seatback frame sub-assembly as shown in the illustration.

    2. B330065

      Engage the 4 claws to install the 2 rear seat headrest supports.

    3. B336628

      Engage the 4 hooks.

    4. B336647

      Close the fastener as shown in the illustration.

    5. B333487

      Engage the 2 clips.

    6. B333498C01

      *a

      Fastener

      Engage the 2 fasteners as shown in the illustration.

    7. B327120

      Install the 2 clips.

  17. INSTALL REAR SEATBACK LOCK BEZEL LH (for LH Side)

    Tip:

    Use the same procedure as for the RH side.

  18. INSTALL REAR SEATBACK COVER (for LH Side)

    Tip:

    Use the same procedure as for the RH side.