DESCRIPTION
When the entry operation and wireless operation door lock functions do not operate, a malfunction or wave interference may be occurring in either of the following: 1) the signal communication line between the door control receiver and certification ECU (the line is used by entry and wireless); or 2) the electrical key transmitter.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
Note
The entry and start system (for entry function) uses a multiplex communication system (LIN communication system) and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the entry and start system (for entry function) after confirming that the communication system is functioning properly.
When using the intelligent tester with the engine switch off to troubleshoot: Connect the intelligent tester to the DLC3, and turn a courtesy light switch on and off at 1.5-second intervals until communication between the tester and vehicle begins.
Check that there are no electrical key transmitters in the vehicle.
Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output Click here.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations according to the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.
PROCEDURE
CHECK POWER DOOR LOCK CONTROL SYSTEM
When the master switch door control switch is operated, check that the locked doors unlock Click here.
OK |
---|
Locked doors unlock. |
NG |
GO TO POWER DOOR LOCK CONTROL SYSTEM Click here |
OK |
CHECK ELECTRICAL KEY TRANSMITTER
When another registered electrical key transmitter is used, check that the wireless and entry functions operate normally Click here.
Result | Proceed to |
---|---|
Entry function operates and electrical key transmitter that did not operate is electrical key transmitter | A |
Entry function does not operate | B |
B |
CHECK WAVE ENVIRONMENT Click here |
A |
CHECK ELECTRICAL KEY TRANSMITTER (LED)
Check that the transmitter LED illuminates 3 times when a switch is pressed 3 times.
Result | Proceed to |
---|---|
Transmitter LED does not illuminate when switch is pressed 3 times | A |
Transmitter LED illuminates 3 times when switch is pressed 3 times | B |
Transmitter LED does not illuminate second or third time | C |
Tech Tips
If the transmitter LED does not illuminate the second or third time, replace the transmitter battery as it is depleted.
B |
REPLACE ELECTRICAL KEY TRANSMITTER |
C |
REPLACE TRANSMITTER BATTERY Click here |
A |
INSPECT TRANSMITTER BATTERY (VOLTAGE)
Remove the battery from the electrical key transmitter that does not operate. Attach a lead wire (0.6 mm (0.0236 in.) or less in diameter including wire sheath) with tape or equivalent to the negative terminal Click here.
Note
Do not wrap the lead wire around a terminal, wedge it between terminals, or solder it. A terminal may be deformed or damaged, and the battery will not be able to be installed correctly.
Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.
*1 | Measurement Position |
Using an oscilloscope, check the transmitter battery voltage waveform.
Tech Tips
When measuring the battery voltage, while operating the lock switch of a door handle, bring the electrical key transmitter within the entry operating range to perform the measurement. For the entry operating range, refer to System Description Click here.
OK | ||||||||
---|---|---|---|---|---|---|---|---|
|
OK |
REPLACE ELECTRICAL KEY TRANSMITTER |
NG |
REPLACE TRANSMITTER BATTERY Click here |
CHECK WAVE ENVIRONMENT
Bring the electrical key transmitter near the door control receiver and perform a wireless and entry function operation check.
Tech Tips
When the electrical key transmitter is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.
OK |
---|
Wireless and entry functions operate normally. |
OK |
AFFECTED BY WAVE INTERFERENCE |
NG |
CHECK POWER SOURCE
Check that the combination meter display turns off when the engine switch is turned off.
OK |
---|
Combination meter turns off. |
Tech Tips
This confirms that systems other than the entry and start system are correctly detecting the state of the power source.
NG |
GO TO ENTRY AND START SYSTEM (FOR START FUNCTION) |
OK |
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - BATTERY AND BODY GROUND)
*1 | Front view of wire harness connector (to Certification ECU) |
Disconnect the D54 ECU connector.
Measure the voltage according to the value(s) in the table below.
Standard Voltage | |||||||||
---|---|---|---|---|---|---|---|---|---|
|
Measure the resistance according to the value(s) in the table below.
Standard Resistance | ||||||
---|---|---|---|---|---|---|
|
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
OK |
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR CONTROL RECEIVER AND BODY GROUND)
*1 | Front view of wire harness connector (to Certification ECU) |
*2 | Front view of wire harness connector (to Door Control Receiver) |
Disconnect the D59 ECU connector.
Disconnect the H24 receiver connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance | ||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
OK |
CHECK DOOR CONTROL RECEIVER (OPERATION)
for Wagon:
Temporarily replace the door control receiver with a new or normally functioning one Click here.
for Sedan:
Temporarily replace the door control receiver with a new or normally functioning one Click here.
Check that the wireless and entry functions operate normally.
OK |
---|
Wireless and entry functions operate normally. |
OK |
END (DOOR CONTROL RECEIVER IS DEFECTIVE) |
NG |
REPLACE CERTIFICATION ECU |