AUTOMATIC TRANSMISSION UNIT(for 2TR-FE) REASSEMBLY

PROCEDURE


  1. BEARING POSITION

    B0028UQN02
    Bearing and Race Diameter
    Mark Front Race Diameter Inside / Outside (mm (in.)) Thrust Bearing Diameter Inside / Outside (mm (in.)) Rear Race Diameter Inside / Outside (mm (in.))
    A 74.2 (2.921) / 87.74 (3.454) 71.9 (2.831) / 85.6 (3.370) -
    B 40.0 (1.575) / 52.8 (2.079) 34.6 (1.362) / 52.0 (2.047) -
    C 22.6 (0.866) / 44.8 (1.764) 21.3 (0.839) / 41.1 (1.618) -
    D 38.4 (1.512) / 56.5 (2.224) 33.3 (1.311) / 56.6 (2.228) -
    E - 40.83 (1.607) / 52.8 (2.079) 39.6 (1.559) / 52.8 (2.079)
    F - 37.1 (1.461) / 61.2 (2.409) 44.0 (1.732) / 62.8 (2.472)
    G 65.8 (2.591) / 86.3 (3.398) 63.3 (2.492) / 78.8 (3.102) -
    H 66.3 (2.610) / 78.9 (3.106) 63.3 (2.492) / 78.8 (3.102) -
    I - 55.7 (2.193) / 76.4 (3.008) 53.7 (2.114) / 74.0 (2.913)
    J 33.4 (1.315) / 49.0 (1.929) 32.1 (1.264) / 49.35 (1.943) 32.1 (1.264) / 49.0 (1.929)
    K - 21.0 (0.827) / 41.5 (1.634) 23.13 (0.911) / 41.5 (1.634)
    L - 43.55 (1.715) / 61.0 (2.402) 47.1 (1.854) / 67.1 (2.642)
    M 36.1 (1.421) / 52.5 (2.067) 37.0 (1.457) / 51.2 (2.016) 36.1 (1.421) / 51.0 (2.008)
  2. INSTALL BRAKE PLATE STOPPER SPRING


    1. B0028B7

      Install the 2 brake plate stopper springs to the automatic transmission case sub-assembly.

      Note

      The shapes of the parts are different. Refer to the illustration when installing the parts.

  3. INSTALL NO. 4 BRAKE PISTON


    1. Coat 2 new O-rings with ATF, and install them to the brake reaction sleeve.

    2. Coat 2 new O-rings with ATF, and install them to the No. 4 brake piston.

    3. B00281VC02
      *1 No. 4 Brake Piston
      *2 Brake Reaction Sleeve

      Install the No. 4 brake piston to the brake reaction sleeve.

      Note

      Be careful not to damage the O-rings.

  4. INSTALL BRAKE REACTION SLEEVE


    1. B0027EJC01
      *1 Brake Reaction Sleeve
      *2 No. 4 Brake Piston

      With the No. 4 brake piston underneath (the rear side), install the brake reaction sleeve and No. 4 brake piston to the automatic transmission case sub-assembly.

      Note

      Be careful not to damage the O-rings.

  5. INSTALL 1ST AND REVERSE BRAKE PISTON


    1. B00247T

      Coat a new O-ring with ATF, and install it to the 1st and reverse brake piston.

    2. Install the 1st and reverse brake piston to the automatic transmission case sub-assembly while making sure that the protrusion of the 1st and reverse brake piston is positioned as shown in the illustration.

      Note

      Be careful not to damage the O-ring.

    3. B0027KS

      Install the 1st and reverse brake return spring sub-assembly to the automatic transmission case sub-assembly.

    4. Place the 1st and reverse brake return spring sub-assembly onto the 1st and reverse brake piston.

    5. B00295GC01
      *a Protective Tape

      Place SST on the 1st and reverse brake return spring sub-assembly, and compress the 1st and reverse brake return spring sub-assembly.

      SST
      09380-60011   ( 09381-06030, 09381-05040, 09381-06040, 09381-06080, 09381-05050, 09381-06120, 09381-06130, 09381-06140 )
    6. Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.

      Note

      Be careful not to damage the 1st and reverse brake return spring sub-assembly and automatic transmission case sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

  6. INSTALL REAR PLANETARY GEAR ASSEMBLY


    1. B0026V7C01
      *1 Thrust Needle Roller Bearing K
      *2 Thrust Bearing Race K
      *3 Thrust Needle Roller Bearing L
      *4 Thrust Bearing Race L

      Coat the thrust bearing race with ATF and install it to the automatic transmission case sub-assembly.

      Thrust Needle Roller Bearing and Thrust Bearing Race Diameter
      Item Inside (mm (in.)) Outside (mm (in.))
      Thrust Needle Roller Bearing K 21.0 (0.827) 41.5 (1.634)
      Thrust Bearing Race K 23.13 (0.911) 41.5 (1.634)
      Thrust Needle Roller Bearing L 43.55 (1.715) 61.0 (2.402)
      Thrust Bearing Race L 47.1 (1.854) 67.1 (2.642)

      Note

      Be sure to install the thrust needle roller bearing and thrust bearing race in the correct direction.

    2. Coat the 2 thrust needle roller bearings and thrust bearing races with ATF and install them to the rear planetary gear assembly.

    3. Install the rear planetary gear assembly to the automatic transmission case sub-assembly.

    4. B00256VC01
      *1 Thrust Bearing Race M (Front Race)
      *2 Needle Roller Bearing M
      *3 Thrust Bearing Race M (Rear Race)

      Coat the thrust needle roller bearing and 2 thrust bearing races with ATF and install them to the output shaft of the rear planetary gear assembly.

      Bearing and Race Diameter
      Item Inside (mm (in.)) Outside (mm (in.))

      Thrust Bearing Race M

      (Front Race)

      36.1 (1.421) 52.5 (2.067)
      Thrust Needle Roller Bearing M 37.0 (1.457) 51.2 (2.016)

      Thrust Bearing Race M

      (Rear Race)

      36.1 (1.421) 51.0 (2.008)

      Note

      Be sure to install the thrust needle roller bearing and thrust bearing race in the correct direction.

    5. B0026XY

      Using a snap ring expander, install the snap ring.

    6. B0024UPC01
      *1 Thrust Bearing Race M (Rear Race)
      B0068O0 Mark Area

      Using a feeler gauge, measure the clearance between the snap ring and thrust bearing race.

      Standard clearance
      0.02 to 0.12 mm (0.000788 to 0.00472 in.)

      If the clearance is outside the standard range, select another thrust bearing race that brings the clearance within the standard range.

      Tech Tips

      There are 12 different thicknesses for the thrust bearing race.

      Race Thickness
      Part No. Mark Thickness
      35789-35060 B0025BN 3.80 mm (0.150 in.)
      35789-50070 B0025S2 3.85 mm (0.152 in.)
      35789-35070 B0025KE 3.90 mm (0.154 in.)
      35789-50080 B0026NK 3.95 mm (0.156 in.)
      35789-35080 B00251J 4.00 mm (0.157 in.)
      35789-50090 B0025G8 4.05 mm (0.159 in.)
      35789-35090 B00267J 4.10 mm (0.161 in.)
      35789-50100 B0025CK 4.15 mm (0.163 in.)
      35789-35100 B0024UG 4.20 mm (0.165 in.)
      35789-50110 B0027RZ 4.25 mm (0.167 in.)
      35789-50120 B0024A7 4.30 mm (0.169 in.)
      35789-50130 B0026HC 4.35 mm (0.171 in.)
  7. INSTALL NO. 4 BRAKE DISC


    1. B0025ZMC01
      *1 No. 4 Brake Flange
      *2 No. 4 Brake Disc
      *3 No. 4 Brake Plate

      Install the 2 No. 4 brake flanges, 5 No. 4 brake discs and 4 No. 4 brake plates to the automatic transmission case sub-assembly.

      Note


      • Make sure that the No. 4 brake discs, No. 4 brake plates and No. 4 brake flanges are installed in the correct order.

      • Install the thicker No. 4 brake flange first, and then install the thinner one.

  8. INSTALL INTERMEDIATE SHAFT


    1. B0025MHC01
      *1 Thrust Needle Roller Bearing J
      *2 Thrust Bearing Race J (Rear Race)

      Coat the thrust needle roller bearing and thrust bearing race with ATF and install them to the intermediate shaft.

      Thrust Needle Roller Bearing and Thrust Bearing Race Diameter
      Item Inside (mm (in.)) Outside (mm (in.))
      Thrust Needle Roller Bearing J 32.1 (1.264) 49.35 (1.943)

      Thrust Bearing Race J

      (Rear Race)

      32.1 (1.264) 49.0 (1.929)
    2. Install the intermediate shaft to the automatic transmission case sub-assembly.

  9. INSTALL REAR PLANETARY RING GEAR


    1. B0025GVC01
      *1 Rear Planetary Ring Gear Flange Sub-assembly
      *2 Rear Planetary Ring Gear

      Install the rear planetary ring gear to the rear planetary ring gear flange sub-assembly.

    2. B002705C01
      *a Protective Tape

      Using a screwdriver, install the snap ring to the rear planetary ring gear flange sub-assembly with rear planetary ring gear.

      Note

      Be careful not to damage the rear planetary ring gear flange sub-assembly with rear planetary ring gear.

      Tech Tips

      Tape the screwdriver tip before use.

  10. INSTALL REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY WITH REAR PLANETARY RING GEAR


    1. B0026F5C01
      *1 Thrust Bearing Race J (Front Race)

      Coat the thrust bearing race with ATF and install it to the rear planetary ring gear flange sub-assembly with rear planetary ring gear.

      Thrust Bearing Race Diameter
      Item Inside (mm (in.)) Outside (mm (in.))

      Thrust Bearing Race J

      (Front Race)

      33.4 (1.315.) 49.0 (1.929)

      Note

      Be sure to install the thrust bearing race in the correct direction.

    2. Install the rear planetary ring gear flange sub-assembly with rear planetary ring gear to the automatic transmission case sub-assembly.

  11. INSTALL ONE-WAY CLUTCH INNER RACE


    1. B0028Q1C01
      *1 One-way Clutch Inner Race
      *2 No. 3 One-way Clutch Assembly

      Install the one-way clutch inner race to the No. 3 one-way clutch assembly.

      Tech Tips

      Rotate the one-way clutch inner race clockwise to install it.

  12. INSTALL NO. 3 ONE-WAY CLUTCH ASSEMBLY WITH ONE-WAY CLUTCH INNER RACE


    1. B00290B

      Install the No. 3 one-way clutch assembly with one-way clutch inner race to the automatic transmission case sub-assembly.

    2. B0026PKC01
      *1 Snap Ring
      *a 19°
      *b 49°
      B0068HS Front Side

      Using SST, install the snap ring to the automatic transmission case sub-assembly.

      SST
      09350-30020   ( 09350-07060 )

      Note


      • Install the snap ring so that the tapered side is facing out.

      • Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.

  13. INSPECT CLEARANCE OF NO. 4 BRAKE

    Click here

  14. INSTALL NO. 1 BRAKE PISTON


    1. Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.

    2. B0027FN

      With the No. 1 brake piston return spring sub-assembly installed to the No. 1 brake piston, align the 2 claws of the No. 1 brake piston return spring sub-assembly with the 2 claws of the No. 1 brake cylinder, and then install the No. 1 brake piston to the No. 1 brake cylinder.

  15. INSTALL NO. 1 BRAKE CYLINDER WITH NO. 1 BRAKE PISTON


    1. B0026S5

      Install the No. 1 brake cylinder with No. 1 brake piston to the automatic transmission case sub-assembly while making sure that the 2 claws of the No. 1 brake cylinder with No. 1 brake piston are positioned as shown in the illustration.

  16. INSTALL NO. 1 BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    1. B0024CD

      Align the 2 claws of the No. 1 brake piston return spring sub-assembly with the 2 claws of the No. 1 brake cylinder, and then install the No. 1 brake piston return spring sub-assembly to the No. 1 brake piston.

    2. B0028KCC02
      *a Turn

      Place SST on the No. 1 brake piston return spring sub-assembly, and compress the No. 1 brake piston return spring sub-assembly with a press.

      SST
      09380-60011   ( 09381-06010, 09381-06040, 09381-06050, 09381-06070, 09381-06090, 09381-06100, 09381-06110, 09381-06120 )
    3. B0025GFC01
      *a 22.5°
      *b 37.5°

      Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.

      Note


      • Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.

      • Be careful not to damage the automatic transmission case sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

  17. INSTALL NO. 1 BRAKE DISC


    1. B00257EC01
      *1 No. 1 Brake Flange
      *2 No. 1 Brake Disc
      *3 No. 1 Brake Plate

      Install the No. 1 brake flange, 3 No. 1 brake discs and 3 No. 1 brake plates to the automatic transmission case sub-assembly.

      Note

      Make sure that the No. 1 brake discs, No. 1 brake plates and No. 1 brake flange are installed in the correct order.

    2. B0026DHC01
      *a 22.5°
      *b 37.5°

      Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.

      Note


      • Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.

      • Be careful not to damage the automatic transmission case sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

  18. INSPECT CLEARANCE OF NO. 1 BRAKE

    Click here

  19. INSTALL PLANETARY SUN GEAR


    1. B0024Y1

      Install the planetary sun gear to the automatic transmission case sub-assembly.

  20. INSTALL CENTER PLANETARY GEAR ASSEMBLY


    1. B0027Z4C01
      *1 Thrust Bearing Race I

      Coat the thrust bearing race with ATF and install it to the center planetary gear assembly.

      Thrust Bearing Race Diameter
      Item Inside (mm (in.)) Outside (mm (in.))
      Thrust Bearing Race I 53.7 (2.114) 74.0 (2.913)
    2. Install the center planetary gear assembly to the automatic transmission case sub-assembly.

  21. INSTALL CENTER PLANETARY RING GEAR


    1. B0026SKC01
      *1 Center Planetary Ring Gear Flange
      *2 Center Planetary Ring Gear

      Install the center planetary ring gear to the center planetary ring gear flange.

    2. B00276KC01
      *a Protective Tape

      Using a screwdriver, install the snap ring to the center planetary ring gear flange with center planetary ring gear.

      Note

      Be careful not to damage the center planetary ring gear flange with center planetary ring gear.

      Tech Tips

      Tape the screwdriver tip before use.

  22. INSTALL CENTER PLANETARY RING GEAR FLANGE WITH CENTER PLANETARY RING GEAR


    1. B0025EYC01
      *1 Thrust Needle Roller Bearing H
      *2 Thrust Needle Roller Bearing I

      Coat the 2 thrust needle roller bearings with ATF and install them to the center planetary ring gear flange with center planetary ring gear.

      Thrust Needle Roller Bearing Diameter
      Item Inside (mm (in.)) Outside (mm (in.))
      Thrust Needle Roller Bearing H 63.3 (2.492) 78.8 (3.102)
      Thrust Needle Roller Bearing I 55.7 (2.193) 76.4 (3.008)

      Note

      Be sure to install the thrust needle roller bearing in the correct direction.

    2. Install the center planetary ring gear flange with center planetary ring gear to the automatic transmission case sub-assembly.

  23. INSTALL NO. 2 BRAKE DISC


    1. B0028T2C01
      *1 No. 2 Brake Flange
      *2 No. 2 Brake Disc
      *3 No. 2 Brake Plate

      Install the 2 No. 2 brake flanges, 4 No. 2 brake discs and 3 No. 2 brake plates to the automatic transmission case sub-assembly.

      Note


      • Make sure that the No. 2 brake discs, No. 2 brake plates and No. 2 brake flanges are installed in the correct order.

      • Install the thicker No. 2 brake flange first, and then install the thinner one.

  24. INSTALL NO. 2 BRAKE PISTON


    1. Coat 2 new O-rings with ATF and install them to the No. 2 brake piston.

    2. B00250E

      With the No. 2 brake piston return spring sub-assembly installed to the No. 2 brake piston, align the claw of the No. 2 brake piston return spring sub-assembly with the claw of the No. 2 brake cylinder, and then install the No. 2 brake piston to the No. 2 brake cylinder.

      Note

      Be careful not to damage the O-rings.

  25. INSTALL NO. 2 BRAKE CYLINDER WITH NO. 2 BRAKE PISTON


    1. B0026F2

      Install the No. 2 brake piston return spring sub-assembly to the automatic transmission case sub-assembly while making sure that the claw of the No. 2 brake piston return spring sub-assembly is positioned as shown in the illustration.

    2. B002794

      Install the No. 2 brake cylinder with No. 2 brake piston to the automatic transmission case sub-assembly while making sure that the claw of the No. 1 brake cylinder with No. 1 brake piston is positioned as shown in the illustration.

    3. B00252RC02
      *a Turn

      Place SST on the No. 2 brake cylinder, and compress the No. 2 brake piston return spring sub-assembly with a press.

      SST
      09380-60011   ( 09381-06010, 09381-06020, 09381-06040, 09381-06050, 09381-06060, 09381-06090, 09381-06100, 09381-06110, 09381-06120 )
    4. B0025H3C01
      *a 30°

      Using a screwdriver, install the snap ring to the automatic transmission case sub-assembly.

      Note


      • Be sure to install the snap ring so that the ends of the snap ring are within the area shown in the illustration.

      • Be careful not to damage the automatic transmission case sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

  26. INSTALL CLEARANCE OF NO. 2 BRAKE

    Click here

  27. INSTALL FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY


    1. B00288GC01
      *1 Front Planetary Ring Gear
      *2 Snap Ring
      *3 Front Planetary Ring Gear Flange Sub-assembly

      Set the snap ring onto the front planetary ring gear flange sub-assembly. Using needle-nose pliers, insert the snap ring into the front planetary ring gear while squeezing it, and then expand the snap ring to install it.

      Note

      Make sure the snap ring is securely inserted into the groove of the front planetary ring gear.

  28. INSTALL FRONT PLANETARY RING GEAR WITH FRONT PLANETARY RING GEAR FLANGE SUB-ASSEMBLY


    1. B0025S5C01
      *1 Thrust Needle Roller Bearing G
      *2 Thrust Bearing Race H

      Coat the thrust needle roller bearing and thrust bearing race with ATF and install them to the front planetary ring gear with front planetary ring gear flange sub-assembly.

      Thrust Needle Roller Bearing and Thrust Bearing Race Diameter
      Item Inside (mm (in.)) Outside (mm (in.))
      Thrust Needle Roller Bearing G 63.3 (2.492) 78.8 (3.102)
      Thrust Bearing Race H 66.3 (2.610) 78.9 (3.106)

      Note

      Be sure to install the thrust needle roller bearing and thrust bearing race in the correct direction.

    2. Install the front planetary ring gear with front planetary ring gear flange sub-assembly to the automatic transmission case sub-assembly.

  29. INSTALL FRONT PLANETARY GEAR ASSEMBLY


    1. B0026BVC01
      *1 Thrust Bearing Race F
      *2 Thrust Bearing Race G

      Coat the 2 thrust bearing races with ATF and install them to the front planetary gear assembly.

      Thrust Bearing Race Diameter
      Item Inside (mm (in.)) Outside (mm (in.))
      Thrust Bearing Race F 44.0 (1.732) 62.8 (2.472)
      Thrust Bearing Race G 65.8 (2.591) 86.3 (3.398)

      Note

      Be sure to install the thrust bearing race in the correct direction.

    2. Install the front planetary gear assembly to the automatic transmission case sub-assembly.

  30. INSTALL SUN GEAR INPUT DRUM SUB-ASSEMBLY


    1. B0025HNC01
      *1 Thrust Bearing Race E
      *2 Thrust Needle Roller Bearing F

      Coat the thrust needle roller bearing and thrust bearing race with ATF and install them to the sun gear input drum sub-assembly.

      Thrust Needle Roller Bearing and Thrust Bearing Race Diameter
      Item Inside (mm (in.)) Outside (mm (in.))
      Thrust Bearing Race E 40.83 (1.607) 52.8 (2.079)
      Thrust Needle Roller Bearing F 37.1 (1.461) 61.2 (2.409)

      Note

      Be sure to install the thrust needle roller bearing and thrust bearing race in the correct direction.

    2. Install the sun gear input drum sub-assembly to the automatic transmission case sub-assembly.

  31. INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY


    1. B0025P6C01
      *1 Thrust Needle Roller Bearing D
      *2 Thrust Needle Roller Bearing E

      Coat the 2 thrust needle roller bearings with ATF and install them to the forward clutch hub sub-assembly.

      Thrust Needle Roller Bearing Diameter
      Item Inside (mm (in.)) Outside (mm (in.))
      Thrust Needle Roller Bearing D 33.3 (1.311) 56.6 (2.228)
      Thrust Needle Roller Bearing E 39.6 (1.559) 52.8 (2.079)

      Note

      Be sure to install the thrust needle roller bearing in the correct direction.

    2. Install the forward clutch hub sub-assembly to the automatic transmission case sub-assembly.

  32. INSTALL MULTIPLE DISC CLUTCH HUB


    1. B0025K7C01
      *1 Thrust Bearing Race C
      *2 Thrust Bearing Race D

      Coat the 2 thrust bearing races with ATF and install them to the multiple disc clutch hub.

      Thrust Bearing Race Diameter
      Item Inside (mm (in.)) Outside (mm (in.))
      Thrust Bearing Race C 22.6 (0.866) 44.8 (1.764)
      Thrust Bearing Race D 38.4 (1.512) 56.5 (2.224)

      Note

      Be sure to install the thrust bearing race in the correct direction.

    2. Install the multiple disc clutch hub to the automatic transmission case sub-assembly.

  33. INSTALL DIRECT CLUTCH PISTON


    1. Coat 2 new O-rings with ATF, and install them to the direct clutch piston.

    2. B0027B4

      Install the direct clutch piston to the direct clutch drum sub-assembly.

      Note

      Be careful not to damage the O-rings.

  34. INSTALL NO. 2 CLUTCH BALANCER


    1. B0028N8C01
      *1 No. 2 Clutch Balancer
      *2 Direct Clutch Return Spring Sub-assembly

      Install the direct clutch return spring sub-assembly to the direct clutch piston.

    2. Coat a new O-ring with ATF, and install it to the No. 2 clutch balancer.

    3. Install the No. 2 clutch balancer to the direct clutch drum sub-assembly.

      Note

      Be careful not to damage the O-ring.

    4. B00258MN03

      Place SST on the No. 2 clutch balancer, and compress the direct clutch return spring sub-assembly with a press.

      SST
      09380-60011   ( 09381-06030, 09381-06040, 09381-06080, 09381-06100, 09381-06110 )

      Note

      Stop pressing when the spring sheet is lowered to the place 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.

    5. Using SST, install the snap ring.

      SST
      09350-30020   ( 09350-07070 )

      Note

      Do not expand the snap ring excessively.

  35. INSTALL NO. 2 CLUTCH DISC (DIRECT CLUTCH DISC)


    1. B0027UEC01
      *1 Direct Clutch Flange
      *2 No. 2 Clutch Disc
      *3 No. 2 Clutch Plate

      Install the 4 No. 2 clutch plates, 4 No. 2 clutch discs and direct clutch flange to the direct clutch drum sub-assembly.

      Note

      Make sure that the No. 2 clutch discs, No. 2 clutch plates and direct clutch flange are installed in the correct order.

    2. B0025ALC01
      *a Protective Tape

      Using a screwdriver, install the snap ring to the direct clutch drum sub-assembly.

      Note

      Be careful not to damage the direct clutch drum sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

  36. INSPECT CLEARANCE OF NO. 2 CLUTCH (DIRECT CLUTCH)

    Click here

  37. INSTALL FORWARD CLUTCH PISTON


    1. Coat a new O-ring with ATF, and install it to the input shaft sub-assembly.

    2. Coat a new O-ring with ATF, and install it to the forward clutch piston.

    3. B002733

      Install the forward clutch piston to the input shaft sub-assembly.

      Note

      Be careful not to damage the O-rings.

  38. INSTALL NO. 1 CLUTCH BALANCER


    1. Coat a new O-ring with ATF, and install it to the No. 1 clutch balancer.

    2. B00267RC01
      *1 No. 1 Clutch Balancer
      *2 Forward Clutch Return Spring Sub-assembly

      Install the forward clutch return spring sub-assembly and No. 1 clutch balancer to the input shaft sub-assembly.

      Note

      Be careful not to damage the O-ring.

    3. B0024Z0N01

      Place SST on the No. 1 clutch balancer, and compress the forward clutch return spring sub-assembly with a press.

      SST
      09387-00110

      Note

      Stop pressing when the spring sheet is lowered to the place 1 to 2 mm (0.0394 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.

    4. Using SST, install the snap ring.

      SST
      09350-30020   ( 09350-07070 )

      Note

      Do not expand the snap ring excessively.

  39. INSTALL NO. 1 CLUTCH DISC (FORWARD CLUTCH DISC)


    1. B0025LPC02
      *1 Forward Clutch Flange
      *2 No. 1 Clutch Disc
      *3 No. 1 Clutch Plate

      Install the 5 No. 1 clutch plates, 5 No. 1 clutch discs and forward clutch flange to the input shaft sub-assembly.

      Note

      Make sure that the No. 1 clutch discs, No. 1 clutch plates and forward clutch flange are installed in the correct order.

    2. B0026V9C01
      *a Protective Tape

      Using a screwdriver, install the snap ring.

      Note

      Be careful not to damage the input shaft sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

  40. INSPECT CLEARANCE OF NO. 1 CLUTCH (FORWARD CLUTCH)

    Click here

  41. INSTALL CLUTCH DRUM OIL SEAL RING


    1. B0027AZ

      Coat 3 new clutch drum oil seal rings with ATF and install them to the input shaft sub-assembly.

      Note

      Do not expand the clutch drum oil seal ring ends excessively.

      Tech Tips

      After installing the clutch drum oil seal rings, check that they rotate smoothly.

  42. INSTALL DIRECT CLUTCH DRUM SUB-ASSEMBLY


    1. B00266TC01
      *1 Direct Clutch Drum Sub-assembly
      *2 Input Shaft Sub-assembly

      Install the direct clutch drum sub-assembly to the input shaft sub-assembly.

  43. INSTALL CLUTCH DRUM AND INPUT SHAFT ASSEMBLY


    1. B0026ZYC01
      *1 Thrust Needle Roller Bearing A
      *2 Thrust Needle Roller Bearing B
      *3 Thrust Needle Roller Bearing C

      Coat the 3 thrust needle roller bearings with ATF and install them to the clutch drum and input shaft assembly.

      Thrust Needle Roller Bearing Diameter
      Item Inside (mm (in.)) Outside (mm (in.))
      Thrust Needle Roller Bearing A 71.9 (2.831) 85.6 (3.370)
      Thrust Needle Roller Bearing B 34.6 (1.362) 52.0 (2.047)
      Thrust Needle Roller Bearing C 21.3 (0.839) 41.1 (1.618)

      Note

      Be sure to install the thrust needle roller bearing in the correct direction.

    2. Install the clutch drum and input shaft assembly to the automatic transmission case sub-assembly.

  44. INSTALL OIL PUMP ASSEMBLY


    1. B0024B8C01
      *1 Thrust Bearing Race B
      *2 Thrust Bearing Race A
      *3 Oil Pump O-ring

      Coat the 2 thrust bearing races with ATF and install them to the oil pump assembly.

      Race Diameter
      Item Inside (mm (in.)) Outside (mm (in.))
      Thrust Bearing Race B 40.0 (1.575) 52.8 (2.079)
      Thrust Bearing Race A 74.2 (2.921) 87.74 (3.454)

      Note

      Be sure to install the thrust bearing race in the correct direction.

    2. Coat a new oil pump O-ring with ATF, and install it to the oil pump assembly.

    3. Set the oil pump assembly on the input shaft, and align the bolt holes of the oil pump assembly with the automatic transmission case sub-assembly.

      Note

      Be careful not to damage the oil pump O-ring.

    4. Temporarily install the oil pump assembly to the automatic transmission case sub-assembly.

    5. B0024H4

      Install the oil pump assembly with the 10 bolts.

      Torque:
      21.1 N*m  { 215 kgf*cm, 16 ft.*lbf }
  45. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL


    1. B00255HN02

      Using SST and a hammer, drive in 2 new manual valve lever shaft oil seals to the automatic transmission case sub-assembly.

      SST
      09350-30020   ( 09350-07110 )
      Standard depth
      -0.5 to 0.5 mm (-0.0196 to 0.0196 in.)
    2. Coat the lip of the manual valve lever shaft oil seal with MP grease.

  46. INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY


    1. B0024JYC01
      *1 Manual Valve Lever Sub-assembly
      *2 Spacer

      Install a new spacer to the manual valve lever sub-assembly.

    2. Install the manual valve lever shaft to the automatic transmission case sub-assembly through the manual valve lever sub-assembly.

    3. B0028AN

      Using a hammer, drive in a new spring pin.

    4. Turn the spacer and manual valve lever shaft to align the smaller hole on the spacer with the indent on the manual valve lever sub-assembly.

    5. B0024KH

      Using a 3 mm pin punch and a hammer, stake the spacer.

    6. Check that the spacer does not turn.

    7. Make sure that the shaft rotates smoothly.

  47. INSTALL PARKING LOCK PAWL SHAFT


    1. Install the E-ring to the parking lock pawl shaft.

    2. B0026P1C02
      *1 Parking Lock Pawl
      *2 E-ring
      *3 Parking Lock Pawl Shaft
      *4 Spring

      Install the parking lock pawl, parking lock pawl shaft and spring to the automatic transmission case sub-assembly.

  48. INSTALL PARKING LOCK ROD SUB-ASSEMBLY


    1. B0024QY

      Install the parking lock rod sub-assembly to the manual valve lever sub-assembly.

  49. INSTALL PARKING LOCK PAWL BRACKET


    1. B0026TO

      Install the parking lock pawl bracket to the automatic transmission case sub-assembly with the 3 bolts.

      Torque:
      18 N*m  { 184 kgf*cm, 13 ft.*lbf }
    2. Move the manual valve lever sub-assembly to P, and check the output shaft is locked by the parking lock pawl.

  50. INSTALL BRAKE DRUM GASKET


    1. B0026WJ

      Coat 2 new brake drum gaskets with ATF and install them to the automatic transmission case sub-assembly.

  51. INSTALL TRANSMISSION CASE GASKET


    1. B0024IY

      Coat 2 new transmission case gaskets with ATF and install them to the automatic transmission case sub-assembly.

  52. INSTALL TRANSMISSION VALVE BODY ASSEMBLY


    1. B0028PBC02
      *1 Manual Valve Lever Sub-assembly
      *2 Manual Valve

      Insert the manual valve lever sub-assembly into the groove on the end of the manual valve and install the transmission valve body assembly to the automatic transmission case sub-assembly with the 12 bolts.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

      Tech Tips


      • Bolt A: 25 mm (0.984 in.)

      • Bolt B: 36 mm (1.42 in.)

      • Bolt C: 50 mm (1.97 in.)

    2. B0025GG

      Install the detent spring and detent spring cover to the transmission valve body assembly with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
  53. INSTALL VALVE BODY OIL STRAINER ASSEMBLY


    1. Coat a new O-ring with ATF, and install it to the valve body oil strainer assembly.

    2. B0028GG

      Install the valve body oil strainer assembly to the transmission valve body assembly with the 3 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
  54. INSTALL TRANSMISSION WIRE


    1. B0026RS

      Coat 2 new O-rings with ATF, and install them to the 2 temperature sensors.

    2. B0024P4

      Coat a new O-ring with ATF, and install it to the transmission wire.

    3. B0025N6

      Install the transmission wire to the automatic transmission case sub-assembly with the bolt.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }
    4. B00285DC04
      *1 Temperature Sensor Clamp
      *2 Temperature Sensor

      Connect the 7 solenoid valve connectors.

    5. Install the 2 temperature sensors and 2 temperature sensor clamps to the transmission valve body assembly with the bolt.

      Torque:
      for Bolt A
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
      for Bolt B
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }
  55. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY


    1. B0028PQ

      Install the 4 transmission oil cleaner magnets to the automatic transmission oil pan sub-assembly as shown in the illustration.

    2. Install a new automatic transmission oil pan gasket to the automatic transmission oil pan sub-assembly.

    3. B0028YN

      Install the automatic transmission oil pan sub-assembly with automatic transmission oil pan gasket to the automatic transmission case sub-assembly with the 10 bolts.

      Torque:
      7.4 N*m  { 75 kgf*cm, 65 in.*lbf }

      Note


      • Make sure that automatic transmission oil pan gasket seal surface and automatic transmission oil pan sub-assembly contact surface are free of oil and foreign matter.

      • Install the automatic transmission oil pan gasket so that there is no slack in the automatic transmission oil pan gasket, and the entire seal surface is level.

      • Make sure that the 8 protrusions are properly engaged to the automatic transmission oil pan sub-assembly.

      • When installing the automatic transmission oil pan sub-assembly, make sure that the automatic transmission oil pan gasket is not pinched between the sleeve and the seal surface of the automatic transmission case sub-assembly.

      B0025NFC06
      *1 Sleeve
      *2 Automatic Transmission Case Sub-assembly
      *a Correct
      *b Incorrect
      *c Protrusion
    4. Install the drain plug and a new gasket to the automatic transmission oil pan sub-assembly.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }
    5. Using a 5 mm hexagon socket wrench, install a new gasket and overflow plug to the automatic transmission oil pan sub-assembly.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }
  56. INSTALL AUTOMATIC TRANSMISSION HOUSING


    1. Clean and degrease the bolts and bolt holes with non-residue solvent.

    2. B0026C3

      Install the automatic transmission housing to the automatic transmission case sub-assembly with the 8 bolts.

      Torque:
      33.9 N*m  { 346 kgf*cm, 25 ft.*lbf }
    3. Apply adhesive to 2 or 3 threads on the end of the 4 bolts.

      Adhesive
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
    4. B0025ARN02

      Install 4 bolts to the automatic transmission housing.

      Torque:
      for Bolt A (M10 bolt)
      33.9 N*m  { 346 kgf*cm, 25 ft.*lbf }
      for Bolt B (M12 bolt)
      56.8 N*m  { 579 kgf*cm, 42 ft.*lbf }
  57. INSTALL AUTOMATIC TRANSMISSION EXTENSION HOUSING OIL SEAL


    1. B0025U5N01

      Using SST and a hammer, drive in a new automatic transmission extension housing oil seal to the extension housing sub-assembly.

      SST
      09309-37010
      Standard depth
      5.4 to 5.8 mm (0.213 to 0.228 in.)
    2. Coat the lip of the automatic transmission extension housing oil seal with MP grease.

  58. INSTALL EXTENSION HOUSING DUST DEFLECTOR


    1. B0026T0N01

      Using SST and a press, install a new extension housing dust deflector to the extension housing sub-assembly.

      SST
      09550-55011   ( 09550-05081 )
  59. INSTALL EXTENSION HOUSING SUB-ASSEMBLY


    1. Clean and degrease the threads of the 8 bolts, bolt holes and the contact surfaces of the automatic transmission case sub-assembly and extension housing sub-assembly with non-residue solvent.

    2. B0025YMC01
      *a Seal Packing

      Apply seal packing to the extension housing sub-assembly as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

      Note


      • Apply seal packing in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface.

      • After applying seal packing, install the extension housing sub-assembly to the automatic transmission case sub-assembly within 3 minutes and tighten the bolts within 10 minutes.

    3. Apply adhesive to 2 or 3 threads on the end of the 8 bolts.

      Adhesive
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent
    4. B0026FNN01

      Install the extension housing sub-assembly to the automatic transmission case sub-assembly with the 8 bolts.

      Torque:
      33.9 N*m  { 346 kgf*cm, 25 ft.*lbf }
      Bolt Length
      Bolt A 40 mm (1.57 in.)
      Bolt B 45 mm (1.77 in.)
  60. INSTALL OIL COOLER TUBE UNION


    1. Coat 2 new O-rings with ATF and install them to the 2 oil cooler tube unions.

    2. B002728C02
      *a Torque Wrench Fulcrum Length
      *b 18° to 22°
      *c -2° to 2°

      Using SST, install the 2 oil cooler tube unions to the automatic transmission case sub-assembly.

      SST
      09268-78010
      Torque:
      Specified tightening torque
      29.4 N*m  { 300 kgf*cm, 22 ft.*lbf }

      Tech Tips


      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Click here

      • When using SST (fulcrum length of 34.5 mm (1.3583 in.)) + torque wrench (fulcrum length of 180 mm (7.0866 in.)): 24.7 N*m (252 kgf*cm, 18 ft.*lbf)

  61. INSTALL AUTOMATIC TRANSMISSION CASE PLUG


    1. Coat 6 new O-rings with ATF, and install them to the 6 automatic transmission case plugs.

    2. B0024DW

      Install the 6 automatic transmission case plugs to the automatic transmission case sub-assembly.

      Torque:
      7.4 N*m  { 75 kgf*cm, 65 in.*lbf }
    3. Coat a new O-ring with ATF, and install it to the automatic transmission case plug.

    4. B00253G

      Using a T55 "TORX" socket wrench, install the automatic transmission case plug to the automatic transmission case sub-assembly.

      Torque:
      39.2 N*m  { 400 kgf*cm, 29 ft.*lbf }
  62. INSTALL REFILL PLUG


    1. Coat a new O-ring with ATF, and install it to the refill plug.

    2. B0027N0

      Install the refill plug to the automatic transmission case sub-assembly.

      Torque:
      39.2 N*m  { 400 kgf*cm, 29 ft.*lbf }
  63. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

    Tech Tips

    Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch assembly as the detent spring may become detached from the manual valve lever shaft.


    1. Clean the bolt and bolt hole.

    2. Apply adhesive to 2 or 3 threads on the end of the bolt.

      Adhesive
      Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

      Note

      Install the bolt within 3 minutes of applying adhesive.

    3. B00271K

      Temporarily install the park/neutral position switch assembly to the automatic transmission case sub-assembly with the bolt.

    4. Install the lock washer and nut to the park/neutral position switch assembly.

      Torque:
      6.9 N*m  { 70 kgf*cm, 61 in.*lbf }
    5. Temporarily install the transmission control shaft lever LH to the manual valve lever shaft with the spring washer and nut.

    6. B0025ESN01

      Turn the transmission control shaft lever LH clockwise until it stops, and then return the transmission control shaft lever LH counterclockwise 2 notches to N.

    7. B0024DFC14
      *a Neutral Basic Line
      *b Groove

      Align the neutral basic line with the groove as shown in the illustration, and tighten the bolt.

      Torque:
      12.8 N*m  { 131 kgf*cm, 9 ft.*lbf }
    8. Using a screwdriver, bend the tabs of the lock washer.

      Note


      • Be careful not to damage the park/neutral position switch assembly.

      • Bend at least 2 of the lock washer tabs.

      Tech Tips

      Tape the screwdriver tip before use.

  64. INSTALL TRANSMISSION CONTROL SHAFT LEVER LH


    1. B0027N3

      Install the transmission control shaft lever LH to the manual valve lever shaft with the spring washer and nut.

      Torque:
      15.7 N*m  { 160 kgf*cm, 12 ft.*lbf }
  65. INSTALL TRANSMISSION REVOLUTION SENSOR


    1. Coat a new O-ring with ATF, and install it to the transmission revolution sensor (NT).

    2. B0024J0

      Install the transmission revolution sensor (NT) to the automatic transmission case sub-assembly with the bolt.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }
    3. B0026SP

      Coat a new O-ring with ATF, and install it to the transmission revolution sensor (SP2).

    4. Install the transmission revolution sensor (SP2) to the automatic transmission case sub-assembly with the bolt.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }
  66. INSTALL BREATHER PLUG HOSE


    1. B0024W2C01
      *1 Breather Plug Sub-assembly
      *2 Breather Plug Hose
      *3 Breather Plug
      *4 O-ring

      Install the breather plug sub-assembly and breather plug to the breather plug hose.

    2. Coat a new O-ring with ATF, and install it to the breather plug.

    3. B0025JB

      Install the breather plug hose to the automatic transmission case sub-assembly.

      Note

      Be careful not to damage the O-rings.