ECD SYSTEM, Diagnostic DTC:P1477,P2008,P2009 and P2010

DTC Code DTC Name
P1477 Swirl Valve Circuit Error
P2008 Open Load Error
P2009 Intake Manifold Runner Control Circuit Low Bank 1
P2010 Intake Manifold Runner Control Circuit High Bank 1

DESCRIPTION

Refer to DTC P2016.

Click here

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

P1477

Swirl Valve Circuit Error

Either condition is met (3 trip detection logic):

  • An overload due to a short circuit in the battery is detected in the swirl control valve circuit for 0.2 seconds.

  • Swirl control valve circuit over temperature for 0.2 seconds.

  • Swirl control valve circuit overcurrent for 0.2 seconds.

  • Open or short in swirl control valve circuit

  • Swirl control valve

  • ECM

Does not come on

DTC stored

P2008

Open Load Error

Open in swirl control valve actuator circuit for 0.2 seconds.

(3 trip detection logic)

  • Open or short in swirl control valve circuit

  • Swirl control valve

  • ECM

Does not come on

DTC stored

P2009

Intake Manifold Runner Control Circuit Low Bank 1

Ground short in swirl control valve actuator circuit for 0.2 seconds.

(3 trip detection logic)

  • Open or short in swirl control valve circuit

  • Swirl control valve

  • ECM

Does not come on

DTC stored

P2010

Intake Manifold Runner Control Circuit High Bank 1

Battery short in swirl control valve actuator circuit for 0.2 seconds.

(3 trip detection logic)

  • Open or short in swirl control valve circuit

  • Swirl control valve

  • ECM

Does not come on

DTC stored
Table 1. Related Data List

DTC No.

Data List

P1477

P2008

P2009

P2010

Swirl Valve Actuator Position

WIRING DIAGRAM

Refer to DTC P2016.

Click here

CAUTION / NOTICE / HINT

Note:

  • When replacing the ECM, the ECM needs registration and initialization.

    Click here

  • After replacing the swirl control valve, the ECM needs initialization.

    Click here

Tip:

  • When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initialization/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.

  • Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

PROCEDURE

  1. PERFORM ACTIVE TEST USING GTS (ACTUATOR TEST OF SWIRL FLAP)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Start the engine.

    4. Enter the following menus: Powertrain / Engine and ECT / Active Test / Actuator Test of Swirl Flap / Data List / Swirl Valve Actuator Position.

      Powertrain > Engine and ECT > Active Test

      Active Test Display

      Actuator Test of Swirl Flap

      Data List Display

      Swirl Valve Actuator Position

      OK

      The value of "Swirl Valve Actuator Position" changes according to the amount "Actuator Test of Swirl Flap" is operated, and the swirl flap operates smoothly.

    Result

    Proceed to

    OK

    NG
    OK

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

    NG

  2. CHECK HARNESS AND CONNECTOR (SWIRL CONTROL VALVE - ECM)

    1. Disconnect the swirl control valve connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      B129-3 (SCV+) - B112-49 (IA1+)

      Always

      Below 1 Ω

      B129-4 (SCV-) - B112-19 (IA1-)

      Always

      Below 1 Ω

      B129-3 (SCV+) or B112-49 (IA1+) - Body ground

      Always

      10 kΩ or higher

      B129-4 (SCV-) or B112-19 (IA1-) - Body ground

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTORClick here

    OK

  3. REPLACE SWIRL CONTROL VALVE

    1. Replace the swirl control valve.

      Click here

    2. Perform the swirl valve learning value reset.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  4. CHECK WHETHER DTC OUTPUT RECURS (DTC P1477, P2008, P2009 AND/OR P2010)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

      Powertrain > Engine and ECT > Trouble Codes

    8. Read the DTCs.

      Result

      Result

      Result

      Proceed to

      No DTC output

      No DTC output

      A

      DTC P1477, P2008, P2009 and/or P2010

      DTC P1477, P2008, P2009 and/or P2010

      B
    A

    END

    B

  5. REPLACE ECM

    1. Replace the ECM.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIREDClick here

  6. REPAIR OR REPLACE HARNESS OR CONNECTOR

    1. Repair or replace the harness or connector.

    Result

    Proceed to

    NEXT
    NEXT

  7. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Powertrain > Engine and ECT > Clear DTCs

    4. Turn the ignition switch off and wait for 60 seconds or more [A].

    5. Perform road test [B].

    6. Repeat [A] and [B] for the number of trips detected.

    7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

      Powertrain > Engine and ECT > Trouble Codes

    8. Confirm that the DTC is not output again.

    Result

    Proceed to

    NEXT
    NEXT

    END