POWER WINDOW CONTROL SYSTEM(for Models with Jam Protection Function on Driver Door Window Only) OPERATION CHECK

  1. CHECK WINDOW LOCK SWITCH

    Tip:

    Before performing the window lock switch operation check, make sure that the window lock switch is off (the switch is not pushed in).

    B140183

    1. Check that the front passenger and rear windows* cannot be operated when the window lock switch of the power window regulator master switch assembly is pushed in.

      OK

      Front passenger and rear windows* are disabled.

      *: w/ Rear Power Window

    2. Check that the front passenger and rear windows* can be operated when the window lock switch of the power window regulator master switch assembly is pushed in again.

      OK

      Front passenger and rear windows* operate normally.

      *: w/ Rear Power Window

  2. CHECK MANUAL UP / DOWN FUNCTION

    1. Check that the driver door power window operates as follows:

      Table 1. OK

      Condition

      Master Switch

      Switch Operation

      Power Window

      Ignition switch ON

      Driver door

      Pulled halfway up

      UP (Closes)

      Pushed halfway down

      DOWN (Opens)

    2. Check that the front passenger door window and rear power windows* operate as follows:

      Table 2. OK

      Condition

      Regulator Switch

      Switch Operation

      Power Window

      • Ignition switch ON

      • Window lock switch off

      Front passenger door

      Pulled up

      UP (Closes)

      Pushed down

      DOWN (Opens)

      Rear LH door*

      Pulled up

      UP (Closes)

      Pushed down

      DOWN (Opens)

      Rear RH door*

      Pulled up

      UP (Closes)

      Pushed down

      DOWN (Opens)

      *: w/ Rear Power Window

  3. CHECK AUTO UP / DOWN FUNCTION

    1. Check that the driver door power window operates as follows:

      Table 3. OK

      Condition

      Master Switch

      Switch Operation

      Power Window

      Ignition switch ON

      Driver door

      Pulled up (One touch operation)

      AUTO UP (Closes)

      Pushed down (One touch operation)

      AUTO DOWN (Opens)

  4. CHECK REMOTE MANUAL UP / DOWN FUNCTION

    1. Check that the front passenger door window and rear power windows* operate as follows:

      Table 4. OK

      Condition

      Master Switch

      Switch Operation

      Power Window

      • Ignition switch ON

      • Window lock switch off

      Front passenger door

      Pulled up

      UP (Closes)

      Pushed down

      DOWN (Opens)

      Rear LH door*

      Pulled up

      UP (Closes)

      Pushed down

      DOWN (Opens)

      Rear RH door*

      Pulled up

      UP (Closes)

      Pushed down

      DOWN (Opens)

      *: w/ Rear Power Window

  5. CHECK POWER WINDOW OPERATION FUNCTION AFTER IGNITION SWITCH IS TURNED OFF

    1. Check that each power window can be operated with the power widow regulator master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly* after the ignition switch is turned off.

      Tip:

      If the window lock switch is on, the power windows cannot be operated except the driver door power window. Therefore, turn the window lock switch off before checking the window operation.

      *: w/ Rear Power Window

    2. Check that the key-off operation function does not operate immediately after the driver door or front passenger door is opened.

      Tip:

      Even if the driver door or front passenger door is opened during auto window operation while the key-off operation function is on, the window will continue operating.

    3. Check that all the power windows cannot be operated after more than approximately 43 seconds have elapsed since the ignition switch was turned off.

  6. CHECK JAM PROTECTION FUNCTION

    1. Check the basic function.

      CAUTION:

      Do not put your fingers between the door frame and door glass to check the jam protection function. Also, prevent any part of your body from being caught during inspection.

      Tip:

      The jam protection function is operative during both the auto up and manual up operations while the engine is running or the ignition switch is ON, and also for approximately 43 seconds after the ignition switch is turned off.

      1. Fully open the driver door window.

      2. B274528C08

        *a

        Check Jig

        *b

        Cloth

        Set a check jig wrapped with a piece of cloth near the window fully closed position.

      3. Operate the auto up or manual up function to check that the power window stops and goes down after the check jig is caught between the window and door frame, and stops when the opening reaches approximately 200 mm (7.87 in.) or approximately 5 seconds have elapsed.

        Tip:

        If the check jig is caught when the opening is approximately 75 mm (2.95 in.) or more, the power window goes down for approximately 125 mm (4.93 in.) or until approximately 2.5 seconds elapse.

      4. While the power window is moving down, check that the door glass cannot be raised using the power window switch.

  7. CHECK POWER WINDOW REGULATOR MASTER SWITCH LED ILLUMINATION

    1. Check the LED illumination (power window regulator master switch assembly).

      1. Check that the LED located in the power window regulator master switch assembly illuminates when the ignition switch is turned to ON.