FRONT DOOR LOCK REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front door lock with motor assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control)

Click here

Simple intelligent parking assist system*1
Toyota parking assist-sensor system (w/ Simple Intelligent Parking Assist System)*1
Pre-collision system
Initialize back door lock Power door lock control system

Click here

Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)*2 Stop and start system

Click here


  • Front door glass sub-assembly

  • Front door glass run

 Initialize Power Window Control System

  • Auto up and down function

  • Jam protection function

  • Catch protection function

  • Remote control function

  • Key-linked function

  • Wireless transmitter-linked function

  • Key-off operation function

  • Window open warning function

Click here

*1: When performing learning using the GTS.

Click here

*2: w/ Stop and start system

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG

    Click here

  4. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)

    Click here

  5. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)

    Click here

  6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

    Click here

  7. REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP

    Click here

  8. REMOVE FRONT DOOR BELT SEAL

    Click here

  9. REMOVE FRONT DOOR SERVICE HOLE COVER

    Click here

  10. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

    Click here

  11. REMOVE DOOR FRAME UPPER GARNISH

    Click here

  12. REMOVE FRONT DOOR GLASS RUN

    Click here

  13. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY

    Click here

  14. REMOVE FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)

    Click here

  15. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY


    1. B008K8UC01
      *1 Front Door Lock Open Rod
      B008LJK Remove in this Direction

      Disconnect the connector.

    2. Using a T30 "TORX" socket wrench, remove the 3 screws.

    3. Disconnect the front door lock open rod as shown in the illustration.

    4. Remove the front door lock with motor assembly.

    5. When reusing the front door lock with motor assembly (w/o Double Locking System):


      1. B008M4J

        Remove the door lock wiring harness seal from the front door lock with motor assembly.

    6. When reusing the front door lock with motor assembly (w/ Double Locking System):


      1. B008MBL

        Remove the door lock wiring harness seal from the front door lock with motor assembly.

  16. REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY (w/o Double Locking System)


    1. B008K92C02
      *a Protective Tape
      B008LJK Remove in this Direction

      Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.

    2. B008KH9

      Disengage the guides to remove the front door lock cover sub-assembly from the front door lock with motor assembly.

  17. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY


    1. w/o Double Locking System:


      1. B008KTV

        Disengage the guide to remove the front door lock remote control cable assembly from the front door lock with motor assembly.

    2. w/ Double Locking System:


      1. B008KND

        Disengage the guide to remove the front door lock remote control cable assembly from the front door lock with motor assembly.

  18. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY


    1. w/o Double Locking System:


      1. B008LAV

        Disengage the guide to remove the front door inside locking cable assembly from the front door lock with motor assembly.

    2. w/ Double Locking System:


      1. B008LV7C01
        *a Protective Tape
        B008LJK Remove in this Direction

        Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.

      2. B008KSZ

        Disengage the guide to remove the front door inside locking cable assembly from the front door lock with motor assembly.