OIL AND OIL FILTER REPLACEMENT

CAUTION / NOTICE / HINT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash your skin thoroughly with soap or waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.

  • In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.

PROCEDURE


  1. REMOVE OIL FILTER ELEMENT SERVICE HOLE COVER


    1. B005ZPP

      Remove the 3 clips.

    2. B005Y15

      Pull the oil filter element service hole cover to open it.

      Tech Tips

      Fully open the service hole cover and fold it at a 180° angle.

    3. B005YNOE01
      Text in Illustration
      *1 Clip

      Using one of the removed clips, secure the service hole cover with it folded at a 180° angle.

  2. DRAIN ENGINE OIL


    1. Remove the oil filler cap.

    2. Remove the oil pan drain plug and gasket, and drain the oil into a container.

    3. Clean and install the oil pan drain plug with a new gasket.

      Torque:
      37 N*m  { 377 kgf*cm, 27 ft.*lbf }

  3. REMOVE OIL FILTER


    1. for Oil Filter Sub-assembly Type:


      1. Using SST, remove the oil filter sub-assembly.

        SST
        09228-06502

    2. for Oil Filter Element Kit Type:


      1. B005ZIIC08
        *1 Cap Rib
        *2 Oil Filter Bracket Clip

        Using SST, loosen the oil filter cap 4 revolutions, align the cap ribs vertically, and drain the remaining engine oil in the oil filter cap.

        SST
        09228-06502

        Note

        Do not remove the oil filter bracket clip when removing the oil filter cap assembly.

        Tech Tips

        Set a container below the oil filter cap assembly before loosening the oil filter cap.

      2. Remove the oil filter cap assembly.

      3. B005YE9C08
        *1 Oil Filter Element
        *2 O-ring

        Remove the oil filter element and O-ring from the oil filter cap.

        Note

        Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring on the cap.

  4. INSTALL OIL FILTER


    1. for Oil Filter Sub-assembly Type:


      1. Check and clean the oil filter sub-assembly installation surface.

      2. Apply clean engine oil to the gasket of a new oil filter sub-assembly.

      3. Lightly screw the oil filter sub-assembly into place by hand. Tighten it until the gasket contacts the seat.

      4. Using SST, tighten the oil filter sub-assembly.

        SST
        09228-06502

          Depending on the work space available, choose from the following:

        • If enough space is available, use a torque wrench to tighten the oil filter sub-assembly.

        Torque:
        17.5 N*m  { 178 kgf*cm, 13 ft.*lbf }

        • If not enough space is available to use a torque wrench, tighten the oil filter sub-assembly 3/4 of a turn by hand or use a common wrench.

    2. for Oil Filter Element Kit Type:


      1. Clean the oil filter cap threads and O-ring groove.

      2. Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.

      3. Set a new oil filter element in the oil filter cap.

      4. Remove any dirt or foreign matter from the installation surface and inside of the engine.

      5. B005ZTN

        Reapply a small amount of engine oil to the O-ring of the oil filter cap assembly. Align the cutout in the oil filter cap threads 90° to the grooves in the oil filter bracket and temporarily tighten the cap.

        Note

        Make sure that the O-ring does not get caught between the parts.

      6. B005ZU6C04
        *1 Oil Filter Bracket Clip
        *a No Clearance

        Using SST, tighten the oil filter cap assembly.

        SST
        09228-06502
        Torque:
        25 N*m  { 255 kgf*cm, 18 ft.*lbf }

        Note


        • After tightening the oil filter cap assembly, check for gaps between the installation surfaces.

        • Do not remove the oil filter bracket clip when installing the oil filter cap assembly.

        • Do not cross thread the oil filter cap assembly.

  5. ADD ENGINE OIL


    1. Add new engine oil and install the oil filler cap.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)
      API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil

      • 0W-20


      • 5W-20


      • 5W-30


      • 10W-30
      API grade SL, SM or SN multigrade engine oil

      • 15W-40


      • 20W-50
      Standard Capacity
      Item Standard Condition
      Drain and refill with oil filter change 4.2 liters (4.4 US qts, 3.7 lmp. qts)
      Drain and refill without oil filter change 3.9 liters (4.1 US qts, 3.4 lmp. qts)
      Dry fill 4.7 liters (5.0 US qts, 4.1 lmp. qts)

  6. INSPECT FOR ENGINE OIL LEAK


    1. Put the engine in inspection mode Click here.

    2. Start the engine.

    3. Check for engine oil leaks from the oil filter cap and oil pan drain plug.

  7. INSTALL OIL FILTER ELEMENT SERVICE HOLE COVER


    1. B005YNOE01
      Text in Illustration
      *1 Clip

      Remove the clip.

    2. B005ZM0

      Close the service hole cover.

      Tech Tips


      • Push the oil filter element service hole cover towards the vehicle to remove the crease.

      • If the crease remains, the service hole cover may look as though it does not fit properly after the clips are installed.

    3. B005ZPP

      Install the oil filter element service hole cover with the 3 clips.