Tech Tips
Each ECM terminal's standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.
Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
---|---|---|---|---|
G86-1 (BATT) - C60-1 (E1) | Y - W-B | Battery (for measuring the battery voltage and for the ECM memory) | Always | 11 to 14 V |
G86-18 (IGSW) - C60-1 (E1) | GR - W-B | Ignition switch | Ignition switch ON | 11 to 14 V |
G86-2 (+B) - C60-1 (E1) | L - W-B | Power source of ECM | Ignition switch ON | 11 to 14 V |
G86-3 (+B2) - C60-1 (E1) | B - W-B | Power source of ECM | Ignition switch ON | 11 to 14 V |
G86-4 (+B3) - C60-1 (E1) | B - W-B | Power source of ECM | Ignition switch ON | 11 to 14 V |
G85-14 (MREL) - C60-1 (E1) | W - W-B | EFI-MAIN NO. 1 relay operation signal | Ignition switch ON | 11 to 14 V |
10 seconds elapsed after ignition switch off | 0 to 1.5 V | |||
C59-5 (+BD1) - C60-1 (E1) | B - W-B | EDU relay operation signal | Ignition switch ON | 11 to 14 V |
C59-4 (+BD2) - C60-1 (E1) | B - W-B | EDU relay operation signal | Ignition switch ON | 11 to 14 V |
G85-15 (GREL) - C60-1 (E1) | LG - W-B | GLOW relay | Cranking | 11 to 14 V |
Idling (10 seconds or more after engine start) | 0 to 1.5 V | |||
G85-11 (NSW) - C60-1 (E1) | L - W-B | Park/Neutral position switch assembly signal*1 | Ignition switch ON, shift lever not in P or N | 11 to 14 V |
Ignition switch ON, shift lever in P or N | Below 1.0 V | |||
Clutch start switch signal*2 | Ignition switch ON, clutch pedal fully depressed | Below 1.0 V | ||
Ignition switch ON, clutch pedal released | 11 to 14 V | |||
G86-29 (VCPA) - G86-22 (EPA) | LG - G | Power source of accelerator pedal position sensor (for VPA) | Ignition switch ON | 4.5 to 5.5 V |
G86-30 (VCP2) - G86-25 (EPA2) | R - Y | Power source of accelerator pedal position sensor (for VPA2) | Ignition switch ON | 4.5 to 5.5 V |
G86-28 (VPA) - G86-22 (EPA) | W - G | Accelerator pedal position sensor signal (for engine control) | Ignition switch ON, accelerator pedal fully released | 0.5 to 1.1 V |
Accelerator pedal position sensor signal (for engine control) | Ignition switch ON, accelerator pedal fully depressed | 3.0 to 4.6 V | ||
G86-31 (VPA2) - G86-25 (EPA2) | GR - Y | Accelerator pedal position sensor signal (for sensor malfunction detection) | Ignition switch ON, accelerator pedal fully released | 0.9 to 2.3 V |
Accelerator pedal position sensor signal (for sensor malfunction detection) | Ignition switch ON, accelerator pedal fully depressed | 3.4 to 5.0 V | ||
C58-25 (VCVG) - C58-24 (EVG) | L - Y | Power source of mass air flow meter sub-assembly (for VG) | Ignition switch ON | 4.8 to 5.2 V |
C58-33 (VG) - C58-24 (EVG) | W - Y | Mass air flow meter sub-assembly signal | Ignition switch ON | Pulse generation (See waveform 1) |
C58-32 (THA) - C58-24 (EVG) | B - Y | Intake air temperature sensor (built into mass air flow meter sub-assembly) | Idling, intake air temperature at 20°C (68°F) | 0.5 to 3.4 V |
C58-35 (THIA) - C58-27 (ETHI) | G - BR | Intake air temperature sensor (turbo) | Idling, intake air temperature at 0 to 80°C (32 to 176°F) | 0.5 to 3.4 V |
C57-34 (THW) - C57-27 (ETHW) | B - BR | Engine coolant temperature sensor | Idling, engine coolant temperature at 80°C (176°F) | 0.2 to 1.0 V |
G85-22 (STA) - C60-1 (E1) | GR - W-B | Starter signal | Cranking | 6.0 V or higher |
C57-6 (#1D+) - C57-7 (#1D-) | W - B | No. 1 Injector assembly signal | Idling | Pulse generation (See waveform 2) |
C57-1 (#2D+) - C57-2 (#2D-) | R - W | No. 2 Injector assembly signal | ||
C58-7 (#3D+) - C58-6 (#3D-) | G - R | No. 3 Injector assembly signal | ||
C57-5 (#4D+) - C57-4 (#4D-) | Y - L | No. 4 Injector assembly signal | ||
C60-17 (VCG) - C60-18 (G2-) | B - W | Power source of camshaft position sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
C60-27 (G2+) - C60-18 (G2-) | R - W | Camshaft position sensor signal | Idling | Pulse generation (See waveform 3) |
C60-20 (VCNE) - C60-19 (NE-) | W - R | Power source of crankshaft position sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
C60-28 (NE+) - C60-19 (NE-) | Y - R | Crankshaft position sensor signal | Idling | Pulse generation (See waveform 4) |
G86-13 (STP) - C60-1 (E1) | L - W-B | Stop light switch assembly signal | Ignition switch ON, brake pedal depressed | 7.5 to 14 V |
Ignition switch ON, brake pedal released | 0 to 1.5 V | |||
G86-12 (ST1-) - C60-1 (E1) | GR - W-B | Stop light switch assembly signal (opposite to STP) |
Ignition switch ON, brake pedal depressed | 0 to 1.5 V |
Ignition switch ON, brake pedal released | 7.5 to 14 V | |||
G85-25 (TC) - C60-1 (E1) | R - W-B | Terminal TC of DLC3 | Ignition switch ON | 11 to 14 V |
G85-10 (SPD) - C60-1 (E1) | V - W-B | Speed signal from combination meter assembly | Ignition switch ON, slowly wheel rotated | Pulse generation (See waveform 5) |
C57-28 (VCPM) - C57-19 (EPIM) | R - BR | Power source of manifold absolute pressure sensor (specific voltage) | Ignition switch ON | 4.5 to 5.5 V |
C57-18 (PIM) - C57-19 (EPIM) | L - BR | Manifold absolute pressure sensor | Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied | 0.1 to 0.7 V |
Same as atmospheric pressure | 0.8 to 1.5 V | |||
Positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg) applied | 1.6 to 2.3 V | |||
G85-16 (TACH) - C60-1 (E1) | V - W-B | Engine speed | Idling | Pulse generation (See waveform 6) |
C59-28 (VCM) - C59-19 (E2M) | G - R | Power source of fuel pressure sensor (for PCR1) | Ignition switch ON | 4.5 to 5.5 V |
C59-18 (PCR1) - C59-19 (E2M) | W - R | Fuel pressure sensor signal (main) | Idling | 1.8 to 2.1 V |
C60-33 (VCS) - C60-25 (E2S) | B - P | Power source of fuel pressure sensor (for PCR2) | Ignition switch ON | 4.5 to 5.5 V |
C60-26 (PCR2) - C60-25 (E2S) | R - P | Fuel pressure sensor signal (sub) | Idling | 1.3 to 1.6 V |
C58-3 (PCV+) - C58-4 (PCV-) | G - R | Pre-stroke control valve operation signal | Idling | Pulse generation (See waveform 7) |
C58-2 (PRV+) - C58-1 (PRV-) | B - Y | Pressure discharge valve signal | Ignition switch turned off after idling | Pulse generation |
C59-1 (VNM+) - C60-1 (E1) | G - W-B | DC motor signal (turbocharger nozzle vane control actuator) | Idling | Pulse generation |
C59-2 (VNM-) - C60-1 (E1) | W - W-B | DC motor signal (turbocharger nozzle vane control actuator) | Idling | Pulse generation |
C59-30 (VNVC) - C59-22 (VNE2) | R - W | Power source of nozzle vane position sensor (turbocharger nozzle vane control actuator) | Ignition switch ON | 4.5 to 5.5 V |
C59-23 (VNA) - C59-22 (VNE2) | P - W | Nozzle vane position sensor signal (turbocharger nozzle vane control actuator) | Ignition switch ON | 2.3 to 2.7 V |
C59-29 (VCVL) - C59-20 (EVLU) | Y - L | Power source of throttle position sensor | Ignition switch ON | 4.5 to 5.5 V |
C59-21 (VLU) - C59-20 (EVLU) | W- L | Throttle position sensor signal | Ignition switch ON, throttle valve fully opened |
3.6 to 4.2 V |
Ignition switch ON, throttle valve fully closed |
0.4 to 1.0 V | |||
C60-6 (M+) - C60-3 (ME01) | G - W-B | Diesel throttle duty signal | Engine warmed up, racing engine | Pulse generation |
C60-5 (M-) - C60-3 (ME01) | R - W-B | Diesel throttle duty signal | Engine warmed up, racing engine | Pulse generation |
G85-23 (NEO) - C60-1 (E1) | G - W-B | Crankshaft position sensor signal sent to certification ECU (smart key ECU assembly) | Engine warmed up, idling | Pulse generation (See waveform 8) |
G86-15 (AC1) - C59-3 (E01) | GR - W-B | A/C signal | A/C switch on | 0 to 1.5 V |
A/C switch off | 11 to 14 V | |||
G86-14 (ACT) - C59-3 (E01) | LG - W-B | A/C signal | Ignition switch ON | 11 to 14 V |
A/C cut control on | 0 to 3 V | |||
G85-28 (CANL) - C60-1 (E1) | W - W-B | CAN communication line | Ignition switch ON | Pulse generation (See waveform 9) |
G85-17 (CANH) - C60-1 (E1) | B - W-B | CAN communication line | Ignition switch ON | Pulse generation (See waveform 10) |
C60-7 (LIN) - C60-1 (E1) | P - W-B | LIN communication line | Ignition switch ON | Pulse generation (See waveform 11) |
C59-3 (E01) - Body ground | W-B - Body ground | Earth (ground) circuit of ECM | Always | Below 1 Ω |
C60-4 (E02) - Body ground | W-B - Body ground | Earth (ground) circuit of ECM | Always | Below 1 Ω |
C60-1 (E1) - Body ground | W-B - Body ground | Earth (ground) circuit of ECM | Always | Below 1 Ω |
C60-3 (ME01) - Body ground | W-B - Body ground | Earth (ground) circuit of ECM | Always | Below 1 Ω |
G86-8 (EC) - Body ground | BR - Body ground | Earth (ground) circuit of ECM | Always | Below 1 Ω |
C57-3 (E1D1) - Body ground | W-B - Body ground | Earth (ground) circuit of ECM | Always | Below 1 Ω |
C58-5 (E1D2) - Body ground | W-B - Body ground | Earth (ground) circuit of ECM | Always | Below 1 Ω |
C60-2 (E04) - Body ground | W-B - Body ground | Earth (ground) circuit of ECM | Always | Below 1 Ω |
*1: for Automatic Transmission
*2: for Manual Transmission
WAVEFORM 1
*a | 1 V/DIV. |
*b | 100 μsec./DIV. |
ECM Terminal Name | Between VG and EVG |
Tester Range | 1 V/DIV., 100 μsec./DIV. |
Condition | Ignition switch ON |
WAVEFORM 2
*a | 10 V/DIV. |
*b | 1 msec./DIV. |
ECM Terminal Name | Between #1D+ and #1D- Between #2D+ and #2D- Between #3D+ and #3D- Between #4D+ and #4D- |
Tester Range | 10 V/DIV., 1 msec./DIV. |
Condition | Idling with warm engine |
Tech Tips
The waveform varies depending on the injector injection.
WAVEFORM 3
*a | 5 V/DIV. |
*b | 20 msec./DIV. |
ECM Terminal Name | Between G2+ and G2- |
Tester Range | 5 V/DIV., 20 msec./DIV. |
Condition | Idling with warm engine |
Tech Tips
The waveform varies depending on the engine speed.
WAVEFORM 4
*a | 2 V/DIV. |
*b | 10 msec./DIV. |
ECM Terminal Name | Between NE+ and NE- |
Tester Range | 2 V/DIV., 10 msec./DIV. |
Condition | Idling with warm engine |
Tech Tips
The waveform becomes shorter as the engine speed.
WAVEFORM 5
*a | 5 V/DIV. |
*b | 10 msec./DIV. |
ECM Terminal Name | Between SPD and E1 |
Tester Range | 5 V/DIV., 10 msec./DIV. |
Condition | Driving at vehicle speed of 40 km/h (25 mph) |
Tech Tips
The wavelength becomes shorter as the vehicle speed increases.
WAVEFORM 6
*a | 5 V/DIV. |
*b | 10 ms./DIV. |
ECM Terminal Name | Between TACH and E1 |
Tester Range | 5 V/DIV., 10 ms./DIV. |
Condition | Idling with warm engine |
Tech Tips
The wavelength becomes shorter as the engine speed increases.
WAVEFORM 7
*1 | 10 V/DIV. |
*2 | 20 msec./DIV. |
ECM Terminal Name | Between PCV+ and PCV- |
Tester Range | 10 V/DIV., 20 msec./DIV. |
Condition | Idling with warm engine |
Tech Tips
The waveform varies depending on pre-stroke control valve operation.
WAVEFORM 8
*a | 1 V/DIV. |
*b | 2 msec./DIV. |
ECM Terminal Name | Between NEO and E1 |
Tester Range | 1 V/DIV., 2 msec./DIV. |
Condition | Idling with warm engine |
WAVEFORM 9
*a | 1 V/DIV. |
*b | 10 msec./DIV. |
ECM Terminal Name | Between CANL and E1 |
Tester Range | 1 V/DIV., 10 msec./DIV. |
Condition | Engine stopped, ignition switch ON |
Tech Tips
The waveform varies depending on the CAN communication signal.
WAVEFORM 10
*a | 1 V/DIV. |
*b | 10 msec./DIV. |
ECM Terminal Name | Between CANH and E1 |
Tester Range | 1 V/DIV., 10 msec./DIV. |
Condition | Engine stopped, ignition switch ON |
Tech Tips
The waveform varies depending on the CAN communication signal.
WAVEFORM 11
*a | 2 V/DIV. |
*b | 10 msec./DIV. |
ECM Terminal Name | Between LIN and E1 |
Tester Range | 2 V/DIV., 10 msec./DIV. |
Condition | Engine stopped, ignition switch ON |
Tech Tips
The waveform varies depending on the LIN communication signal.