GENERATOR(for 130 A Type) REASSEMBLY

PROCEDURE

1. INSTALL GENERATOR DRIVE END FRAME BEARING

   1. 

      Using SST and a press, press in a new generator drive end frame bearing.

      09950-60010

      09951-00470

      09950-70010

      09951-07100

   2. 

      *a	Tab
      *b	Cutout

      Fit the tabs on the retainer plate into the cutouts on the generator drive end frame to install the retainer plate.

   3. Install the 4 screws.

      2.3 N*m

      23 kgf*cm

      20 in.*lbf

2. INSTALL GENERATOR ROTOR ASSEMBLY

   1. Place the generator drive end frame on the generator pulley with clutch.

   2. Install the generator rotor assembly to the generator drive end frame.

3. INSTALL GENERATOR BEARING COVER PACKING

   Note:

   A new generator coil assembly comes with a generator bearing cover packing. Therefore, it is not necessary to install a new generator bearing cover packing when installing a new generator coil assembly.

   1. 

      *a	Protrusion
      *b	Groove

      Install a new generator bearing cover packing to the generator coil assembly.

      Note:

      Align the protrusion of the generator bearing cover packing with the groove of the generator coil assembly when installing.

4. INSTALL GENERATOR COIL ASSEMBLY

   1. 

      *a	Deep Socket Wrench (21 mm)

      Using a 21 mm deep socket wrench and press, slowly press in the generator coil assembly.

   2. Install the generator coil assembly with the 4 bolts.

      5.6 N*m

      57 kgf*cm

      50 in.*lbf

5. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

   1. 

      *a

      Pin

      While pushing the 2 brushes into the generator brush holder assembly, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the brush holder hole.

   2. 

      *a

      Pin

      Install the generator brush holder assembly to the generator coil assembly with the 2 screws.

      1.8 N*m

      18 kgf*cm

      16 in.*lbf

   3. Pull out the pin from the generator brush holder assembly.

6. INSTALL GENERATOR TERMINAL INSULATOR

   1. 

      Install the generator terminal insulator to the generator coil assembly.

      Note:

      Make sure that the generator terminal insulator is installed with the correct orientation.

7. INSTALL GENERATOR REAR END COVER

   1. Install the generator rear end cover to the generator coil assembly with the 3 bolts.

      4.6 N*m

      47 kgf*cm

      41 in.*lbf

8. INSTALL GENERATOR PULLEY WITH CLUTCH

   1. Mount the generator assembly in a vise between aluminum plates.

   2. Temporarily install the generator pulley with clutch by hand.

   3. 

      *a	Generator Rotor Shaft

      Install SST A and B to the generator pulley with clutch as shown in the illustration.

      09820-63021

      Note:

      Securely attach SST to the generator pulley with clutch and generator rotor shaft.

   4. 

      *a	Hold
      *b	Torque Wrench Fulcrum Length
      *c	SST Fulcrum Length
      	Turn

      Using a wrench to hold SST A, turn SST B clockwise to tighten the generator pulley with clutch.

      Specified tightening torque

      80 N*m

      816 kgf*cm

      59 ft.*lbf

      Note:

      Be careful as the generator pulley with clutch or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.

      Tip:

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Click hereClick here

      • When using SST (fulcrum length of 100 mm (3.94 in.)) + torque wrench (fulcrum length of 400 mm (15.8 in.)):

        64 N*m (653 kgf*cm, 47 ft.*lbf)

   5. Remove SST from the generator assembly.

   6. Check that the generator pulley with clutch rotates smoothly.

   7. Remove the generator assembly from a vice.

9. INSTALL GENERATOR PULLEY CAP

   1. Install a new generator pulley cap to the generator pulley with clutch.