SFI SYSTEM INITIALIZATION

Inspection After Repair

Perform Learning Value Reset and Idle Learning after replacing or servicing parts related to engine operation. Details on procedures required are indicated by an asterisk and a number, and are explained in detail following the table.

Part Replaced	Engine Operation	Learning Value Reset*1	Idle Learning*2
Throttle body with motor assembly3 Cleaning the deposits from the throttle body with motor assembly3	-	○	○
Engine assembly	-	○	○
Cylinder head sub-assembly Camshaft (for intake or exhaust camshaft) Camshaft timing gear assembly Camshaft timing exhaust gear assembly Piston or piston ring Mass air flow meter Fuel injector assembly Fuel pump (for low pressure side) Fuel pump assembly (for high pressure side) Air fuel ratio sensor (sensor 1) Air fuel ratio sensor (sensor 2) (w/ Differential Pressure Sensor) Engine coolant temperature sensor Spark plug No. 1 Ignition coil Air leaks from intake system Gas leaks from exhaust system	Confirm the following and perform Learning Value Reset and Idle Learning when one or more of the following conditions is met: A DTC was output before component replacement. An air fuel ratio learned value (A/F Learn Value Idle Bank 1, A/F Learn Value Low Bank 1, A/F Learn Value Mid No. 1 Bank 1, A/F Learn Value Mid No. 2 Bank 1 or A/F Learn Value High Bank 1) displayed in the Data List was higher than +/- 20% before component replacement. Starting failure or rough idle occurs, or the engine stalls after component replacement.	○	○
	The none of the conditions in the list above are met.	-	-
Front exhaust pipe assembly (w/ Differential Pressure Sensor)*4	-	-	-
Knock sensor*5	-	-	-

○: Necessary.
-: Unnecessary.

Note

Engine learned values cannot be reset by disconnecting the cable from the negative (-) battery terminal or removing the EFI-MAIN NO. 1 and ETCS fuses.

*1: Learning Value Reset

Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Learning Value Reset.
Confirm the following conditions as instructed on the screen.

- Ignition switch ON
- Engine stopped
- Battery voltage is higher than 9 V

After confirming, select "Next" and initialize the learned value.

Tech Tips

If a message indicating learned value initialization failure is displayed on the screen, confirm the execution conditions, and perform Learning Value Reset again.

After the completion of learned value initialization, confirm the air fuel ratio learned values (A/F Learn Value Idle Bank 1, A/F Learn Value Low Bank 1, A/F Learn Value Mid No. 1 Bank 1, A/F Learn Value Mid No. 2 Bank 1 and A/F Learn Value High Bank 1) in the Data List.

Result
If 0 is displayed for all of the air fuel ratio learned values, initialization has completed correctly.
If a value other than 0 is displayed for one of the air fuel ratio learned values, perform initialization again. After initialization, confirm the air fuel ratio learned values. If a value other than 0 is displayed, replace the ECM.

*2: Idle Learning

Turn the ignition switch off and wait for at least 30 seconds.
Start the engine and warm it up with the air conditioning and all accessories off, until the engine coolant temperature is 80°C (176°F) or higher.

Tech Tips

Learning starts when the engine coolant temperature is 80°C (176°F) or higher.
After the engine is warmed up, allow it to idle for 5 minutes with the air conditioning and all accessories off.

Confirm that the idle speed is within the specified range.

Standard (for CVT)

Engine Idle Speed
680 to 780 rpm

Standard (for Manual Transaxle):
Engine Idle Speed
600 to 700 rpm

Tech Tips

Be sure to perform this step with all accessories off.
Make sure that the shift lever is in P or N (neutral).

*3: Perform Learning Value Reset and Idle Learning after replacing the throttle body with motor assembly or cleaning deposits from the throttle body with motor assembly.

After that, check the idle speed. If the idle speed is out of the specified range, perform the following procedure.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.

Tech Tips

History information for driving and stopping is necessary to update Idle Learning.


*1	10 km/h (6 mph)
*2	Idling
*3	Ignition Switch ON
*4	20 seconds or more

Warm up the engine (engine coolant temperature of 80°C (176°F) or higher) with the A/C switch and all accessories off [A].
Drive the vehicle at a speed of 10 km/h (6 mph) or more [B].
Idle the engine for 20 seconds or more [C].

Repeat steps [B] and [C], and check that the idle speed is within the specified range [D].

Standard (for CVT)

Engine Idle Speed
680 to 780 rpm

Standard (for Manual Transaxle):
Engine Idle Speed
600 to 700 rpm

Tech Tips

Be sure to perform this step with the A/C switch and all accessories off.
Make sure that the shift lever is in P or N (neutral).
If the idle speed is still out of the specified range, repeat steps [B] and [C] until the idle speed is within the specified range [E].

*4: Clear GPF Deposition Values

Tech Tips

This function initializes the volumes of accumulated ash (metal oxide) and PM (Particulate Matter) recorded by the ECM when replacing the GPF (Gasoline Particulate Filter).

Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / GPF Deposition Values Clear.
According to the display on the GTS, initialize the volumes of accumulated ash and PM.

*5: Drive the vehicle for a short while after replacing the Knock sensor and check if knocking occurs. If knocking occurs, drive the vehicle until knocking stops.

CLEAR HEAVY KNOCK HISTORY

Tech Tips

This function clears the stored history data when the piston rings are replaced.
1. Connect the GTS to the DLC3.
2. Turn the ignition switch to ON.
3. Turn the GTS on.
4. Enter the following menus: Powertrain / Engine / Utility / Heavy Knock History / Clear History.
  
  Powertrain > Engine > Utility
  
  Tester Display
  
  Heavy Knock History
5. Clear the history data according to the instructions on the GTS screen.