DTC Code | DTC Name |
---|---|
P00AC | Intake Air Temperature Sensor 1 Circuit Low Bank 2 |
P00AD | Intake Air Temperature Sensor 1 Circuit High Bank 2 |
P0112 | Intake Air Temperature Circuit Low Input |
P0113 | Intake Air Temperature Circuit High Input |
DESCRIPTION
The intake air temperature sensor, mounted on the mass air flow meter sub-assembly, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (see Fig. 1).
The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.
Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes, according to changes in the intake air temperature, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.
Tech Tips
When DTC P00AC, P00AD, P0112 or P0113 is stored, the ECM enters fail-safe mode. During fail-safe mode, the intake air temperature is estimated to be 20°C (68°F) by the ECM. Fail-safe mode continues until a pass condition is detected.
DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
---|---|---|---|---|---|
P00AC | Intake Air Temperature Sensor 1 Circuit Low Bank 2 | A short in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
Comes on | DTC stored |
P00AD | Intake Air Temperature Sensor 1 Circuit High Bank 2 | An open in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
Comes on | DTC stored |
P0112 | Intake Air Temperature Circuit Low Input | A short in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
Comes on | DTC stored |
P0113 | Intake Air Temperature Circuit High Input | An open in the intake air temperature sensor circuit for 0.5 seconds (1 trip detection logic). |
|
Comes on | DTC stored |
Tech Tips
When any of these DTCs are output, check the intake air temperature using the GTS. Enter the following menus: Powertrain / Engine / Data List / All Date / Intake Air Temp B1S1 or Intake Air Temp B2S1.
Temperature Displayed | Malfunction |
---|---|
-40°C (-40°F) | Open circuit |
Higher than 128°C (262°F) | Short circuit |
MONITOR DESCRIPTION
The ECM monitors the sensor voltage and uses this value to calculate the intake air temperature. When the sensor output voltage deviates from the normal operating range, the ECM interprets this as a malfunction in the intake air temperature sensor circuit and stores a DTC.
Example:
If the sensor output voltage is higher than 4.91 V for 0.5 seconds or more, the ECM determines that there is an open in the intake air temperature sensor circuit, and stores DTC P00AD or P0113. Conversely, if the output voltage is less than 0.18 V for 0.5 seconds or more, the ECM determines that there is a short in the sensor circuit, and stores DTC P00AC or P0112.
MONITOR STRATEGY
Frequency of Operation | Continuous |
CONFIRMATION DRIVING PATTERN
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
Turn the engine switch off and wait for at least 30 seconds.
Turn the engine switch on (IG).
Turn the GTS on.
Wait 0.5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the pending DTCs.
Tech Tips
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P00AC, P00AD, P0112 or P0113.
Check the DTC judgment result.
GTS Display | Description |
---|---|
NORMAL |
|
ABNORMAL |
|
INCOMPLETE |
|
N/A |
|
Tech Tips
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.
CAUTION / NOTICE / HINT
Tech Tips
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
PROCEDURE
READ VALUE USING GTS (INTAKE AIR)
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Intake Air Temp B1S1 or Intake Air Temp B2S1.
Tester Display |
---|
Intake Air Temp B1S1 |
Intake Air Temp B2S1 |
Read the value displayed on the GTS.
OK |
---|
Same as actual intake air temperature. |
Result | ||||||||
---|---|---|---|---|---|---|---|---|
|
Tech Tips
If there is an open circuit, the GTS indicates -40°C (-40°F).
If there is a short circuit, the GTS indicates higher than 128°C (262°F).
B |
READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS) Click here |
C |
CHECK FOR INTERMITTENT PROBLEMS Click here |
A |
READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)
*1 | mass air flow meter sub-assembly |
*2 | ECM |
*a | Front view of wire harness connector (to mass air flow meter sub-assembly) |
*b | Bank 1 |
*c | Bank 2 |
Disconnect the mass air flow meter sub-assembly connector.
Connect terminals 4 (THA) and 2 (E2G) or 4 (THAR) and 2 (E2GR) of the mass air flow meter sub-assembly connector on the wire harness side.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Intake Air Temp B1S1 or Intake Air Temp B2S1.
Tester Display |
---|
Intake Air Temp B1S1 |
Intake Air Temp B2S1 |
Read the value displayed on the GTS.
Standard Value |
---|
Higher than 128°C (262°F) |
Tech Tips
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.
Result | |||
---|---|---|---|
|
OK |
REPLACE MASS AIR FLOW METER SUB-ASSEMBLY Click here |
NG |
CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connectors.
Measure the resistance according to the value(s) in the table below.
Standard Resistance | |||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Result | |||
---|---|---|---|
|
OK |
REPLACE ECM Click here |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
*1 | mass air flow meter sub-assembly |
*2 | ECM |
*a | Bank 1 |
*b | Bank 2 |
Disconnect the mass air flow meter sub-assembly connector.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / All Data / Intake Air Temp B1S1 or Intake Air Temp B2S1.
Tester Display |
---|
Intake Air Temp B1S1 |
Intake Air Temp B2S1 |
Read the value displayed on the GTS.
Standard Value |
---|
-40°C (-40°F) |
Tech Tips
Perform "Inspection After Repair" after replacing the mass air flow meter sub-assembly.
Result | |||
---|---|---|---|
|
OK |
REPLACE MASS AIR FLOW METER SUB-ASSEMBLY Click here |
NG |
CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM)
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance | |||||||||
---|---|---|---|---|---|---|---|---|---|
|
Result | |||
---|---|---|---|
|
OK |
REPLACE ECM Click here |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |