REAR DOOR LOCK INSPECTION

PROCEDURE

1. INSPECT REAR DOOR LOCK ASSEMBLY LH (w/o Double Locking System)

   

   1. Check the door lock motor operation.

      1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

         OK

         Measurement Condition	Specified Condition
         Battery positive (+) → 4 (L) Battery negative (-) → 1 (UL)	Lock
         Battery positive (+) → 1 (UL) Battery negative (-) → 4 (L)	Unlock

         • If the result is not as specified, replace the door lock assembly.

   2. Check the detection switch.

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         6 (LSSR) - 9 (E)	Unlock	Below 1 Ω
         6 (LSSR) - 9 (E)	Lock	10 kΩ or higher

         • If the result is not as specified, replace the door lock assembly.

2. INSPECT REAR DOOR LOCK ASSEMBLY LH (w/ Double Locking System)

   

   1. Check the door lock motor operation.

      1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

         OK

         Measurement Condition	Specified Condition
         Battery positive (+) → 2 (L) Battery negative (-) → 1 (UL)	Lock
         Battery positive (+) → 1 (UL) Battery negative (-) → 2 (L)	Unlock
         Battery positive (+) → 4 (DL) Battery negative (-) → 3 (UNDL)	Set
         Battery positive (+) → 3 (UNDL) Battery negative (-) → 4 (DL)	Unset

         • If the result is not as specified, replace the door lock assembly.

   2. Check the detection switch.

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         5 (LSSR) - 6 (E)	Unlock	Below 1 Ω
         5 (LSSR) - 6 (E)	Lock	10 kΩ or higher

         • If the result is not as specified, replace the door lock assembly.

3. INSPECT REAR DOOR LOCK ASSEMBLY RH (w/o Double Locking System)

   

   1. Check the door lock motor operation.

      1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

         OK

         Measurement Condition	Specified Condition
         Battery positive (+) → 4 (L) Battery negative (-) → 1 (UL)	Lock
         Battery positive (+) → 1 (UL) Battery negative (-) → 4 (L)	Unlock

         • If the result is not as specified, replace the door lock assembly.

   2. Check the detection switch.

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         6 (LSSR) - 9 (E)	Unlock	Below 1 Ω
         6 (LSSR) - 9 (E)	Lock	10 kΩ or higher

         • If the result is not as specified, replace the door lock assembly.

4. INSPECT REAR DOOR LOCK ASSEMBLY RH (w/ Double Locking System)

   

   1. Check the door lock motor operation.

      1. Apply battery voltage to the door lock motor connector and check the operation of the door lock motor.

         OK

         Measurement Condition	Specified Condition
         Battery positive (+) → 4 (L) Battery negative (-) → 3 (UL)	Lock
         Battery positive (+) → 3 (UL) Battery negative (-) → 4 (L)	Unlock
         Battery positive (+) → 2 (DL) Battery negative (-) → 1 (UNDL)	Set
         Battery positive (+) → 1 (UNDL) Battery negative (-) → 2 (DL)	Unset

         • If the result is not as specified, replace the door lock assembly.

   2. Check the detection switch.

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance

         Tester Connection	Condition	Specified Condition
         9 (LSSR) - 10 (E)	Unlock	Below 1 Ω
         9 (LSSR) - 10 (E)	Lock	10 kΩ or higher

         • If the result is not as specified, replace the door lock assembly.