ENTRY AND START SYSTEM


  1. FUNCTION OF MAIN COMPONENTS


    1. The main components for the start function have the following functions:

      Component Function
      Engine Switch (Push Start Switch)

      • Transmits the engine switch signal to the certification ECU (smart key ECU assembly).

      • Receives the ID code and transmits it to the certification ECU (smart key ECU assembly) when the key battery is too weak to respond to the tuner based on the signals from the room antennas.
      Electrical Key Transmitter Sub-assembly Receives the signals from the antennas and returns the ID code to the smart door control receiver assembly.
      Electrical Key (Card Key) Transmitter Sub-assembly*
      No. 1 Indoor Electrical Key Antenna Assembly (Front), No. 2 Indoor Electrical Key Antenna Assembly (Center), No. 3 Indoor Electrical Key Antenna Assembly (Rear) Receives a request signal from the certification ECU (smart key ECU assembly) and forms the actuation area in the vehicle.
      Smart Door Control Receiver Assembly Receives the ID code from the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* and transmits it to the certification ECU (smart key ECU assembly).
      Certification ECU (Smart Key ECU Assembly)

      • Certifies the ID code received from the smart door control receiver assembly and transmits the certification results to the steering lock ECU (steering lock actuator assembly).

      • Transmits the steering wheel lock/unlock signals.

      • Transmits the immobiliser set/unset request signals.

      • Switches the power source ("engine switch") among 4 modes (off, on (ACC), on (IG), start) in accordance with the shift position and the brake pedal signal.

      • Controls the entry and start system in accordance with the signals received from the switches and each ECU.
      Stop Light Switch Assembly Outputs the state of the brake pedal to the certification ECU (smart key ECU assembly).
      Steering Lock ECU (Steering Lock Actuator Assembly) Receives the steering wheel unlock/lock request signal from the certification ECU (smart key ECU assembly), and activates the steering lock motor.
      Combination Meter Assembly Multi Buzzer Sounds to inform the driver of malfunctions in the entry and start system.
      Multi-information Display Informs the driver of power source or system abnormalities by displaying a warning message.

      *: Models with card key

    2. The main components for the entry function* have the following functions:


      • *: Models with entry function

      Component Function
      Electrical Key Transmitter Sub-assembly

      • Outputs information such as the key ID and vehicle ID when request signals that are output by the room and door antennas are received.

      • Outputs a request signal when the lock, unlock, panic*1, or power back door button*2 on the electrical key transmitter sub-assembly is pushed.

      • Outputs information such as the key ID and vehicle ID when the radio wave signal that is output by the transponder key amplifier in the engine switch is received.

      • Has an integrated mechanical key that can be used to unlock the doors when the key battery is weak.
      Electrical Key (Card Key) Transmitter Sub-assembly*3

      • Outputs information such as the key ID and vehicle ID when request signals that are output by the room and door antennas are received.

      • Outputs information such as the key ID and vehicle ID when the radio wave signal that is output by the transponder key amplifier in the engine switch is received.

      • Has an integrated mechanical key that can be used to unlock the doors when the key battery is weak.
      Main Body ECU (Multiplex Network Body ECU)

      • Receives the request signal from the certification ECU (smart key ECU assembly), and actuates the door lock motors to unlock or lock all the doors.

      • Transmits the condition of each door to the certification ECU (smart key ECU assembly).
      Certification ECU (Smart Key ECU Assembly)

      • Certifies the ID code received from the smart door control receiver assembly and transmits the certification results to the steering lock ECU (steering lock actuator assembly).

      • Controls the antennas and touch sensors.

      • Transmits the door lock/unlock request signals during the entry function.
      Front and Rear Outside Door Handle Assembly Door Electrical Key Antenna Receives a request signal from the certification ECU (smart key ECU assembly) and creates an actuation area around the front and rear doors.
      Lock Sensor Transmits door lock request signals to the certification ECU (smart key ECU assembly).
      Unlock Sensor Detects when a person touches the inside of an outside door handle.
      Electrical Key Antenna Receives a request signal from the certification ECU (smart key ECU assembly) and forms an actuation area around the back door.
      No. 1 Indoor Electrical Key Antenna Assembly (Front), No. 2 Indoor Electrical Key Antenna Assembly (Center), No. 3 Indoor Electrical Key Antenna Assembly (Rear) Receives a request signal from the certification ECU (smart key ECU assembly) and forms an actuation area in the vehicle.
      Power Back Door Close and Lock Switch (Door Control Switch)*2 The power back door closes and locks when the power back door close and lock switch on the back door jamb is turned on.
      Kick Door Control Sensor*4 The back door opens and closes when the touchless kick actuation operation is detected.
      Smart Door Control Receiver Assembly Receives the ID code from the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*3 and transmits it to the certification ECU (smart key ECU assembly).
      Combination Meter Assembly Multi Buzzer Sounds to inform the driver of malfunctions in the entry and start system.
      Multi-information Display Informs the driver of power source or system abnormalities by displaying a warning message.
      Wireless Door Lock Buzzer*5

      • Sounds as an answer back for entry lock/unlock and wireless lock/unlock to inform the driver.*6

      • Sounds to inform the driver of malfunctions in the entry and start system.

      *1: Models with panic alarm function

      *2: Models with power back door system

      *3: Models with card key

      *4: Models with hands free power back door

      *5: Except models for China

      *6: Models with wireless door lock buzzer answer back function

  2. OPERATION


    1. The special functions of the entry and start system only work when the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* is in the actuation area formed by the antennas.


      • *: Models with card key

    2. The No. 1, No. 2 and No. 3 indoor electrical key antenna assemblies form the actuation area of the start function.

    3. The door electrical key antennas and the electrical key antenna form the actuation area of the entry function.

      B002FQTC01
      *1 No. 1 Indoor Electrical Key Antenna Assembly (Front) *2

      Front Outside Door Handle Assembly LH


      • Door Electrical Key Antenna
      *3

      Rear Outside Door Handle Assembly LH


      • Door Electrical Key Antenna

      		 *4 No. 3 Indoor Electrical Key Antenna Assembly (Rear)
      *5 Electrical Key Antenna *6

      Rear Outside Door Handle Assembly RH


      • Door Electrical Key Antenna
      *7 No. 2 Indoor Electrical Key Antenna Assembly (Center) *8

      Front Outside Door Handle Assembly RH


      • Door Electrical Key Antenna
      *a Approx. 0.7 m to 1.0 m (2.3 ft. to 3.3 ft.) *b Exterior Actuation Area
      *c Interior Actuation Area - -
      Actuation Area Detail
      Interior The interior actuation area of the indoor electrical key antennas (front, center, rear) is formed when the driver door is opened or closed, when the engine switch is pushed, when a warning is activated, or when a lock sensor is on.
      Exterior The exterior actuation area formed by the front and rear door electrical key antennas (LH, RH) and electrical key antenna is approximately 0.7 to 1.0 m (2.3 to 3.3 ft.) from the outside door handle or the center of the rear bumper.
      Around Front Doors and Rear Doors The exterior actuation area of the door electrical key antennas is formed by transmitting a request signal every 0.25 seconds while the engine switch is off and each door is locked. In this way, the presence of an electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is detected. When locking the door using the lock sensor on the outside door handle, the actuation area is formed when the lock sensor is touched.
      Around Back Door The exterior actuation area of the electrical key antenna is formed when the back door lock switch, back door unlock switch or power back door close and lock switch*2 is on or performing the touchless kick actuation operation*3.

      *1: Models with card key

      *2: Models with power back door system

      *3: Models with hands free power back door

  3. FUNCTION


    1. Start Function


      1. The start function has different power source change patterns to suit the brake pedal state and shift lever position.

        Pattern Brake Pedal Shift Lever Position Power Source Change Pattern
        A Depressed P or N

        When the engine switch is pushed once.


        • Off → on (IG) (after the engine is started)
        B Not Depressed P

        Each time the engine switch is pushed.


        • Off → on (ACC) → on (IG) → off
        C Except P

        Each time the engine switch is pushed.


        • Off → on (ACC) → on (IG) → on (ACC)
        D - P

        When the engine switch is pushed in the on (IG) condition.


        • On (IG) (engine is started or not started) → off
        E - Except P

        When the engine switch is pushed in the on (IG) condition.


        • On (IG) (engine is started or not started) → on (ACC)
        B002FD1E06

        Note


        • Normally, the operation of the engine switch is disabled while the vehicle is being driven. However, in an emergency, by pushing the engine switch for approximately 2 seconds or more or pushing the engine switch 3 times or more in a row, the driver can stop the engine while the vehicle is in motion.

        • If no signals are transmitted to the certification ECU (smart key ECU assembly) due to malfunctions in the stop light switch assembly, the engine may not start when the engine switch is pushed with the brake pedal depressed. In such cases, performing the following procedure may enable the engine to start: 1) push the engine switch to turn the power source from off to on (ACC), and 2) push the engine switch again and hold it for 15 seconds or more.

        • The above 2 operations must be applied only in emergency situations. Under normal conditions, the engine must not be stopped by pushing the engine switch while driving. Also, it should not be started without depressing the brake pedal or when the shift lever is in any position other than P or N.

    2. Entry Unlock (Models with Entry Function)


      1. When the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is in the actuation area formed by the door electrical key antenna, holding the outside door handle assembly of the driver seat and touching the built-in touch sensor unlocks the driver door only, and holding any of the passenger side or rear outside handle assemblies and touching the built-in touch sensor unlocks all the doors. (Driver door mode)

      2. When the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is in the actuation area formed by the door electrical key antenna, holding any of the outside door handle assemblies and touching the built-in touch sensor unlocks all the doors. (All door mode)

      3. When the doors are unlocked, the hazard warning lights flash twice and the buzzer sounds twice*2 as an answer back.

        Tech Tips

        If the doors are locked by wireless operation, the entry and start system or key linked power door lock operation, it may not be possible to unlock the doors using the entry and start system. In this situation, use the wireless function of the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 to unlock the doors.


        • *1: Models with card key

        • *2: Models with wireless door lock buzzer answer back function

        B002FDX

    3. Entry Lock (Models with Entry Function)


      1. When the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is in any of the exterior actuation areas, all doors are locked by touching the lock sensor of the front or rear outside door handle assembly or by pressing the back door lock switch of the back door.

      2. After all doors have been locked, the wireless door lock buzzer sounds once*2 as an answer back and the hazard lights flash once at the same time.

      3. If the doors do not lock when the lock sensor on the topside of an outside door handle assembly is touched, touch the lock sensors on the top and bottom sides simultaneously by pinching the handle.


        • *1: Models with card key

        • *2: Models with wireless door lock buzzer answer back function

        B002FLD

      4. When the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* is in the back door exterior actuation area with all the doors closed, all doors are locked by pressing the back door lock switch.


        • *: Models with card key

        B002FKIC01
        *1 Back Door Opener Switch (Back Door Lock Switch) - -

    4. Entry Back Door Unlock Function (Models with Entry Function)


      1. When the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* is in the actuation area surrounding the back door, pressing the back door unlock switch will unlock the back door.


        • *: Models with card key

        B002FJXC01
        *1 Back Door Opener Switch (Back Door Unlock Switch) - -

      2. When the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is in the actuation area surrounding the back door, performing a touchless kick actuation operation towards the center of the rear bumper will unlock all the doors.*2


        • *1: Models with card key

        • *2: Models with hands free power back door

        B002FMLC01
        *1 Kick Door Control Sensor *2 Electrical Key Transmitter Sub-assembly or Electrical Key (Card Key) Transmitter Sub-assembly
        *a The user carrying an electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly stands around the center of the rear bumper while maintaining a certain distance (approximately equal to the length of the arm) from the rear bumper. *b The user waves a foot within approximately 100 mm (3.94 in.) from the surface of the rear bumper.
        *c The user moves the foot away from the surface of the rear bumper. - -

    5. Power Back Door Close and Lock Function (Models with Power Back Door System)


      1. While the back door is open, when the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* is in the actuation area surrounding the back door, pressing the power back door close and lock switch will close and then lock all doors.

        Note


        • When the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* is too close to the actuation area, such as when the driver approaches the vehicle with the electrical key in their shirt pocket, the system may determine that the key is within the cabin and the key lock-in prevention function will prevent the back door from closing when the power power back door close and lock switch is pressed.

        • When the power back door close and lock switch is pressed by a hand carrying an electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*, the system may determine that the key is outside the actuation area and the back door may not close. Also, when the power power back door close and lock switch is pressed while an electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* is in a bag on the ground, the system may determine that the key is outside the actuation area and the back door may not close.


        • *: Models with card key

        B002FH0C01
        *1 Power Back Door Close and Lock Switch (Door Control Switch) - -

    6. Warning


      1. When any of the situations below occur, the entry and start system sounds the wireless door lock buzzer* and a buzzer in the combination meter assembly and displays a message on the multi-information display in order to alert the driver.


        • *: Except models for China

        Situation Condition
        A The engine is left running and the shift lever is in a position other than P when the driver gets out of the vehicle.
        B The engine is left running and the shift lever is in P when the driver gets out of the vehicle.
        C The engine is left running when a passenger gets out of the vehicle while holding the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1.
        D The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is not within the actuation areas.
        E The vehicle is driven without an electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1.
        F The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is left in the vehicle.
        G*2 A door is ajar.
        H The key reminder sounds.
        I The key battery is weak.
        J Steering lock does not release.
        K A malfunction has been detected in a vehicle speed signal, etc.
        L The engine cannot be started (system/driver error).
        M Immobiliser system certification confirmation occurs.
        N Engine start operation guide (ACC ON)
        O Engine start operation guide (IG ON)
        P The engine switch cannot be turned off (shift lever in any position except P).
        Q The engine switch cannot be turned off (shift lever in P).
        R Auto power off operation occurs.
        S Engine emergency stop operation is performed.
        T Engine switch is operated while driving.
        U Engine switch is operated while driving.
        V Accessory state
        W Ignition on state

        *1: Models with card key

        *2: Except models for China

      2. Situation A


        • There are 2 patterns for situation A.

        • Pattern 1:

        • When the shift lever is in a position other than P, the driver opens the door and attempts to get out of the vehicle. In this situation, the following control is performed:

          Possible Effects without Warning Sudden vehicle movement, Vehicle theft, Vehicle roll-away (Vehicle creep, such as when N is selected)
          Warning Active Condition

          The warning is activated when all of the following conditions are met:


          • The engine switch is on (ACC) or on (IG).

          • The shift lever is in any position except P.

          • The driver door is opened.

          • The vehicle speed is not detected.
          Warning Method Combination Meter Assembly Multi Buzzer Sounds continuously
          Multi-information Display

          The following warning message is displayed:


          • Shift to P Before Exiting Vehicle
          Advisory Display -
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The warning is stopped when one of the following conditions is met:


          • The engine switch is turned off.

          • The shift lever is moved to P.

          • The driver door is closed.

          • The vehicle speed is above 5 km/h (3 mph).

        • Pattern 2:

        • Under the situation of pattern 1, the driver closes the door and attempts to leave the vehicle while holding the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1. In this situation, the following control is performed:

          Possible Effects without Warning Sudden vehicle movement, Vehicle theft, Vehicle roll-away (Vehicle creep, such as when N is selected)
          Warning Active Condition

          The warning is activated when all of the following conditions are met:


          • The engine switch is on (ACC) or on (IG).

          • The shift lever is in any position except P.

          • The driver door is opened → closed.

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is not detected in the vehicle (interior key certification fails).

          • The vehicle speed is not detected.
          Warning Method Combination Meter Assembly Multi Buzzer Sounds continuously
          Multi-information Display

          The following warning messages are alternately displayed:


          • Shift to P Before Exiting Vehicle

          • Key Not Detected Check Key Location
          Advisory Display -
          Wireless Door Lock Buzzer Sounds continuously*2
          Buzzer and Wireless Door Lock Buzzer Warning Stop Condition

          The warning is stopped when one of the following conditions is met:


          • The engine switch is turned off.

          • The shift lever is moved to P.

          • The vehicle speed is above 5 km/h (3 mph).

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is detected in the vehicle (interior key certification result is OK).
          "Shift to P Before Exiting Vehicle" Message Warning Stop Condition

          The warning is stopped when either of the following conditions is met:


          • The shift lever is moved to P.

          • The vehicle speed is above 5 km/h (3 mph).
          "Key Not Detected Check Key Location" Message Warning Stop Condition

          The warning is stopped when either of the following conditions is met:


          • The engine switch is turned off.

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is detected in the vehicle (interior key certification result is OK).

          • *1: Models with card key

          • *2: Except models for China

      3. Situation B


        • There are 3 patterns for situation B.

        • Pattern 1:

        • When the shift lever is in P and the engine switch is in a mode other than off (the steering remains unlocked), the driver door is opened and the driver attempts to leave the vehicle. In this situation, the following control is performed:

          Possible Effects without Warning Vehicle theft
          Warning Active Condition

          Condition 1

          The warning is activated when both of the following conditions are met:


          • The engine switch is on (ACC).

          • The driver door is open.

          Condition 2

          The warning is activated when all of the following conditions are met for 1 second:


          • The engine switch is turned off.

          • The steering lock remains unlocked.

          • The driver door is open.
          Warning Method Combination Meter Assembly Multi Buzzer Sounds continuously at short and even intervals
          Multi-information Display -
          Advisory Display -
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The warning is stopped when one of the following conditions is met:


          • The engine switch is turned on (IG).

          • The driver door is closed.

          • The engine switch is turned off and the steering wheel lock control is performed.

        • Pattern 2:

        • Under the situation of pattern 1, the driver opens and closes the driver door and attempts to leave the vehicle while holding the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1. In this situation, the following control is performed:

          Possible Effects without Warning Vehicle theft
          Warning Active Condition

          The warning is activated when all of the following conditions are met:


          • The engine switch is on (ACC) or on (IG).

          • The shift lever is in P.

          • The driver door is opened → closed.

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is not detected in the vehicle (interior key certification fails).

          • The vehicle speed is not detected.
          Warning Method Combination Meter Assembly Multi Buzzer Sounds once
          Multi-information Display

          The following warning message is displayed:


          • Key Not Detected Check Key Location
          Advisory Display -
          Wireless Door Lock Buzzer Sounds 3 times*2
          Warning Stop Condition

          The warning is stopped when either of the following conditions is met:


          • The engine switch is turned off.

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is detected in the vehicle (interior key certification result is OK).

          • *1: Models with card key

          • *2: Except models for China

        • Pattern 3:

        • Under the situation of pattern 2, the driver touches the lock sensor on the outside door handle. In this situation, the following control is performed:

          Possible Effects without Warning Vehicle theft
          Warning Active Condition

          The warning is activated when all of the following conditions are met:


          • The engine switch is on (ACC) or on (IG).

          • The shift lever is in P.

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is not detected in the vehicle (interior key certification fails), but detected in an outside detection area (exterior key certification result is OK).

          • The lock sensor on the outer door handle is on (touched).

          • The vehicle speed is not detected.
          Warning Method Combination Meter Assembly Multi Buzzer Sounds once
          Multi-information Display

          The following warning messages are alternately displayed:


          • Turn Off Vehicle

          • Key Not Detected Check Key Location
          Advisory Display -
          Wireless Door Lock Buzzer Sounds continuously*2
          Wireless Door Lock Buzzer Warning Stop Condition

          The warning is stopped when one of the following conditions is met:


          • 5 seconds elapse.

          • The engine switch is turned off.

          • The shift lever is moved to any position except P.

          • The vehicle speed is above 5 km/h (3 mph).

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is detected in the vehicle (interior key certification result is OK).

          • Any door is opened or closed.
          "Turn Off Vehicle" Message Warning Stop Condition

          The warning is stopped when one of the following conditions is met:


          • 60 seconds elapse.

          • The engine switch is turned off.

          • The shift lever is moved to any position except P.

          • The vehicle speed is above 5 km/h (3 mph).
          "Key Not Detected Check Key Location" Message Warning Stop Condition

          The warning is stopped when either of the following conditions is met:


          • The engine switch is turned off.

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is detected in the vehicle (interior key certification result is OK).

          • *1: Models with card key

          • *2: Except models for China

      4. Situation C


        • When the engine is left running, a passenger leaves the vehicle while holding the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1. In this situation, the following control is performed:

          Possible Effects without Warning Engine cannot be restarted.
          Warning Active Condition

          The warning is activated when all of the following conditions are met:


          • The engine switch is on (ACC) or on (IG).

          • A door other than the driver door is opened → closed.

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is not detected in the vehicle (interior key certification fails).

          • The vehicle speed is not detected.
          Warning Method Combination Meter Assembly Multi Buzzer Sounds once
          Multi-information Display

          The following warning message is displayed:


          • Key Not Detected Check Key Location
          Advisory Display -
          Wireless Door Lock Buzzer Sounds 3 times*2
          Warning Stop Condition

          The warning is stopped when either of the following conditions is met:


          • The engine switch is turned off.

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is detected in the vehicle (interior key certification result is OK).

          • *1: Models with card key

          • *2: Except models for China

      5. Situation D


        • When the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is not in the vehicle, the driver attempts to turn the engine switch on (IG) (emergency key operation*2 is included). In this situation, the following control is performed:

          Possible Effects without Warning User becomes confused
          Warning Active Condition

          The warning is activated when all of the following conditions are met:


          • The immobiliser system is set.

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is not in the vehicle (interior key certification fails and transponder certification fails).

          • No records of unlock operation using a mechanical key and key certification failure when the engine switch was turned on (IG).
          Warning Method Combination Meter Assembly Multi Buzzer Sounds once
          Multi-information Display

          The following warning message is displayed:


          • Key Not Detected Check Key Location
          Advisory Display -
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The warning is stopped when one of the following conditions is met:


          • 15 seconds elapse.

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is detected in the vehicle (interior key certification result is OK and transponder certification result is OK).

          • 30 seconds have elapsed since a door was opened using a outside door handle.

          Tech Tips

          *1: Models with card key

          *2: Emergency key operation is an operation that changes the power source by touching the engine switch with the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly.

      6. Situation E


        • The vehicle starts moving without a registered electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* in the vehicle. In this situation, the following control is performed:

          Possible Effects without Warning Engine cannot be restarted.
          Warning Active Condition

          The warning is activated when all of the following conditions are met:


          • The engine switch is on (IG).

          • The warning is activated in situation C.

          • The vehicle speed is above 5 km/h (3 mph).

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* is not detected in the vehicle (interior key certification fails).
          Warning Method Combination Meter Assembly Multi Buzzer Sounds 9 times
          Multi-information Display

          The following warning message is displayed:


          • Key Not Detected Check Key Location
          Advisory Display -
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The warning is stopped when either of the following conditions is met:


          • The engine switch is turned off.

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* is detected in the vehicle (interior key certification result is OK).

          • *: Models with card key

      7. Situation F


        • The lock sensor on a outside door handle is touched to perform entry lock with the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 left in the vehicle. In this situation, the following control is performed:

          Possible Effects without Warning Vehicle theft
          Warning Active Condition

          The warning is activated when all of the following conditions are met:


          • The engine switch is off.

          • All doors are closed.

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is detected in the vehicle (interior key certification result is OK).

          • The lock sensor on the outer door handle is on (touched).

          • Any door is unlocked.

          • The vehicle speed is not detected.
          Warning Method Combination Meter Assembly Multi Buzzer -
          Multi-information Display

          The following warning message is displayed:


          • Key Left inside Vehicle
          Advisory Display -
          Wireless Door Lock Buzzer Sounds continuously*2
          Wireless Door Lock Buzzer Warning Stop Condition

          The warning is stopped when any of the following conditions is met:


          • 5 seconds elapse.

          • The engine switch is turned on (ACC) or on (IG).

          • The vehicle speed is above 5 km/h (3 mph).

          • Any door is opened.

          • Lock operation is detected.
          "Key detected in vehicle" Message Warning Stop Condition

          The warning is stopped when any of the following conditions is met:


          • 60 seconds elapse.

          • The engine switch is turned on (ACC) or on (IG).

          • The vehicle speed is above 5 km/h (3 mph).

          • Lock operation is detected.

          • *1: Models with card key

          • *2: Except models for China

      8. Situation G (Except Models for China)


        • The lock sensor on the outside door handle is pushed to perform entry lock, however, a door is ajar. In this situation, the following control is performed:

          Possible Effects without Warning Vehicle theft
          Warning Active Condition

          The warning is activated when all of the following conditions are met:


          • The engine switch is off.

          • Any door is open other than the door where the entry lock operation is performed.

          • The lock sensor on the outer door handle is on (touched), the lock button on the electrical key transmitter sub-assembly or the back door lock switch is pressed.

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is in an outside detection area (exterior key certification result is OK).
          Warning Method Combination Meter Assembly Multi Buzzer -
          Multi-information Display -
          Advisory Display -
          Wireless Door Lock Buzzer Sounds continuously*2
          Warning Stop Condition

          The warning is stopped when one of the following conditions is met:


          • 5 seconds elapse.

          • The engine switch is turned on (ACC) or on (IG).

          • All doors are closed.

          • Unlock operation is performed using the wireless door lock remote function.

          • Unlock operation is performed using the touch sensor on the inside of an outer door handle.

          • *1: Models with card key

          • *2: Except models for China

      9. Situation H


        • The door is locked with the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 left in the vehicle. In this situation, the following control is performed:

          Possible Effects without Warning Vehicle theft
          Warning Active Condition

          Condition 1

          The warning is activated when all of the following conditions are met:


          • The door is locked using the keyless lock operation.*2

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is in the vehicle (interior key certification result is OK).

          • The vehicle speed is not detected.

          Condition 2

          The warning is activated when all of the following conditions are met (Models compliant with Thatcham only):


          • The engine switch is turned off.

          • All doors are closed and locked.

          • Lock operation without using the entry system is detected.

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is in the vehicle (interior key certification result is OK).
          Warning Method Combination Meter Assembly Multi Buzzer Sounds once
          Multi-information Display

          The following warning message is displayed:


          • Key Left inside Vehicle
          Advisory Display -
          Wireless Door Lock Buzzer Sounds continuously*3
          Wireless Door Lock Buzzer Warning Stop Condition

          The warning is stopped when one of the following conditions is met:


          • 5 seconds elapse.

          • The engine switch is turned to other mode.

          • Any door is opened.

          • Lock operation is detected.

          • The vehicle speed is above 5 km/h (3 mph).
          "Key Left inside Vehicle" Message Warning Stop Condition

          The warning is stopped when one of the following conditions is met:


          • 60 seconds elapse.

          • The engine switch is turned to another mode.

          • Lock operation is detected.

          • The vehicle speed is above 5 km/h (3 mph).

          Tech Tips

          *1: Models with card key

          *2: Keyless lock operation is door lock operation without using the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly. First, set the lock position (door lock knob) when the door is open, and close the door while pulling the door handle to lock the door.

          *3: Except models for China

      10. Situation I


        • The vehicle is driven using an electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 that has a low battery. In this situation, the following control is performed:

          Possible Effects without Warning Usability function, engine cannot be restarted
          Warning Active Condition

          Condition 1

          The warning is activated when all of the following conditions are met:


          • The engine switch is turned off after being left on (IG) for more than 20 minutes.

          • The key battery voltage is low (key battery low code is received).

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is in the vehicle (interior key certification result is OK).

          • The vehicle speed is not detected.

          Condition 2

          The warning is activated when all of the following conditions are met:


          • The engine is stopped → restarted (engine speed is 500 rpm or more).

          • The key battery voltage is low (key battery low code is received).

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is in the vehicle (interior key certification result is OK).

          • The vehicle speed is not detected.

          • The low key battery warning for condition 1 was performed.*2
          Warning Method Combination Meter Assembly Multi Buzzer Sounds once
          Multi-information Display

          The following warning message is displayed:


          • Key Battery Low
          Advisory Display -
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The warning is stopped when either of the following conditions is met:


          • 15 seconds elapse.

          • The vehicle speed is above 5 km/h (3 mph).

          • *1: Models with card key

          • *2: Warning performed after 20 minutes of the engine switch being turned on (IG)

      11. Situation J


        • The steering lock cannot be released or the shift lever is moved to a position other than P before the steering lock is unlocked. In this situation, the following control is performed:

          Possible Effects without Warning Usability function
          Warning Active Condition

          The warning is activated when the following condition is met:

          The steering lock cannot be released (the steering lock ECU judgment).
          Warning Method Combination Meter Assembly Multi Buzzer Sounds once
          Multi-information Display

          The following warning message is displayed:


          • Steering Wheel Lock Press Engine Switch while Turning Wheel
          Advisory Display -
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The engine switch is pushed while the steering wheel is turned left and right.

          The warning is stopped when either of the following conditions is met:


          • 15 seconds elapse.

          • The steering lock is released.

      12. Situation K


        • A vehicle speed signal malfunction or malfunction that interferes with steering lock ECU (steering lock actuator assembly) operation has been detected. In this situation, the following control is performed:

          Possible Effects without Warning Malfunction Detection
          Warning Active Condition

          The warning is activated when either of the following conditions is met:


          • The steering lock ECU (steering lock actuator assembly) or steering lock/unlock position switch is malfunctioning.

          • The vehicle speed is judged as abnormal or vehicle speed signal communication is malfunctioning.
          Warning Method Combination Meter Assembly Multi Buzzer Sounds once
          Multi-information Display

          The following warning message is displayed:


          • Smart Entry & Start System Malfunction See Owner's Manual
          Advisory Display -
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The warning is stopped when either of the following conditions is met:


          • 15 seconds elapse.

          • The system returns to normal.

      13. Situation L


        • When the driver attempts to start the engine after unlocking the driver door using the mechanical key, the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* cannot be detected in the vehicle or cannot be detected in the vehicle 2 times in a row. In this situation, the following control is performed:

          Possible Effects without Warning Usability function
          Warning Active Condition

          The warning is activated when the engine switch is pressed with all of the following conditions met:


          • The immobiliser system is set.

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* is not detected in the vehicle (interior key certification fails).

          • The doors were unlocked using a mechanical key or when the engine switch is pressed, a certification error occurs 2 times in a row.
          Warning Method Combination Meter Assembly Multi Buzzer Sounds once
          Multi-information Display

          The following warning message is displayed for 60 seconds (and then automatically turned off):


          • Depress Brake and Then Touch Key to Engine Switch
          Advisory Display -
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The warning is stopped when one of the following conditions is met:


          • 60 seconds elapse.

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* is detected in the vehicle (interior key certification result is OK and transponder certification result is OK).

          • 30 seconds have elapsed since the door was opened using a outside door handle.

          • *: Models with card key

      14. Situation M


        • The engine switch is touched with an electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* when the transmitter battery voltage is low, smart operation is canceled or radio interference occurs. In this situation, the following control is performed:

          Possible Effects without Warning Usability function
          Warning Active Condition Transponder certification result is OK.
          Warning Method Combination Meter Assembly Multi Buzzer Sounds once
          Multi-information Display

          The following warning message is displayed:


          • Depress Brake and Then Start Engine
          Advisory Display -
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The warning is stopped when one of the following conditions is met:


          • 10 seconds elapse.

          • The electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* is detected in the vehicle (interior key certification results is OK).

          • The engine is running at 500 r/min or more.

          • The engine is started.

          • The immobiliser system is set and interior certification is stopped or key certification fails.

          • *: Models with card key

      15. Situation N


        • The system recognizes the situation that indicates the driver may start the engine (when the driver enters the vehicle or the engine switch is on (ACC)). In this situation, the following control is performed:

          Possible Effects without Warning Engine cannot be restarted
          Warning Active Condition

          The warning is activated when either of the following conditions is met:


          • When the door is unlocked from the outside of the vehicle with the engine switch off, the driver door is closed → opened.

          • Each time the power source mode is changed from off to on (ACC) without the brake pedal depressed.
          Warning Method Combination Meter Assembly Multi Buzzer -
          Multi-information Display

          The following warning message is displayed:


          • Depress Brake and Then Start Engine
          Advisory Display -
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The warning is stopped when one of the following conditions is met:


          • 20 seconds have elapsed since the warning started.

          • The engine is started.

          • Door lock operation is performed from the outside of the vehicle.

          • Wireless operation is performed from the inside of the vehicle or door lock operation is performed using a keyless lock function.

      16. Situation O


        • The system recognizes the situation that indicates the driver may start the engine (when the engine switch is on (IG)). In this situation, the following control is performed:

          Possible Effects without Warning Engine cannot be restarted
          Warning Active Condition

          The warning is activated when either of the following conditions is met:


          • Each time the power source mode is changed from off to on (IG) (the engine is not started) with the shift lever in P and without the brake pedal depressed.

          • When the engine switch is on (IG) (the engine is not started) with the shift lever in a position other than P, the shift lever is moved to P.
          Warning Method Combination Meter Assembly Multi Buzzer -
          Multi-information Display

          The following warning message is displayed:


          • Depress Brake and Then Start Engine
          Advisory Display -
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The warning is stopped when one of the following conditions is met:


          • The power source mode is changed to any mode other than on (IG).

          • The vehicle speed is above 5 km/h (3 mph).

          • The shift lever is in a position other than P or N.

      17. Situation P


        • The driver attempts to turn the engine switch off with the shift lever in any position other than P or N. In this situation, the following control is performed:

          Possible Effects without Warning Discharged vehicle battery, vehicle roll-away.
          Warning Active Condition The engine switch is turned off when the shift lever in a position other than P or N. (Excluding an emergency stop by pressing the engine switch 3 times quickly or pressing and holding the engine switch for 2 seconds or more.)
          Warning Method Combination Meter Assembly Multi Buzzer Sounds once
          Multi-information Display

          The following warning message is displayed:


          • Shift to P Before Exiting Vehicle
          Advisory Display -
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The warning is stopped when either of the following conditions is met:


          • The shift lever is moved to P.

          • The engine switch is turned to a mode other than on (ACC).

      18. Situation Q


        • Under situation P, the shift lever is moved to P. In this situation, the following control is performed:

          Possible Effects without Warning Discharged vehicle battery, vehicle roll-away (vehicle creep, such as when N is selected)
          Warning Active Condition The shift lever is moved to P.
          Warning Method Combination Meter Assembly Multi Buzzer Sounds once
          Multi-information Display

          The following warning message is displayed:


          • Turn Off Vehicle
          Advisory Display -
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The warning is stopped when either of the following conditions is met:


          • The power source mode is changed to a mode other than on (ACC).

          • The shift lever is in any position other than P.

      19. Situation R


        • Automatic power off operation occurs. In this situation, the following control is performed:

          Possible Effects without Warning Usability function
          Warning Active Condition

          The warning is activated when all of the following conditions are met:


          • The shift lever is in P.

          • The engine switch is on (ACC) or on (IG).

          • The vehicle speed is not detected and the engine is stopped.

          • The power source is turned off by the automatic power off function (the vehicle remains not operated for 20 minutes with the engine switch on (ACC) or for 1 hour with the engine switch on (IG)).
          Warning Method Combination Meter Assembly Multi Buzzer -
          Multi-information Display

          The following warning message is displayed:


          • Power Turned Off to Save Battery
          Advisory Display -
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The warning is stopped when either of the following conditions is met:


          • 10 seconds have elapsed since the warning started.

          • The engine switch is turned on (ACC) or on (IG).

      20. Situation S


        • The driver stopped the engine using emergency operation while driving. In this situation, the following control is performed:

          Possible Effects without Warning Usability function
          Warning Active Condition

          The warning is activated when either of the following conditions is met:


          • The engine is stopped by emergency stop operation while driving.

          • After emergency stop operation, the engine switch is turned on (IG), the vehicle speed is detected and the engine is not started.
          Warning Method Combination Meter Assembly Multi Buzzer Sounds continuously
          Multi-information Display

          The following warning message is displayed:


          • Shift to N and Press Engine Switch to Restart
          Advisory Display -
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The warning is stopped when one of the following conditions is met:


          • The shift lever is moved to P.

          • The vehicle speed is not detected (after the engine switch is turned on (IG) using engine switch operation).

          • The engine switch is operated.

          • The engine has started.

      21. Situation T


        • The driver pressed the engine switch while driving. In this situation, the following control is performed:

          Possible Effects without Warning Wrong operation is prevented
          Warning Active Condition The vehicle is moving, the vehicle speed is detected and the engine switch is pressed.
          Warning Method Combination Meter Assembly Multi Buzzer Sounds intermittently
          Multi-information Display -
          Advisory Display -
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The warning is stopped when either of the following conditions is met:


          • 2 seconds have elapsed since the engine switch operation was stopped.

          • The engine switch is turned off.

      22. Situation U


        • The driver pressed the engine switch while driving. In this situation, the following control is performed:

          Possible Effects without Warning Usability function
          Warning Active Condition The vehicle is moving, the vehicle speed is detected and the engine switch is pressed.
          Warning Method Combination Meter Assembly Multi Buzzer Sounds once
          Multi-information Display

          The following warning message is displayed:


          • Push and Hold Engine Switch for Emergency Stop
          Advisory Display -
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The warning is stopped when either of the following conditions is met:


          • 10 seconds elapse.

          • The engine switch is turned off.

      23. Situation V


        • The power source is changed to on (ACC). In this situation, the following control is performed:

          Possible Effects without Warning Usability function
          Warning Active Condition The power source is changed to on (ACC).
          Warning Method Combination Meter Assembly Multi Buzzer -
          Multi-information Display -
          Advisory Display ACCESSORY
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The warning is stopped when the following condition is met:


          • The power source is changed to a mode other than on (ACC).

      24. Situation W


        • The power source is changed to on (IG). In this situation, the following control is performed:

          Possible Effects without Warning Usability function
          Warning Active Condition The power source is changed to on (IG).
          Warning Method Combination Meter Assembly Multi Buzzer -
          Multi-information Display -
          Advisory Display IGNITION ON
          Wireless Door Lock Buzzer -
          Warning Stop Condition

          The warning is stopped when either of the following conditions is met:


          • The power source is changed to a mode other than on (IG).

          • The display in the odometer area is changed due to user operation.

    7. Battery Saving (Models with Entry Function)


      1. Battery saving preserves the vehicle and key batteries. It is activated when the vehicle remains parked for a long time and when the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* is left in the exterior actuation area.

        Condition Control Reinstatement Condition
        When the vehicle remains parked for a long time.

        Control 1:

        No response from electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* for more than 5 days


        • Door electrical key antennas and electrical key antenna stop emitting signals for creating the actuation area.

        		 When the engine switch is turned on (IG), the control is canceled and the system is returned to normal.

        Control 2:

        No response from electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* for more than 14 days


        • Door electrical key antennas and electrical key antenna stop emitting signals for creating the actuation area.

        • Door lock sensors and unlock sensors for seats other than the driver seat are disabled.

        When the engine switch is turned on (IG), the control is canceled and the system is returned to normal.

        When one of the following conditions is met, the control is returned to control 1:


        • The doors are locked or unlocked using wireless remote control.

        • The doors are locked or unlocked by touching the lock/unlock sensor on the driver door.

        • A door is locked or unlocked using the mechanical key.

        • Door is opened → closed.
        When the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* is left in the exterior detection area.

        This state continues longer than 10 minutes


        • Electrical key antenna that is detecting the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly* stops emitting signals for creating the actuation area.

        The control is stopped when one of the following conditions is met:


        • The doors are locked or unlocked using wireless remote control.

        • The doors are locked or unlocked by touching the lock/unlock sensor on the front or rear door.

        • A door is locked or unlocked using the mechanical key.

        • *: Models with card key

      2. In addition to the above functions, the auto power off function helps to reduce drain on the vehicle battery by turning the power source mode to off when approximately 60 minutes have elapsed since the shift lever was moved to P with the power source on (ACC), or the engine was turned off with the shift lever in P, the power source on (IG) and the vehicle stationary.

    8. Battery Saving Function of Electrical Key Transmitter Sub-assembly


      1. This function cancels the signal reception waiting state of the electrical key transmitter sub-assembly, reducing the consumption of current from its battery.

      2. The electrical key transmitter sub-assembly can be placed into and taken out of battery saving mode. When the electrical key transmitter sub-assembly is in battery saving mode, the entry and start system will not be able to detect the transmitter, as the transmitter will not respond to signals from the vehicle. The function of the entry and start system will not operate if the electrical key transmitter sub-assembly is in battery saving mode.

      3. Pressing the unlock button of the electrical key transmitter sub-assembly twice while pressing the lock button (the indicator light of the electrical key transmitter sub-assembly blinks 4 times) selects battery saving mode for the electrical key transmitter sub-assembly.

      4. Battery saving mode can be canceled by pressing any switch on the electrical key transmitter sub-assembly.

    9. Entry unlock mode switching function (Models with Entry Function)


      1. The following entry unlock modes can be selected when using the entry unlock mode switching function.


        • All door unlock mode: When the sensor of a outside door handle assembly is touched, an entry unlock operation is performed simultaneously for all doors.

        • Driver door unlock mode: When the sensor of the driver side outside door handle assembly is touched, an entry unlock operation is performed for the driver door only. If any other door handle is touched, an entry unlock operation is performed simultaneously for all doors.

      2. When customizing through manual operation:


        1. Turn the engine switch off.

        2. Check that the LED of the electrical key transmitter sub-assembly is not illuminated, and then press and hold the lock and unlock buttons of the electrical key transmitter sub-assembly for 5 seconds or more while the electrical key transmitter sub-assembly is in the actuation area.

        3. Check the current setting.

          Tech Tips


          • The mode changes from all door unlock mode to driver door unlock mode and then back to all door unlock mode.

          • The answer-back (wireless buzzer, buzzer in the combination meter assembly) operation for each mode is indicated in the table below.

          Currently Selected Mode Answer-back (Wireless Buzzer) Answer-back (Buzzer in Combination Meter Assembly)
          All door unlock mode Buzzer sounds twice (short beeps) Buzzer sounds once
          Driver door unlock mode Buzzer sounds 3 times (short beeps) Buzzer sounds once

        4. Release the lock and unlock buttons of the electrical key transmitter sub-assembly.

        5. Check that the LED of the electrical key transmitter sub-assembly is not illuminated, and then press and hold the lock and unlock buttons of the electrical key transmitter sub-assembly for 5 seconds or more to change the mode.

          Tech Tips

          Repeat the procedure as necessary to select the desired mode.

        6. Unlock the doors with the wireless operation, and then open any door.

          B002FB2E01

    10. Key Cancel


      1. The following system functions can be deactivated by using the key cancel procedure.


        • Entry Lock

        • Entry Unlock

        • Back Door Open

        • Prevention of Key Confinement

        • Warning

      2. The system functions can be deactivated by using the following key cancel procedure when the engine switch is off and the driver door is closed and unlocked.

        Key Cancel Procedure

        The procedure is as follows:


        • Press the unlock switch of the electrical key transmitter sub-assembly once.

        • Within 5 seconds of the step above, open the driver door (Driver Door: Close → Open).

        • Within 5 seconds of the step above, press the unlock switch of the electrical key transmitter sub-assembly twice.

        • Repeat close → open for the driver door twice* (Driver Door: Open → Close → Open → Close → Open).

        • Press the unlock switch of the electrical key transmitter sub-assembly twice.*

        • Repeat close → open for the driver door once* (Driver Door: Open → Close → Open).

        • Within 5 seconds of the step above, close the driver door.

        When the cancel procedure is complete, the buzzer sounds twice. Meanwhile, when the procedure is performed again to resume the system, the buzzer sounds once.

        Tech Tips

        *: Perform all these 3 steps within 30 seconds of the previous step.

    11. Key Code Registration Function


      1. The table below shows the 3 special ID code registration function modes through which up to 7 different transmitter recognition codes can be registered. For details, refer to the Repair Manual.

        Mode Function
        Rewrite Clears all previously registered codes and registers only the newly received codes. This mode is used whenever the certification ECU (smart key ECU assembly) is replaced.
        Add Adds a newly received code while preserving previously registered codes. This mode is used when adding a new transmitter.
        Confirm Confirms how many codes are currently registered. When adding a new code, this mode is used to check how many codes already exist.

  4. FUNCTION


    1. Entry Function (Models with Entry Function)


      1. The entry function consists of the following functions:

        Function Outline
        Wireless Door Lock Control This function is a convenient system for locking and unlocking all the doors at a distance. The operation of this function is the same as that in the wireless door lock control system.
        Entry Illumination When an electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 enters the exterior actuation area of the door electrical key antennas, the interior light illuminates.
        Entry Unlock When an electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is located in the exterior actuation area of any door electrical key antenna, the door will unlock after the inner part of an outside door handle is touched.
        Entry Unlock Mode Switching

        Allows switching between 2 modes that can be operated with the entry unlock function.


        • Driver Door Mode

        • All Door Mode
        Entry Lock When an electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is located in the exterior actuation area of an electrical key antenna and the engine switch is off, all doors can be locked by simply touching the lock sensor or back door lock switch.
        Entry Back Door Unlock

        • The back door is unlocked by pressing the back door unlock switch of the back door.

        • The back door is unlocked and opened by performing the touchless kick actuation operation.*2
        Power Back Door Close and Lock*3 The back door is closed and then locked all doors by pressing the power back door close and lock switch.
        Prevention of Key Confinement The key confinement prevention function prevents the vehicle from being locked with an electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 left inside it. This function operates in 2 different situations: when the lock knob is used (keyless lock) and when an outside door handle lock sensor is used (lock sensor).
        Warning

        When any of the situations below occur, the entry and start system causes the certification ECU (smart key ECU assembly) to sound the multi buzzer in the combination meter and the wireless door lock buzzer*4, and indicates a warning on the multi-information display in order to alert the driver.


        • An exit warning is activated if the shift lever is in any position other than P.

        • An exit warning is activated if the shift lever is in P and the engine switch is in a mode other than off.

        • A warning is activated if the occupant leaves with the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 in inappropriate circumstances.

        • A warning is activated if the engine switch is operated while the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 is outside the actuation area.

        • A warning is activated if the lock button is operated while the electrical key transmitter sub-assembly is inside the vehicle.

        • A warning is activated if the key battery is weak.
        Battery Saving To prevent the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 battery and the vehicle battery from becoming discharged, the battery saving function activates when the vehicle remains unused for a long period of time or the electrical key transmitter sub-assembly or electrical key (card key) transmitter sub-assembly*1 has been detected in the exterior actuation area for more than 10 minutes.
        Key Cancel

        The following key functions can be canceled by following the specified procedure.


        • Entry unlock/lock

        • Back door open

        • Prevention of key confinement

        • Warning
        Key Code Registration A total of 7 electrical key transmitter sub-assemblies can be registered.

        *1: Models with card key

        *2: Models with hands free power back door

        *3: Models with power back door system

        *4: Except models for China

    2. Wireless Door Lock Control Function


      1. The wireless door lock control system has the following functions:

        Function Outline
        All Doors Lock Pressing the lock button of the electrical key transmitter sub-assembly locks all doors.
        All Doors Unlock (2-step Unlock) Pressing the unlock button of the electrical key transmitter sub-assembly twice within 5 seconds unlocks all doors after it first unlocks the driver's door.
        All Doors Unlock (1-step Unlock) Pressing the unlock button of the electrical key transmitter sub-assembly once unlocks all doors.
        Power Back Door Open or Close*1 Pressing the power back door button for approximately 1 second opens and closes the power back door.
        Answer Back When the doors are being locked or unlocked using the electrical key transmitter sub-assembly, the wireless door lock buzzer sounds*2 and the hazard warning lights blink once while locking and twice while unlocking. Also, the answer back function operates when the doors are locked by the automatic relock function.
        Panic Alarm*3

        Keeping the panic switch of the electrical key transmitter sub-assembly pushed longer than about 1 second causes the following to activate as an alarm:


        • The vehicle horn sounds.

        • The hazard lights, headlights and taillights flash.

        • The interior lights are illuminated (if the interior light switch is in the DOOR position).
        Automatic Relock If none of the doors are opened within 30 seconds after they are unlocked using the wireless door lock remote control, all the doors will be locked again automatically.
        Repeat If a door is not locked in response to the locking operation of the electrical key transmitter sub-assembly, the main body ECU (multiplex network body ECU) will output a lock signal again after 1 second elapses.
        Security Sends a door lock/unlock operation request signal as a rolling code.
        Door Ajar Warning*4 If any door is open or ajar, pushing the lock button of the electrical key transmitter sub-assembly will cause the wireless door lock buzzer to sound for about 5 seconds as a warning.

        *1: Models with power back door system

        *2: Models with wireless door lock buzzer answer back function

        *3: Models with panic alarm function

        *4: Except models for China

  5. DIAGNOSIS


    1. Start Function


      1. The certification ECU (smart key ECU assembly) can detect malfunctions in the entry and start system when the power source is on (IG).

      2. When the ECU detects a malfunction, a message is displayed on the multi-information display to warn the driver. At the same time, the ECU stores a 5-digit Diagnostic Trouble Code (DTC) in its memory.

      3. The indicator light warning continues for 15 seconds even after the engine switch is turned off.

      4. The 5-digit DTCs can be read after connecting the Global TechStream (GTS) to the DLC3.

      5. The entry and start system may not operate successfully if a malfunction occurs.