CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed, installed or replaced during the front bumper assembly removal/installation are shown below.
Replacement Part or Procedure | Necessary Procedures | Effects / Inoperative when not Performed | Link |
---|---|---|---|
Disconnect cable from negative (-) auxiliary battery terminal | Memorize steering angle neutral point | LKA/LDA system (for Mono camera type) | for Mono Camera type: for Stereo Camera type: |
Lane control system (for Stereo camera type) | |||
Parking support brake system* | |||
Pre-collision system (for Stereo camera type) | |||
Pre-collision system (for Mono camera type) | |||
Adaptive high beam system | |||
Lighting system (EXT) |
|||
Variable gear ratio steering system | |||
Parking assist monitor system | |||
Panoramic view monitor system | |||
Initialize rear door sunshade system | Rear door sunshade system | ||
Initialize power trunk lid system | Power trunk lid system | ||
Front bumper assembly (Including removal and installation) |
|
Parking support brake system | |
Front television camera view adjustment | Panoramic view monitor system | ||
w/ Parking Support Brake System |
|
|
|
|
Front television camera view adjustment | Panoramic view monitor system |
Tech Tips
When the front bumper is damaged or deformed due to an accident or contact with other objects, etc., or the bumper installation area on the body is repaired, it is necessary to perform millimeter wave radar sensor adjustment.
If the bumper is damaged, there is a possibility that the installation area of the front side radar sensor may be deformed and the front side radar sensor system may not operate correctly, so visually inspect the front side radar sensor installation area (headlight, frame, bracket, stud bolt) to make sure it is not dented or bent.
If the visual inspection finds a problem, check the installation condition of the front side radar sensor, and adjust the installation position of the front side radar sensor as necessary.
PROCEDURE
PRECAUTION
Note
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
w/ Grille Shutter:
Change the grille shutter control mode to maintenance mode.
Note
Make sure to change the grille shutter control mode to maintenance mode to prevent the grill shutter from opening or closing when the power switch is off.
REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY
DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
REMOVE UPPER RADIATOR SUPPORT SEAL
REMOVE RADIATOR COVER PLATE
REMOVE LOWER RADIATOR AIR DEFLECTOR
REMOVE FRONT BUMPER ASSEMBLY
Remove the 3 bolts.
Remove the 4 clips.
Tech Tips
Use the same procedure for the RH and LH side.
*1 | Front Bumper Seal Bracket |
Remove the screw.
Tech Tips
Use the same procedure for the RH and LH side.
Remove the front bumper seal bracket.
Tech Tips
Use the same procedure for the RH and LH side.
Remove the 8 screws.
Disconnect the 2 connectors.
Protective Tape |
Put protective tape around the front bumper assembly.
Place hands here | |
Remove in this Direction (1) | |
Remove in this Direction (2) |
Detach the claw and clip while pulling toward the outside of the vehicle and remove the front bumper assembly as shown in the illustration.
Tech Tips
Use the same procedure for the RH and LH side.
Remove in this Direction |
Detach the claw and remove the front bumper assembly.
w/ Headlight Cleaner System:
Disconnect the headlight cleaner hose.
Tech Tips
Prepare a container before performing the procedure.