REAR DOOR REASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for both the RH and LH sides.

  • The procedure described below is for the RH side.

PROCEDURE


  1. INSTALL NO. 4 BLACK OUT TAPE (w/ No. 4 Black Out Tape)

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  2. INSTALL NO. 2 BLACK OUT TAPE

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  3. INSTALL REAR DOOR WEATHERSTRIP


    1. A004F6X

      Engage the 29 clips to install the rear door weatherstrip.

    2. Install the 2 clips.

  4. INSTALL REAR DOOR CHECK ASSEMBLY


    1. Apply MP grease to the sliding areas of the rear door check assembly.

    2. A004GD8C02
      *a Body Panel
      *b Door Panel

      Install the rear door check assembly onto the door panel with the 2 bolts.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
    3. Apply adhesive to the threads of the bolt.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
    4. Install the rear door check assembly onto the body panel with the bolt.

      Torque:
      30 N*m  { 306 kgf*cm, 22 ft.*lbf }
  5. INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY


    1. Apply MP grease to the sliding areas of the rear door outside handle frame sub-assembly.

    2. A004EX2C01
      *a Grommet

      Engage the grommet and 2 claws to install the rear door outside handle frame sub-assembly in the direction indicated by the arrow as shown in the illustration.

    3. A004FWV

      Using a T30 "TORX" socket wrench, tighten the screw.

      Torque:
      4.0 N*m  { 41 kgf*cm, 35 in.*lbf }
  6. INSTALL REAR DOOR OUTSIDE HANDLE REAR PAD


    1. A004GI1

      Engage the 2 claws to install the rear door outside handle rear pad.

  7. INSTALL REAR DOOR OUTSIDE HANDLE FRONT PAD


    1. A004FGU

      Engage the 3 claws to install the rear door outside handle front pad.

  8. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY


    1. A004E3F

      Pushing the rear door outside handle in the direction of the arrow mark shown in the illustration, install the rear door outside handle assembly.

  9. INSTALL REAR DOOR OUTSIDE HANDLE COVER


    1. A004E5H

      Engage the 2 claws to install the rear door outside handle cover.

    2. A004F9O

      Using a T30 "TORX" socket wrench, tighten the screw.

      Torque:
      4.0 N*m  { 41 kgf*cm, 35 in.*lbf }
  10. INSTALL REAR DOOR LOCK ASSEMBLY

    Click here

  11. INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  12. INSTALL REAR DOOR GLASS RUN


    1. A004EVF

      Engage the 2 guides and install the rear door glass run.

    2. Install the clip.

  13. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/ Power Window)


    1. Apply MP grease to the sliding parts of the rear door window regulator sub-assembly.

    2. Temporarily install the temporary bolt.

    3. A004E9XE06
      Text in Illustration
      *a Temporary Bolt

      Insert the rear door window regulator sub-assembly into the door panel. Use the temporary bolt to hang the rear door window regulator sub-assembly on the door panel.

    4. Tighten the 3 bolts and temporary bolt in the order shown in the illustration.

      Torque:
      9.5 N*m  { 97 kgf*cm, 84 in.*lbf }
    5. Connect the connector.

  14. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY (w/o Power Window)


    1. A004G40E05

      Install the rear door window regulator sub-assembly with the 3 bolts in the order shown in the illustration.

      Torque:
      9.5 N*m  { 97 kgf*cm, 84 in.*lbf }
  15. INSTALL REAR DOOR GLASS SUB-ASSEMBLY


    1. A004ECFE01

      Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as indicated by the arrows in the order shown in the illustration.

      Note

      Do not damage the rear door glass sub-assembly.

    2. A004ERC

      Slide the lower section of the rear door glass sub-assembly as indicated by the arrow as shown in the illustration.

  16. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


    1. A004E8W

      Engage the rear door window division bar sub-assembly to the rear door glass run.

    2. Install the rear door window division bar sub-assembly with the 3 bolts and nut.

      Torque:
      6.2 N*m  { 63 kgf*cm, 55 in.*lbf }
  17. INSTALL REAR DOOR SERVICE HOLE COVER


    1. Apply new butyl tape to the rear door panel.

    2. Pass the rear door lock remote control cable assembly, rear door inside locking cable assembly and each connector through a new rear door service hole cover.

    3. A004F1YE02
      Text in Illustration
      *a Reference Point

      Install a new rear door service hole cover according to the reference points on the rear door panel.

      Tech Tips

      Securely install the rear door service hole cover taking care to prevent wrinkles.

  18. INSTALL REAR SPEAKER ASSEMBLY (w/ Rear Speaker)

    Click here

  19. INSTALL REAR DOOR OUTSIDE MOULDING (w/ Outside Moulding)

    Tech Tips

    Use the same procedure as for the LH side.

    Click here

  20. INSTALL REAR DOOR GLASS INNER WEATHERSTRIP


    1. A004FG6

      Engage the 7 claws to install the rear door glass inner weatherstrip as shown in the illustration.

  21. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


    1. A004EE7

      Engage the 4 guides to install the rear door inside handle sub-assembly.

  22. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY


    1. A004E5ME03
      Text in Illustration
      *1 Rear Door Lock Remote Control Cable Assembly
      *2 Rear Door Inside Locking Cable Assembly

      Connect the rear door lock remote control cable assembly and the rear door inside locking cable assembly to the rear door inside handle.

    2. A004FJT

      Engage the 7 clips to install the rear door trim board sub-assembly.

    3. A004EKE

      Install the 3 screws.

    4. A004EIW

      Engage the claw and close the cover.

  23. INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/ Power Window)


    1. Connect the connector.

    2. A004EWC

      Engage the clip, 7 claws and 3 guides to install the rear door armrest base upper panel.

  24. INSTALL REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window)


    1. A004F2B

      Engage the 5 claws to install the rear door armrest base upper panel.

  25. INSTALL REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)


    1. Install the rear door window regulator handle assembly and fully open the rear door glass sub-assembly.

    2. Remove the rear door window regulator handle assembly.

    3. A004G8DE01
      Text in Illustration
      *a Inside of Vehicle

      Install the window regulator handle plate as shown in the illustration.

    4. A004G1AE01
      Text in Illustration
      *a Assemble with Glass in Fully Open Position

      Install the rear door window regulator handle assembly with the clip at the angle shown in the illustration.

  26. INSTALL REAR DOOR FRAME GARNISH


    1. A004G0Q

      Engage the guide.

    2. Engage the 2 clips and claw and install the rear door frame garnish.

  27. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (w/ Power Window)


    1. Connect the cable to negative auxiliary battery terminal.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    2. Install the front floor cover RH (for Front Floor Cover Type A).

      Click here

    3. Install the center front floor cover (for Front Floor Cover Type B).

      Click here

    4. Install the front floor cover RH (for Front Floor Cover Type B).

      Click here

  28. INSPECT POWER WINDOW OPERATION (w/ Power Window)

    Click here