FRONT SEAT ASSEMBLY(for Power Seat) REASSEMBLY

Info Added 2018-01-24

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.

PROCEDURE


  1. INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side)

    Click here

  2. INSTALL REAR UPPER NO. 2 SEAT TRACK COVER


    1. B008BL4

      Attach the 3 claws to install the rear upper No. 2 seat track cover.

  3. INSTALL REAR UPPER SEAT TRACK COVER


    1. B008BL7

      Attach the 3 claws to install the rear upper seat track cover.

  4. INSTALL POWER SEAT MOTOR ASSEMBLY (for Rear Lifter)

    Click here

  5. INSTALL POWER SEAT MOTOR ASSEMBLY (for Front Vertical)

    Click here

  6. INSTALL SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY


    1. B008BMK

      Attach the 8 hooks to install the separate type front seat cushion spring assembly to the front seat adjuster assembly LH.

    2. B008BJC

      for Front Passenger Side:

      Attach the 2 clamps to install the connector holder.

  7. INSTALL FRONT SEAT ADJUSTER ASSEMBLY LH


    1. B008BIP

      Using a T50 "TORX" socket wrench, install the front seat adjuster assembly LH with the 4 "TORX" bolts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

  8. INSTALL FRONT SEAT BELT INNER ANCHOR BRACKET COVER LH (for Front Passenger Side)


    1. B008BJ3

      Attach the guide to install the front seat belt inner anchor bracket cover LH with the screw.

  9. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)


    1. B008BK9

      Attach the guide to install the front seat lower cushion shield LH with the screw.

  10. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH (for Front Passenger Side)

    Tech Tips

    Use the same procedure described for the front seat lower cushion shield LH.

  11. INSTALL FRONT SEAT WIRE LH


    1. Attach the claw.

      B008BJ4

    2. Attach the 3 wire harness clamps.

    3. Connect the 3 connectors.

    4. B008BMN

      Attach the 2 wire harness clamps and connect the connector to install the front seat wire LH.

  12. INSTALL POSITION CONTROL ECU ASSEMBLY (for Driver Side)


    1. B008BIV

      Install the position control ECU assembly with the 2 bolts.

    2. Connect the 2 connectors.

  13. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH


    1. B008BLV

      Attach the claw to install the seat climate control controller LH.

  14. INSTALL POWER SEAT MOTOR ASSEMBLY (for Reclining)

    Click here

  15. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH

    Click here

  16. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH

    Click here

  17. INSTALL SEPARATE TYPE FRONT SEATBACK PAD


    1. B008BJS

      Install the separate type front seatback pad.

  18. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH

    Click here

  19. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. Temporarily install the separate type front seatback cover.

    2. B008BJUE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 3 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    3. B008BKWE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 3 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    4. B008BKLE02
      Text in Illustration
      *1 Hog Ring Pliers
      *2 Hog Ring
      *3 Hook

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    5. Attach the 2 hooks.

    6. B008BMLE02
      Text in Illustration
      *1 Hog Ring Pliers
      *2 Strap

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 5 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

      • When installing the separate type front seatback cover, make sure to pass the straps of the separate type front seatback cover through the hog rings.

    7. B008BJY

      Attach the 2 claws to install the 2 front seat headrest supports.

    8. B008BLY

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

    9. B008BJW

      Attach the 2 hooks.

    10. B008BLT

      Attach the 2 hooks to connect the 2 straps.

    11. B008BJN

      Attach the 2 hooks at the bottom of the separate type front seatback cover.

    12. B008BLL

      Attach the 2 hooks.

  20. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY LH

    Tech Tips

    Perform this procedure when it is necessary to remove and reinstall or replace the separate type front seatback assembly LH.


    1. B008BL3

      Using a T50 "TORX" socket wrench, install the separate type front seatback assembly to the front seat adjuster assembly LH with the 4 "TORX" bolts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }
    2. B008BKP

      Connect the connector and attach the 2 wire harness clamps.

    3. B008BIM

      for Driver side:

      Connect the connector.

    4. B008BLY

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

    5. B008BJW

      Attach the 2 hooks.

    6. B008BLT

      Attach the 2 hooks to connect the 2 straps.

    7. B008BJN

      Attach the 2 hooks at the bottom of the separate type front seatback cover.

    8. B008BLL

      Attach the 2 hooks.

    9. B008BK3

      Attach the claw and connect the connector.

    10. Attach the 2 wire harness clamps.

  21. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH

    Click here

  22. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. B008BIG

      Attach the 13 hooks to install the separate type front seat cushion cover to the separate type front seat cushion pad.

      Note


      • Be careful not to damage the separate type front seat cushion cover.

      • When attaching the hooks, avoid wrinkling the separate type front seat cushion cover.

  23. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD


    1. Attach the 6 hooks to install the seat cushion cover with pad.

      B008BJB

    2. Connect the connector.

    3. B008BKH

      Attach the wire harness clamp.

    4. B008BIO

      for Front Passenger Side:

      Attach the claw to connect the connector.

    5. B008BIL

      Connect the connector.

    6. B008BIX

      Attach the claw to connect the connector.

    7. Attach the wire harness clamp.

    8. Connect the 2 connectors.

    9. B008BM2

      Attach the 2 hooks.

  24. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. B008BM4

      Attach the hook to install the front seat inner cushion shield LH with the screw.

  25. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)

    Click here

  26. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)

    Click here

  27. INSTALL SEAT SLIDE POSITION SENSOR PROTECTOR (for Driver Side)


    1. B008BK6

      Attach the 2 clamps and connect the wire harness.

    2. B008BKT

      Attach the 2 claws and 2 guides to install the seat slide position sensor protector with the screw.

  28. INSTALL FRONT POWER SEAT SWITCH LH

    Click here

  29. INSTALL LUMBAR FRONT POWER SEAT SWITCH (for Driver Side)

    Click here

  30. INSTALL FRONT SEAT NO. 1 INNER CUSHION SHIELD LH


    1. B008BKV

      Attach the 2 claws to install the front seat No. 1 inner cushion shield LH to the front seat cushion shield LH.

  31. INSTALL FRONT SEAT CUSHION SHIELD LH WITH FRONT SEAT NO. 1 INNER CUSHION SHIELD LH


    1. B008BM8

      for Driver Side:

      Connect the connector.

    2. B008BMB

      Attach the hook to install the front seat cushion shield LH with front seat inner No. 1 cushion shield LH.

    3. Install the 2 screws.

    4. B008BMC

      Attach the 2 claws and install the 2 screws.

    5. B008BMG

      Attach the 2 rubber bands.

  32. INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    1. B008BJ9

      Attach the 4 claws to install the slide and vertical power seat switch knob.

  33. INSTALL RECLINING POWER SEAT SWITCH KNOB


    1. B008BLK

      Attach the 2 claws to install the reclining power seat switch knob.