FRONT SEAT ASSEMBLY(for Manual Seat) REASSEMBLY

Info Added 2018-01-24

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

PROCEDURE


  1. INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side)

    Click here

  2. INSTALL REAR UPPER NO. 2 SEAT TRACK COVER


    1. B008BJO

      Attach the 3 claws to install the rear upper No. 2 seat track cover.

  3. INSTALL REAR UPPER SEAT TRACK COVER


    1. B008BK4

      Attach the 3 claws to install the rear upper seat track cover.

  4. INSTALL SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY

    B008BK1

    1. Attach the 8 hooks to install the separate type front seat cushion spring assembly to the front seat adjuster assembly LH.

    2. B008BJC

      for Front Passenger Side:

      Attach the 2 clamps to install the connector holder.

  5. INSTALL FRONT SEAT ADJUSTER ASSEMBLY LH


    1. B008BJ7

      Using a T50 "TORX" socket wrench, install the front seat adjuster assembly LH with the 4 "TORX" bolts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }
  6. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH (for Driver Side)

    B008BK9

    1. Attach the guide to install the front seat lower cushion shield LH with the screw.

  7. INSTALL FRONT SEAT WIRE LH (w/ Lumbar Support)


    1. B008BKQ

      Attach the claw to install the front seat wire LH.

    2. Connect the connector.

    3. Attach the 2 wire harness clamps.

    4. B008BM3

      Attach the 2 wire harness clamps to install the front seat wire LH.

  8. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (w/ Seat Heater System)


    1. B008BLV

      Attach the claw to install the seat climate control controller LH.

  9. INSTALL FRONT SEAT AIRBAG ASSEMBLY LH

    Click here

  10. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar Support)

    Click here

  11. INSTALL SEPARATE TYPE FRONT SEATBACK PAD


    1. B008BJS

      Install the separate type front seatback pad.

  12. INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)

    Click here

  13. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. Temporarily install the separate type front seatback cover.

    2. B008BJUE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 3 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    3. B008BKWE01
      Text in Illustration
      *1 Hog Ring Pliers

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 3 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    4. B008BKLE02
      Text in Illustration
      *1 Hog Ring Pliers
      *2 Hog Ring
      *3 Hook

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 2 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

    5. Attach the 2 hooks.

    6. B008BMLE02
      Text in Illustration
      *1 Hog Ring Pliers
      *2 Strap

      Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 5 new hog rings.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

      • When installing the separate type front seatback cover, make sure to pass the straps of the separate type front seatback cover through the hog rings.

    7. B008BJY

      Attach the 2 claws to install the 2 front seat headrest supports.

    8. B008BLY

      Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

    9. B008BJW

      Attach the 2 hooks.

    10. B008BLT

      Attach the 2 hooks to connect the 2 straps.

    11. B008BL1

      Attach the hook at the bottom of the separate type front seatback cover.

    12. B008BL8

      Attach the 2 hooks.

  14. INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

    Tech Tips

    Perform this procedure when it is necessary to remove and reinstall or replace the separate type front seatback assembly.


    1. B008BM7

      Using a T50 "TORX" socket wrench, install the separate type front seatback assembly to the front seat adjuster assembly LH with the 4 "TORX" bolts.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }
    2. w/ Lumbar Support:


      1. B008BLJ

        Attach the 2 wire harness clamps.

      2. Connect the connector.

      3. B008BLY

        Pass the 2 straps through the 2 holes of the separate type front seatback pad to the backside.

      4. B008BJW

        Attach the 2 hooks.

      5. B008BLT

        Attach the 2 hooks to connect the 2 straps.

      6. B008BL1

        Attach the hook at the bottom of the separate type front seatback cover.

    3. B008BL8

      Attach the 2 hooks.

    4. B008BJQ

      Attach the claw and connect the connector.

    5. Attach the 2 wire harness clamps.

  15. INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)

    Click here

  16. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. B008BIG

      Attach the 13 hooks to install the separate type front seat cushion cover to the separate type front seat cushion pad.

      Note


      • Be careful not to damage the separate type front seat cushion cover.

      • When attaching the hooks, avoid wrinkling the separate type front seat cushion cover.

  17. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD


    1. Attach the 9 hooks to install the separate type front seat cushion cover with pad.

      B008BIH
    2. B008BKR

      w/ Lumbar Support:

      Attach the wire harness clamp.

    3. B008BIO

      for Front Passenger Side:

      Attach the claw to connect the connector.

    4. w/ Seat Heater System:


      1. B008BLD

        Connect the connector.

      2. B008BJK

        Attach the claw to connect the connector.

      3. Attach the wire harness clamp.

      4. for Type A:

        Connect the 2 connectors.

      5. B008BMD

        for Type B:

        Connect the connector.

    5. B008BIU

      Attach the 2 hooks.

  18. INSTALL FRONT OUTER SEAT CUSHION BRACKET (for Driver Side)


    1. B008BIN

      Attach the 4 claws to install the front seat hinge pin and front outer seat cushion bracket to the connector link.

    2. B008BLH

      Attach the 2 claws to install the vertical adjuster handle bracket with connector link.

    3. B008BLOE01
      Text in Illustration
      *1 Connector Link

      Connect the connector link and install the clip.

  19. INSTALL RECLINING CONTROL LEVER LH


    1. Temporarily install the reclining control lever LH with the 2 nuts.

    2. B008BLWE02
      Text in Illustration
      *1 Nut A
      *2 Nut B

      Using a 15 mm socket wrench, tighten nut B.

      Torque:
      for Nut B
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }
    3. Tighten nut A.

      Torque:
      for Nut A
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }
    4. B008BJM

      Attach the 2 hooks to install the spring.

  20. INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. B008BM4

      Attach the hook to install the front seat inner cushion shield LH with the screw.

  21. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)

    Click here

  22. INSTALL FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)

    Click here

  23. INSTALL SEAT SLIDE POSITION SENSOR PROTECTOR (for Driver Side)


    1. B008BK6

      Attach the 2 clamps and connect the wire harness.

    2. B008BKT

      Attach the 2 claws and 2 guides to install the seat slide position sensor protector with the screw.

  24. INSTALL LUMBAR FRONT POWER SEAT SWITCH (w/ Lumbar Support)

    Click here

  25. INSTALL FRONT SEAT CUSHION SHIELD LH


    1. B008BIJ

      w/ Lumbar Support:

      Connect the connector.

    2. B008BMM

      Attach the claw and hook to install the front seat cushion shield LH.

    3. Install the 2 screws.

    4. B008BMJ

      Attach the 2 rubber bands.

  26. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    1. B008BLU

      Attach the claw to install the reclining adjuster release handle LH.

  27. INSTALL VERTICAL ADJUSTING HANDLE LH (for Driver Side)


    1. B008BLS

      Install the vertical adjusting handle LH with the 2 screws.

  28. INSTALL VERTICAL SEAT ADJUSTER KNOB CAP (for Driver Side)


    1. B008BJD

      Attach the 3 claws to install the vertical seat adjuster knob cap.