PROCEDURE
INSTALL NO. 2 MANIFOLD CONVERTER INSULATOR
Install the 2 No. 2 manifold converter insulators to the exhaust manifold assembly with the 8 bolts.
INSTALL NO. 1 MANIFOLD CONVERTER INSULATOR
Install the 2 No. 1 manifold converter insulators to the exhaust manifold assembly with the 8 bolts.
INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
Install the 2 No. 1 exhaust manifold heat insulators to the exhaust manifold assembly with the 6 bolts.
INSTALL EXHAUST MANIFOLD ASSEMBLY RH
*A | Bank 1 Sensor 1 Side |
*B | Bank 1 Sensor 2 Side |
*a | Torque Wrench Fulcrum Length |
Using SST, install the air fuel ratio sensor to the exhaust manifold assembly RH.
Torque |
---|
Specified tightening torque |
44 N*m (449 kgf*cm, 32 ft.*lbf) |
Note
Replace with a new part if it is dropped or if it receives a strong impact.
Tech Tips
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 37.7 N*m (384 kgf*cm, 28 ft.*lbf)
Install a new gasket to the cylinder head sub-assembly.
Temporarily install the exhaust manifold assembly RH with 4 new nuts.
Tighten the 4 nuts in the sequence shown in the illustration.
INSTALL EXHAUST MANIFOLD ASSEMBLY LH
*A | Bank 2 Sensor 1 Side |
*B | Bank 2 Sensor 2 Side |
*a | Torque Wrench Fulcrum Length |
Using SST, install the air fuel ratio sensor to the exhaust manifold assembly LH.
Torque |
---|
Specified tightening torque |
44 N*m (449 kgf*cm, 32 ft.*lbf) |
Note
Replace with a new part if it is dropped or if it receives a strong impact.
Tech Tips
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
When using SST (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 37.7 N*m (384 kgf*cm, 28 ft.*lbf)
Install a new gasket to the cylinder head sub-assembly LH.
Temporarily install the exhaust manifold assembly LH with 4 new nuts.
Tighten the 4 nuts in the sequence shown in the illustration.
CONNECT AIR FUEL RATIO SENSOR
for Bank 1 Sensor 1:
Connect the connector.
Attach the 3 wire harness clamps.
for Bank 1 Sensor 2:
Connect the connector.
Attach the 2 wire harness clamps.
for Bank 2 Sensor 1:
Connect the connector.
Attach the 4 wire harness clamps.
for Bank 2 Sensor 2:
Connect the connector.
Attach the 3 wire harness clamps.
INSTALL FENDER APRON BRACE SUB-ASSEMBLY RH
Install the fender apron brace sub-assembly RH to the body with the 2 bolts.
Attach the clamp and connect the hose to the fender apron brace sub-assembly RH.
INSTALL FENDER APRON BRACE SUB-ASSEMBLY LH
Install the fender apron brace sub-assembly LH to the body with the 2 bolts.
Attach the clamp and connect the hose to the fender apron brace sub-assembly LH.
INSTALL REAR LOWER ARM MOUNTING REINFORCEMENT SUB-ASSEMBLY RH
Install the rear lower arm mounting reinforcement sub-assembly RH with the 4 bolts.
INSTALL ENGINE SIDE COVER RH
Attach the 4 clips to install the engine side cover RH.
INSTALL NO. 1 EXHAUST PIPE SUPPORT BRACKET SUB-ASSEMBLY
Install the No. 1 exhaust pipe support bracket sub-assembly with the 2 bolts.
INSTALL FRONT EXHAUST PIPE ASSEMBLY
INSTALL FRONT CENTER FLOOR BRACE SUB-ASSEMBLY
INSTALL FLOOR BOARD SUB-ASSEMBLY
INSTALL NO. 2 FLOOR BOARD SUB-ASSEMBLY
INSTALL REAR FLOOR SIDE MEMBER COVER RH
INSTALL REAR FLOOR SIDE MEMBER COVER LH
INSTALL STRUT BAR BRACKET SUPPORT SUB-ASSEMBLY
INSTALL FRONT SUSPENSION MEMBER BRACE
INSTALL NO. 2 ENGINE UNDER COVER ASSEMBLY
INSTALL TRANSMISSION UNDER COVER
INSTALL NO. 1 ENGINE UNDER COVER ASSEMBLY
INSTALL FRONT FENDER APRON INSULATOR LH
Install the front fender apron insulator LH with the 3 bolts.
INSTALL NO. 2 ENGINE OIL LEVEL DIPSTICK GUIDE
Install a new O-ring to the No. 2 engine oil level dipstick guide.
Install the No. 2 engine oil level dipstick guide with the bolt.
Install the engine oil level dipstick to the No. 2 engine oil level dipstick guide.
INSTALL AIR CLEANER WITH AIR CLEANER HOSE
INSTALL NO. 1 AIR CLEANER INLET
INSTALL RADIATOR SUPPORT TO CROSSMEMBER BRACE SUB-ASSEMBLY RH
Install the radiator support to crossmember brace sub-assembly RH with the 2 bolts.
INSTALL RADIATOR SUPPORT TO CROSSMEMBER BRACE SUB-ASSEMBLY LH
Install the radiator support to crossmember brace sub-assembly LH with the 2 bolts.
INSTALL LOWER RADIATOR AIR DEFLECTOR
Attach the 7 clips to install the lower radiator air deflector.
INSTALL UPPER RADIATOR SUPPORT SEAL
Attach the 7 clips to install the upper radiator support seal.
INSTALL RADIATOR COVER PLATE
Attach the 7 clips to install the radiator cover plate.
INSTALL V-BANK COVER SUB-ASSEMBLY
INSPECT FOR EXHAUST GAS LEAK