SFI SYSTEM, Diagnostic DTC:P0107 and P0108

DTC Code DTC Name
P0107 Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Low
P0108 Manifold Absolute Pressure / Barometric Pressure Sensor Circuit High

DESCRIPTION

Refer to DTC P0106.

Click here

DTC No.

Detection Item

DTC Detection Condition

Trouble Area

MIL

Memory

P0107

Manifold Absolute Pressure / Barometric Pressure Sensor Circuit Low

Short to ground in air pressure sensor assembly circuit.

  • Air pressure sensor assembly

  • Wire harness or connector

  • ECM

Comes on

DTC stored

P0108

Manifold Absolute Pressure / Barometric Pressure Sensor Circuit High

Short to +B in air pressure sensor assembly circuit.

  • Air pressure sensor assembly

  • Wire harness or connector

  • ECM

Comes on

DTC stored

MONITOR DESCRIPTION

These DTCs are stored when a malfunction is detected in the air pressure sensor assembly circuit. If there is an open or short in the air pressure sensor assembly circuit when the ignition switch is turned to ON, the ECM will illuminate the MIL and store a DTC.

WIRING DIAGRAM

A330210E01

PROCEDURE

  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0107 AND/OR P0108)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Trouble Codes.

    5. Check for DTCs.

      Powertrain > Engine > Trouble Codes

      Result

      Result

      Proceed to

      DTC P0106, P0107 and/or P0108 is output

      A

      DTC P0107 and/or P0108 and other DTCs are output

      B
      Tip:

      If DTC P0107 and/or P0108 and P0562, P0563 or P0658 are output simultaneously, troubleshoot for DTC P0562, P0563 or P0658 first.

    B

    GO TO DTC CHART

    Click here

    A

  2. READ VALUE USING GTS (MEASURING OF THE INLET PRESSURE)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine / Data List / Measuring of the Inlet Pressure.

      Powertrain > Engine > Data List

      Tester Display

      Measuring of the Inlet Pressure

    5. Read the value while ignition switch is ON and engine running.

      Standard

      Data List

      Condition

      Value

      Measuring of the Inlet Pressure

      Ignition switch ON

      Same value as the actual atmospheric pressure

      Idling with warm engine

      20 to 40 kPa
    Tip:

    • Standard atmospheric pressure is 101 kPa(abs) [758 mmHg(abs)]. For every 100 m (328 ft.) increase in altitude, atmospheric pressure drops by approximately 1 kPa (7.5 mmHg). The pressure also varies due to the weather (high atmospheric pressure, low atmospheric pressure).

    • Check "Atmospheric Pressure" in the Data List.

    Result

    Proceed to

    OK

    NG
    OK

    CHECK FOR INTERMITTENT PROBLEMS

    Click here

    NG

  3. CHECK HARNESS AND CONNECTOR (AIR PRESSURE SENSOR ASSEMBLY - ECM)

    1. Disconnect the air pressure sensor assembly connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection

      Condition

      Specified Condition

      B36-1 (PIM) - B55-13 (PIM)

      Always

      Below 1 Ω

      B36-2 (VC) - B55-25 (VCPM)

      Always

      Below 1 Ω

      B36-4 (E2) - B55-24 (E2)

      Always

      Below 1 Ω

      B36-1 (PIM) or B55-13 (PIM) - Body ground and other terminals

      Always

      10 kΩ or higher

      B36-2 (VC) or B55-25 (VCPM) - Body ground and other terminals

      Always

      10 kΩ or higher

      B36-4 (E2) or B55-24 (E2) - Body ground and other terminals

      Always

      10 kΩ or higher

    Result

    Proceed to

    OK

    NG
    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. REPLACE AIR PRESSURE SENSOR ASSEMBLY

    1. Replace the air pressure sensor assembly.

      Click here

    Result

    Proceed to

    NEXT
    NEXT

  5. CHECK WHETHER DTC OUTPUT RECURS (DTC P0107 OR P0108)

    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.

      Powertrain > Engine > Clear DTCs

    5. Turn the ignition switch off and wait for a few minutes.

    6. Perform the drive test.

    7. Turn the GTS on.

    8. Enter the following menus: Powertrain / Engine / Trouble Codes.

    9. Check for DTCs.

      Powertrain > Engine > Trouble Codes

    Result

    Result

    Proceed to

    DTC P0107 or P0108 is output

    A

    DTCs are not output

    B
    A

    REPLACE ECM

    Click here

    B

    END