PROCEDURE
INSTALL STUD BOLT
Using an E8 "TORX" socket wrench, install the stud bolts.
INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY
Using a 5 mm hexagon wrench, install the 4 No. 1 oil nozzle sub-assemblies with the 4 bolts.
INSTALL PISTON WITH PIN SUB-ASSEMBLY
*1 | Service Hole |
Using a small screwdriver, install a new snap ring at one end of the piston pin hole.
Tech Tips
Be sure that the end gap of the snap ring is not aligned with the service hole of the piston.
Gradually heat the piston to approximately 80°C (176°F).
Coat the piston pin and connecting rod with engine oil.
*1 | Front Mark |
Align the front marks of the piston and connecting rod as shown in the illustration. Then push in the piston pin with your thumb until the piston pin contacts the snap ring.
Tech Tips
The piston and pin are a matched set.
Note
For the LH side, perform the assembly so that the front marks of the piston and connecting rod are on the same side. For the RH side, perform the assembly so that the front marks of the piston and connecting rod are on opposite sides.
Check the fitting condition between the piston and piston pin.
Move the connecting rod back and forth on the piston pin. Check the fitting condition.
If abnormal movement is felt, replace the piston and pin as a set.
Rotate the piston back and forth on the piston pin. Check the fitting condition.
If abnormal movement is felt, replace the piston and pin as a set.
*1 | Service Hole |
Using a small screwdriver, install a new snap ring at the other end of the piston pin hole.
Tech Tips
Be sure that the end gap of the snap ring is not aligned with the service hole of the piston.
INSTALL PISTON RING SET
*1 | Side Rail Upper |
*2 | Side Rail Lower |
*3 | Oil Ring Expander |
Install the oil ring expander, side rail upper and side rail lower by hand.
*1 | No. 1 Compression Ring |
*2 | No. 2 Compression Ring |
*3 | Paint Mark |
Top |
Using a piston ring expander, install the No. 1 compression ring and No. 2 compression ring so that the paint marks are positioned as shown in the illustration.
Paint Mark | ||||||
---|---|---|---|---|---|---|
|
INSTALL CRANKSHAFT BEARING
*1 | No. 1 and No. 5 Journal Bearings |
*2 | No. 2, No. 3 and No. 4 Journal Bearings |
Clean the main journal and both surfaces of the bearing.
Install the upper crankshaft bearing.
Note
Main bearings come in widths of 21 mm (0.827 in.) and 22.5 mm (0.886 in.). Install the 22.5 mm (0.886 in.) bearings in the No. 1 and No. 5 cylinder block journal positions with the main bearing caps. Install the 21 mm (0.827 in.) bearings in the No. 2, No. 3 and No. 4 positions.
*1 | Oil Groove |
*2 | Oil Feed Hole |
*a | CORRECT |
*b | INCORRECT |
Install the upper crankshaft bearing to the cylinder block sub-assembly as shown in the illustration.
Note
Do not apply engine oil to the bearings and the contact surfaces.
Both sides of the oil groove in the cylinder block sub-assembly should be visible through the oil feed holes in the crankshaft bearing. The amount visible on each side of the holes should be equal.
Do not allow coolant to come into contact with the bearing inner surface.
If any coolant comes into contact with the bearing inner surface, replace the crankshaft bearing with a new one.
*a | Vernier Caliper |
Install the lower bearing.
Note
Be sure to install the selected bearing.
Main bearings come in widths of 21 mm (0.827 in.) and 22.5 mm (0.886 in.). Install the 22.5 mm (0.886 in.) bearings in the No. 1 and No. 5 cylinder block journal positions with the main bearing caps. Install the 21 mm (0.827 in.) bearings in the No. 2, No. 3 and No. 4 positions.
Install the lower bearings to the crankshaft bearing caps.
Using a vernier caliper, measure the distance between the edge of the crankshaft bearing cap and the edge of the lower bearing.
Dimension A - B or B - A |
---|
0 to 0.7 mm (0 to 0.0276 in.) |
Note
Do not apply engine oil to the bearings and the contact surfaces.
Do not allow coolant to come into contact with the bearing inner surface.
If any coolant comes into contact with the bearing inner surface, replace the bearing with a new one.
INSTALL CRANKSHAFT THRUST WASHER SET
Apply engine oil to the crankshaft thrust washer set.
Install the 4 crankshaft thrust washers to the No. 3 journal position of the cylinder block sub-assembly and crankshaft bearing cap with the oil grooves facing outward.
INSTALL CRANKSHAFT
*1 | Number Mark |
Apply engine oil to the upper crankshaft bearing and lower crankshaft bearing, then place the crankshaft on the cylinder block sub-assembly.
Confirm the front marks and numbers of the crankshaft bearing caps, and install the crankshaft bearing caps on the cylinder block sub-assembly.
Tech Tips
A number is marked on each main bearing cap to indicate the installation position.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
Temporarily install the 10 crankshaft bearing cap bolts to the inside positions.
*1 | Less than 6 mm |
*2 | 91 mm |
Push the crankshaft bearing cap by hand until the clearance between the crankshaft bearing cap and cylinder block sub-assembly is less than 6 mm (0.236 in.).
Standard Bolt length |
---|
91 mm (3.58 in.) |
Using a plastic-faced hammer, lightly tap the crankshaft bearing cap to ensure a proper fit.
Apply a light coat of engine oil to the threads and under the heads of the 10 crankshaft bearing cap bolts.
*1 | 79.5 mm |
Temporarily install the 10 crankshaft bearing cap bolts to the outside positions.
Standard Bolt length |
---|
79.5 mm (3.13 in.) |
Tech Tips
The main bearing cap bolts are tightened in 2 progressive steps.
Step 1:
Uniformly tighten the 20 crankshaft bearing cap bolts in the sequence shown in the illustration.
If any of the main bearing cap bolts does not meet the specified torque, replace it.
Step 2:
*1 | Painted Mark |
*2 | Front |
Mark the front of the bearing cap bolts with paint.
Tighten the bearing cap bolts 90° in the order shown in step 1.
Check that the painted marks are now at a 90° angle to the front.
Check that the crankshaft turns smoothly.
Install and uniformly tighten the 10 crankshaft bearing cap bolts and 10 new seal washers in several steps in the sequence shown in the illustration.
Check that the crankshaft turns smoothly.
INSTALL CONNECTING ROD BEARING
*1 | Vernier Caliper |
Install the connecting rod bearings to the connecting rods and bearing caps.
Using a vernier caliper, measure the distance between the connecting rod and bearing cap edges, and each connecting rod bearing edge.
Dimension A - B or B - A |
---|
0 to 0.7 mm (0 to 0.0276 in.) |
Note
Do not apply engine oil to the bearings and the contact surfaces.
Do not allow coolant to come into contact with the bearing inner surface.
If any coolant comes into contact with the bearing inner surface, replace the connecting rod bearing with a new one.
INSTALL PISTON AND CONNECTING ROD
Apply engine oil to the cylinder walls, the pistons, and the surfaces of the connecting rod bearings.
Position the piston rings so that the ring ends are as shown in the illustration.
Tech Tips
The expander ends can be placed anywhere.
Note
Do not align the ring ends.
*1 | Front Mark |
Using a hammer handle and piston ring compressor, push the correctly numbered piston and connecting rod into the cylinder with the front mark of the piston facing forward.
Place the connecting rod cap on the connecting rod.
*1 | Front |
*2 | Front Mark |
Match the numbered connecting rod cap with the connecting rod.
Place the connecting rod cap on the connecting rod, and check that the front mark of the connecting rod cap is facing the direction indicated in the chart below.
Front Mark | ||||||
---|---|---|---|---|---|---|
|
Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.
Temporarily install the connecting rod cap bolts.
Tech Tips
The connecting rod cap bolts are tightened in 2 progressive steps.
Step 1:
Install and alternately tighten the bolts of the connecting rod cap in several steps.
*1 | Front |
*2 | Painted Mark |
Step 2:
Mark the front side of each connecting rod cap bolt with paint.
Tighten the cap bolts 90° as shown in the illustration in the order in step 1.
Check that the painted marks are now at a 90° angle to the front.
Check that the crankshaft turns smoothly.