PROCEDURE
INSTALL REAR NO. 2 SIDE RAIL SPACER LH
Attach the 2 claws to install the No. 2 side rail spacer.
INSTALL REAR NO. 2 SIDE RAIL SPACER RH
Tech Tips
Use the same procedure described for the LH side.
INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH
Attach the 5 claws to install the front shoulder belt anchor plate.
INSTALL FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH
Tech Tips
Use the same procedure described for the LH side.
INSTALL REAR DOOR SCUFF PLATE OUTSIDE LH
Attach the 2 clips to install the rear door scuff plate outside.
INSTALL REAR DOOR SCUFF PLATE OUTSIDE RH
Tech Tips
Use the same procedure described for the LH side.
INSTALL FRONT DOOR SCUFF PLATE OUTSIDE LH
Attach the 3 clips to install the front door scuff plate outside.
INSTALL FRONT DOOR SCUFF PLATE OUTSIDE RH
Tech Tips
Use the same procedure described for the LH side.
INSTALL ROOF HEADLINING ASSEMBLY
Place the roof headlining into the vehicle through the passenger door.
Note
Be careful not to damage the roof headlining when placing it in the cabin.
*A | for LHD |
*B | for RHD |
Attach the clip to install the roof headlining.
for LHD:
*A | LHD |
Connect the 2 roof wire connectors.
*A | LHD |
Connect the 2 clamps.
for RHD:
*A | RHD |
Connect the roof wire connector.
*A | RHD |
Connect the 2 clamps and connector.
Connect the 4 clamps to the front pillar LH.
w/ Digital Audio Broadcasting Antenna:
Attach the wire harness clamp and connect the connector to the rear pillar LH.
Install the antenna with the 2 bolts.
Connect the clamp to the rear pillar RH.
Connect the 3 connectors.
Connect the 3 clamps to the front pillar RH.
Connect the connector.
w/ Pre-crash Safety System:
*A | w/o Camera Heater | *B | w/ Camera Heater |
*1 | Pre-crash safety city sensor connector | *2 | Camera heater connector |
w/o Camera Heater:
Connect the pre-crash safety city sensor connector.
w/ Camera Heater:
Connect the pre-crash safety city sensor connector.
Connect the camera heater connector.
w/ Rain Sensor:
Connect the rain sensor connector.
w/ EC Mirror:
Connect the EC mirror connector.
INSTALL SUNSHADE TRIM HOLDER
*A | w/o Rear Sunshade |
*B | w/ Rear Sunshade |
*1 | Pin |
Position the pin as shown in the illustration and install the sunshade trim holder.
INSTALL ASSIST GRIP SUB-ASSEMBLY
Tech Tips
Use the same procedure for the other assist grip.
Assemble the assist grip as shown in the illustration.
Install the assist grip.
INSTALL REAR ASSIST GRIP ASSEMBLY LH
Assemble the rear assist grip as shown in the illustration.
Install the rear assist grip.
INSTALL REAR ASSIST GRIP ASSEMBLY RH
Tech Tips
Use the same procedure described for the LH side.
INSTALL VISOR HOLDER
Tech Tips
Use the same procedure to install the visor holder on the other side.
Attach the 2 claws.
Push in the visor holder as shown in the illustration.
INSTALL VISOR ASSEMBLY LH
When clip remains on vehicle:
Install the clip removed from the vehicle to the visor assembly LH.
Attach the 2 clips to install the visor assembly LH.
Attach the 4 claws to lock the 2 clips with the visor cover.
INSTALL VISOR ASSEMBLY RH
Tech Tips
Use the same procedure described for the LH side.
INSTALL PRE-CRASH SAFETY CITY COVER (w/ Pre-crash Safety System)
INSTALL NO. 2 PRE-CRASH SAFETY CITY COVER (w/ Pre-crash Safety System)
INSTALL RAIN SENSOR COVER (w/ Rain Sensor)
INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)
INSTALL NO. 1 ROOM LIGHT ASSEMBLY
Connect the connector.
Attach the 4 clips to install the No. 1 room light.
INSTALL MAP LIGHT ASSEMBLY
Connect the connector.
Attach the 4 clips to install the map light.
INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
Tech Tips
Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Install the lower instrument panel sub-assembly Click here.
INSTALL CONSOLE BOX ASSEMBLY
w/o Console Box Lid:
Remove the console box assembly Click here.
w/ Console Box Lid:
Remove the console box assembly Click here.
INSTALL UPPER INSTRUMENT PANEL SUB-ASSEMBLY
Tech Tips
Use the same procedure for RHD and LHD vehicles.
The procedure listed below the for LHD vehicles.
Install the upper instrument panel sub-assembly Click here.
INSTALL INNER ROOF SIDE GARNISH LH
*1 | Clip A |
Install 2 new clips labeled A to the inner roof side garnish.
Attach the 5 clips to install the inner roof side garnish.
INSTALL INNER ROOF SIDE GARNISH RH
Tech Tips
Use the same procedure described for the LH side.
INSTALL CENTER PILLAR GARNISH LH
Pass the front seat outer belt floor anchor through the center pillar garnish.
Attach the clip to install the center pillar garnish.
Install the 2 screws.
Install the front seat outer belt floor anchor with the bolt.
INSTALL CENTER PILLAR GARNISH RH
Tech Tips
Use the same procedure described for the LH side.
INSTALL LAP BELT OUTER ANCHOR COVER
Tech Tips
Use the same procedure for the other lap belt outer anchor cover.
Attach the 3 claws to install the lap belt outer anchor cover.
INSTALL LOWER CENTER PILLAR GARNISH LH
Attach the 2 claws and 3 clips to install the lower center pillar garnish.
INSTALL LOWER CENTER PILLAR GARNISH RH
Tech Tips
Use the same procedure described for the LH side.
INSTALL FRONT PILLAR GARNISH LH
w/ Curtain Shield Airbag:
Remove the protective cover.
Install a new front pillar garnish clip to the front pillar garnish.
Tech Tips
Install the front pillar garnish clip so that it faces as shown in the illustration.
*a | CORRECT | *b | INCORRECT |
Attach the 2 guides.
*1 | Front Pillar Garnish Clip |
Attach the 2 clips to install the front pillar garnish.
INSTALL FRONT PILLAR GARNISH RH
Tech Tips
Use the same procedure described for the LH side.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH
*1 | Paint Mark |
*2 | Mark Position |
Install the rear door opening trim weatherstrip as shown in the illustration.
INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH
Tech Tips
Use the same procedure described for the LH side.
INSTALL REAR DOOR SCUFF PLATE LH
Attach the clip and 6 claws to install the front door scuff plate.
INSTALL REAR DOOR SCUFF PLATE RH
Tech Tips
Use the same procedure described for the LH side.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
*1 | Paint Mark |
*2 | Mark Position |
Install the front door opening trim weatherstrip as shown in the illustration.
INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Tech Tips
Use the same procedure described for the LH side.
INSTALL COWL SIDE TRIM BOARD LH
Attach the clip, claw and guide to install the cowl side trim board.
INSTALL COWL SIDE TRIM BOARD RH
Tech Tips
Use the same procedure described for the LH side.
INSTALL FRONT DOOR SCUFF PLATE LH
Attach the 2 clips and 8 claws to install the front door scuff plate.
INSTALL FRONT DOOR SCUFF PLATE RH
Tech Tips
Use the same procedure described for the LH side.
INSTALL REAR SIDE SEATBACK ASSEMBLY LH
INSTALL REAR SIDE SEATBACK ASSEMBLY RH
Tech Tips
Use the same procedure described for the LH side.
INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY
INSTALL FRONT SEAT ASSEMBLY LH
for Manual Seat:
Install the front seat assembly Click here.
for Power Seat:
Install the front seat assembly Click here.
INSTALL FRONT SEAT ASSEMBLY RH
Tech Tips
Use the same procedure described for the LH side.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.