FRONT SEAT SIDE AIRBAG ASSEMBLY(for Manual Seat) REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are installed, removed or replaced during the front seat airbag assembly removal/installation are shown below.

Necessary procedure after parts removed/installed/replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative Functions when not Performed Link
Disconnect cable from negative (-) battery terminal Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) Stop and start system

for 2AR-FE:

Click here

for 2GR-FKS:

Click here

Memorize steering angle neutral point Panoramic view monitor system

Click here

Initialize servo motor Air conditioning system

Click here

Reset slide door close position Power slide door system

Click here

Reset back door close position Back door opener

Click here

Initialize back door lock Power door lock control system

Click here

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the RH side.

PROCEDURE


  1. PRECAUTION

    CAUTION:


    • B006M99

      Be sure to read Precaution thoroughly before servicing.

      Click here

    • B006LWS

      Wear protective gloves. Sharp areas on the parts may injure your hands.

    • There is risk of injury.

    • If the front seat side airbag was deployed, replace the front seat airbag assembly, separate type front seatback frame sub-assembly, separate type front seatback cover and separate type front seatback pad with the necessary parts in accordance with the extent of the collision damage.

    • Replace any other damaged parts as necessary.

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    CAUTION:


    • Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B006LHC

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE FRONT SEAT ASSEMBLY

    Click here

  4. REMOVE FRONT SEAT LEG ASSEMBLY RH

    Click here

  5. REMOVE FRONT NO. 1 SEAT LEG COVER

    Click here

  6. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH

    Click here

  7. REMOVE VERTICAL ADJUSTING HANDLE RH (w/ Vertical Adjuster)

    Click here

  8. REMOVE FRONT SEAT CUSHION SHIELD RH

    Click here

  9. REMOVE FRONT SEAT INNER CUSHION SHIELD RH

    Click here

  10. REMOVE NO. 1 SEAT ARMREST CAP

    Click here

  11. REMOVE FRONT SEAT INNER ARMREST ASSEMBLY RH

    Click here

  12. REMOVE FRONT SEATBACK HOOK

    Click here

  13. REMOVE FRONT SEAT HEADREST SUPPORT

    Click here

  14. REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD

    Click here

  15. REMOVE SEATBACK FELT

    Click here

  16. REMOVE FRONT SEAT AIRBAG ASSEMBLY RH

    CAUTION:


    • When storing the front seat airbag assembly RH, keep the airbag deployment side facing upward.

    • If the airbag deploys for any reason, it may cause a serious accident.

    B006QV5C01
    B006PCE Deployment Side

    1. B006LJYC01
      *a Housing Lock
      *b CPA
      *c CPA Upper Part
      B006N8A Disconnect in this Direction

      Disconnect the airbag connector.

      Note

      When disconnecting any airbag connector, take care not to damage the airbag wire harness.


      1. B006L9QC01
        *a Housing Lock
        B006PCE CPA
        B006N8A Slide in this Direction

        Push down the housing lock and slide the CPA. (At this time, the airbag connector cannot be disconnected yet.)

      2. Push down the housing lock again and disconnect the airbag connector.

        Note

        Do not push down the upper part of the CPA shown in the illustration when disconnecting the airbag connector.

    2. Detach the wire harness clamp.

    3. Detach the claw and disconnect the airbag connector.

    4. B006QZN

      Detach the wire harness clamp.

    5. B006O43C01
      B006PCE Fastener

      Detach the fastener and wire harness clamp.

    6. B006PCP

      Remove the 2 nuts and front seat airbag assembly RH.

      Note


      • The nuts must not be reused.

      • Make sure that the separate type front seatback frame sub-assembly is not deformed. If it is, replace it with a new one.