STOP AND START SYSTEM, Diagnostic DTC:P060B

DTC Code DTC Name
P060B Analog to Digital Converter Malfunction

DESCRIPTION

If an internal malfunction occurs in the engine stop and start ECU, it stores P060B and blinks the stop and start cancel indicator light.

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

Warning Indicate

Memory

P060B

Analog to Digital Converter Malfunction

Both of the following conditions are met for 0.7 seconds or more (1 trip detection logic):

  • Ignition switch is turned to ON

  • Engine stop and start ECU has an internal malfunction

Engine stop and start ECU

Blinks

DTC stored

CONFIRMATION DRIVING PATTERN

Tip:

  • DTCs for the stop and start system are not cleared automatically, even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs

    Click here

  • Check the number of starter operations.

    Click hereClick here

  1. STOP AND START SYSTEM OPERATION CHECK

    Tip:

    • When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited until refresh charge is completed. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).

    • Allow the engine to idle for 3 minutes after it is warmed up and check that the engine idle speed is within 50 rpm of the target idle speed.

    1. Start the engine and warm it up.

    2. Turn the air conditioning system off.

    3. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing Confirmation Driving Pattern, obey all speed limits and traffic laws.

    4. Stop the vehicle, move the shift lever to neutral and release the clutch pedal.

    5. Allow the engine to be stopped by stop and start control.

    6. Depress the clutch pedal to start the engine.

CAUTION / NOTICE / HINT

Note:

  • Before replacing the engine stop and start ECU, download the current status (number of starter operations) and upload it into a new engine stop and start ECU.

    Click here

  • After replacing the engine stop and start ECU or air conditioning control assembly, initialize and perform learning of the air conditioning information in the engine stop and start ECU.

    Click here

  • After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

    Click here

Tip:

  • DTCs for the stop and start system are not cleared automatically, even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

    Click here

  • Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

    Click hereClick here

PROCEDURE

  1. CLEAR DTC

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Stop and Start / Trouble Codes.

    5. Clear the DTC.

      Powertrain > Stop and Start > Clear DTCs

    Result

    Proceed to

    NEXT
    NEXT

  2. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P060B)

    1. Turn the ignition switch to off and wait for 30 seconds or more.

    2. Turn the ignition switch to ON.

    3. Start the engine.

    4. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    5. Enter the following menus: Powertrain / Stop and Start / Trouble Codes.

    6. Read the DTCs.

      Powertrain > Stop and Start > Trouble Codes

      Result

      Result

      Proceed to

      DTC P060B is output

      A

      DTC P060B and other DTCs are output

      B

      DTCs are not output

      C
    A

    REPLACE ENGINE STOP AND START ECU

    Click here

    B

    GO TO DTC CHART

    Click hereClick hereClick here

    C

    USE SIMULATION METHOD TO CHECK

    Click hereClick hereClick here