EXHAUST MANIFOLD W/ TURBOCHARGER REMOVAL

PROCEDURE

  1. PRECAUTION

    Note:

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  3. DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL

  4. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

    (Click here)

  5. REMOVE NO. 1 ENGINE UNDER COVER

    Click here

  6. DRAIN ENGINE COOLANT

    Click here

  7. REMOVE RADIATOR SUPPORT OPENING COVER

    Click here

  8. REMOVE BATTERY CLAMP SUB-ASSEMBLY

    1. A313616

      Remove the bolt and loosen the nut.

    2. Detach the hook of the battery clamp sub-assembly from the battery carrier, and then remove the battery clamp sub-assembly.

  9. REMOVE BATTERY INSULATOR

  10. REMOVE BATTERY

  11. REMOVE BATTERY TRAY

  12. REMOVE BATTERY CARRIER

    1. A313617

      Detach the 2 clamps and disconnect the engine wire.

    2. Remove the 4 bolts and battery carrier.

  13. REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE ASSEMBLY

    1. A337409E02

      Detach the clamp and disconnect the mass air flow meter sub-assembly connector.

      Table 1. Text in Illustration

      *1

      Retainer

    2. Detach the clamp and disconnect the vacuum hose from the air cleaner hose assembly.

    3. Detach the clamp and disconnect the No. 1 fuel hose from the air cleaner hose assembly.

    4. Detach the clamp and disconnect the No. 2 fuel hose from the air cleaner hose assembly.

    5. Disconnect the ventilation hose from the cylinder head cover sub-assembly.

    6. Release the retainer and disconnect the air cleaner hose assembly from the turbocharger sub-assembly as shown in the illustration.

    7. Detach the 2 clamps and remove the air cleaner cap sub-assembly with air cleaner hose assembly.

  14. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

  15. REMOVE AIR CLEANER CASE SUB-ASSEMBLY

    1. A313618

      Remove the 3 bolts and air cleaner case sub-assembly.

  16. DISCONNECT COMPRESSOR OUTLET ELBOW

    1. A337410E01

      Release the retainer and disconnect the compressor outlet elbow from the turbocharger sub-assembly as shown in the illustration.

      Table 2. Text in Illustration

      *1

      Retainer

  17. REMOVE TURBO OIL OUTLET PIPE

    1. A337411

      Remove the 3 bolts, turbo oil outlet pipe and gasket.

    2. Remove the O-ring from the turbo oil outlet pipe.

  18. DISCONNECT NO. 1 TURBO OIL PIPE

    1. A337412

      Remove the union bolt and 2 gaskets and disconnect the No. 1 turbo oil pipe.

  19. REMOVE NO. 1 EXHAUST MANIFOLD PIPE

    1. Disconnect the exhaust manifold pressure sensor connector.

    2. A337413

      Remove the union bolt and 2 gaskets.

    3. Remove the bolt and No. 1 exhaust manifold pipe.

  20. REMOVE TURBOCHARGER SUB-ASSEMBLY

    1. A337414

      Disconnect the connector from the turbocharger sub-assembly.

    2. Remove the 4 bolts, turbocharger sub-assembly and gasket.

  21. DISCONNECT ENGINE WIRE

    1. A337415

      Detach the 2 clamps from the No. 1 air tube assembly.

    2. Remove the 2 bolts and disconnect the engine wire from the No. 1 air tube assembly.

  22. REMOVE NO. 4 WATER BY-PASS HOSE

    1. A337423E02

      Release the retainer and disconnect the No. 4 water by-pass hose from the EGR cooler assembly as shown in the illustration.

      Table 3. Text in Illustration

      *1

      Retainer

    2. Slide the clamp and remove the No. 4 water by-pass hose from the No. 2 radiator pipe.

  23. DISCONNECT NO. 1 AIR TUBE ASSEMBLY

    1. A337416

      Slide the clamp and disconnect the water by-pass hose assembly from the No. 2 radiator pipe.

    2. Slide the clamp and disconnect the radiator hose sub-assembly from the No. 1 radiator pipe.

    3. Detach the clamp and disconnect the water hose sub-assembly from the compressor outlet elbow.

    4. Slide the clamp and disconnect the water hose sub-assembly from the No. 1 radiator pipe.

    5. Slide the clamp and disconnect the outlet heater water hose from the No. 2 radiator pipe.

    6. Remove the 2 bolts and disconnect the No. 1 air tube assembly from the manual transaxle assembly.

  24. DISCONNECT FUEL FEED PIPE SUB-ASSEMBLY

    Click here

  25. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

    Click here

  26. REMOVE EGR COOLER ASSEMBLY WITH EGR VALVE ASSEMBLY

    Click here

  27. REMOVE EXHAUST MANIFOLD

    1. A337417

      Remove the 8 nuts and exhaust manifold.

    2. Remove the 2 gaskets from the cylinder head sub-assembly.