Info Added 2017-10-06
CAUTION / NOTICE / HINT
Tech Tips
Use the same procedure for LHD and RHD vehicles.
The procedure listed below is for the LHD vehicles.
PROCEDURE
INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
Engage the guides to install the instrument panel safety pad sub-assembly as shown in the illustration.
Install in this Direction (1) | Install in this Direction (2) |
Engage each clamp.
Connect each connector.
Connect the airbag connector.
*a | Airbag Connector | *b | Airbag Bolt |
*c | Ground Bolt A | *d | Ground Bolt B |
Install the 4 clips.
Install the 10 bolts as shown in the illustration.
INSTALL NO. 2 HEATER TO REGISTER DUCT SUB-ASSEMBLY
Install in this Direction |
Engage the claws to install the No. 2 heater to register duct sub-assembly as shown in the illustration.
INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (w/ Display)
*a | Runner Portion |
*b | Cut Off |
When installing a new No. 1 instrument panel garnish sub-assembly:
Using a nipper, cut off both ends of the runner portion as shown in the illustration.
Install in this Direction |
Engage the clips and guides to install the No. 1 instrument panel garnish sub-assembly as shown in the illustration.
Install the 2 bolts <G>.
INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)
INSTALL INSTRUMENT PANEL CENTER REGISTER ASSEMBLY
Install in this Direction |
Engage the guides and claws to install the instrument panel center register assembly as shown in the illustration.
Install the 2 screws <D>.
INSTALL NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY (w/o Display)
*a | Runner Portion |
*b | Cut Off |
When installing a new No. 1 instrument panel garnish sub-assembly:
Using a nipper, cut off both ends of the runner portion as shown in the illustration.
Install in this Direction |
Engage the guides and clips to install the No. 1 instrument panel garnish sub-assembly as shown in the illustration.
INSTALL STARTER SWITCH BEZEL (for LHD with Entry and Start System)
Connect the connector.
Install in this Direction |
Engage the clips to install the starter switch bezel as shown in the illustration.
INSTALL INSTRUMENT CLUSTER FINISH LOWER CENTER PANEL SUB-ASSEMBLY
Connect the connector.
Install in this Direction |
Engage the clips to install the instrument cluster finish lower center panel sub-assembly as shown in the illustration.
INSTALL NO. 1 RADIO BRACKET (w/o Cover)
Engage the guides to install the No. 1 radio bracket.
Install the 2 bolts <G>.
INSTALL NO. 2 RADIO BRACKET (w/o Cover)
Engage the guides to install the No. 2 radio bracket.
Install the 2 bolts <G>.
INSTALL NO. 1 RADIO BRACKET (w/ Cover)
Engage the guides to install the No. 1 radio bracket.
Install the 3 screws <D>.
INSTALL NO. 2 RADIO BRACKET (w/ Cover)
Engage the guides to install the No. 2 radio bracket.
Install the 3 screws <D>.
INSTALL STEREO OPENING COVER WITH BRACKET (w/ Cover)
Connect the connector.
Engage the guides to install the stereo opening cover with bracket.
Install the 4 bolts <G>.
INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio Receiver Type)
INSTALL INSTRUMENT CLUSTER FINISH CENTER PANEL SUB-ASSEMBLY (w/o Display)
Install in this Direction |
Engage the claws to install the instrument cluster finish center panel sub-assembly as shown in the illustration.
INSTALL INSTRUMENT PANEL LOWER FINISH PANEL SUB-ASSEMBLY (w/o Knee Airbag)
Engage the clips to install the instrument panel lower finish panel sub-assembly to the fuse box opening cover.
Install the 2 screws <D>.
INSTALL FUSE BOX OPENING COVER (w/o Knee Airbag)
Connect each connector.
Install in this Direction |
Engage the clips and claws to install the fuse box opening cover with instrument panel lower finish panel sub-assembly as shown in the illustration.
Install the screw <D>.
INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY WITH DOOR (w/ Knee Airbag)
INSTALL FUSE BOX OPENING COVER (w/ Knee Airbag)
Connect each connector.
Install in this Direction |
Engage the clips to install the fuse box opening cover as shown in the illustration.
Install the screw <D>.
CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Install in this Direction |
Engage the guides and claw to connect the hood lock control lever sub-assembly as shown in the illustration.
INSTALL COMBINATION METER ASSEMBLY
INSTALL STARTER SWITCH BEZEL (for RHD with Entry and Start System)
Connect the connector.
Install in this Direction |
Engage the clips to install the starter switch bezel as shown in the illustration.
INSTALL NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
Install in this Direction |
Engage the clips to install the No. 2 instrument panel garnish sub-assembly as shown in the illustration.
INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Install in this Direction |
Engage the guides and clips to install the instrument cluster finish panel assembly as shown in the illustration.
Install the 2 clips.
Install in this Direction |
Engage the claws to install the meter hood spacer as shown in the illustration.
INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
w/ Switch:
Connect each connector.
Install in this Direction |
Engage the clips to install the instrument cluster finish panel sub-assembly as shown in the illustration.
INSTALL NO. 2 FRONT SPEAKER ASSEMBLY (w/ Woofer)
INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
w/ Speaker:
Connect the connector.
Install in this Direction (1) | |
Install in this Direction (2) |
Engage the guides, claws and clips to install the No. 1 instrument panel speaker panel sub-assembly as shown in the illustration.
INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
Tech Tips
Use the same procedure as for the No. 1 instrument panel speaker panel sub-assembly side.
INSTALL FRONT PILLAR GARNISH LH
*a | Protective Cover |
Adhesive Tape |
Remove the adhesive tape and protective cover.
Install the 2 front pillar garnish clips to the front pillar garnish LH.
Note
If the front pillar garnish clip has significant damage, replace it with a new one.
When installing the front pillar garnish clip, make sure to install it in the correct position and facing in the correct direction.
w/ Speaker:
Connect the connector.
Install in this Direction |
Engage the guides as shown in the illustration.
Install in this Direction |
Engage the clips to install the front pillar garnish LH as shown in the illustration.
INSTALL FRONT PILLAR GARNISH RH
Tech Tips
Use the same procedure as for the LH side.
INSTALL INSTRUMENT SIDE PANEL LH
Install in this Direction (1) | |
Install in this Direction (2) |
Engage the guides and clips to install the instrument side panel LH as shown in the illustration.
w/ Airbag Cut Off Switch:
Connect the connector.
INSTALL INSTRUMENT SIDE PANEL RH
Tech Tips
Use the same procedure as for the LH side.
INSTALL INSTRUMENT PANEL FINISH END PANEL LH
Install in this Direction (1) | |
Install in this Direction (2) |
Engage the guides and clips to install the instrument panel finish end panel LH as shown in the illustration.
INSTALL INSTRUMENT PANEL FINISH END PANEL RH
Tech Tips
Use the same procedure as for the LH side.
CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Connect the front door opening trim weatherstrip LH to the area shown in the illustration.
CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Tech Tips
Use the same procedure as for the LH side.
INSTALL NO. 2 INSTRUMENT PANEL LOWER FINISH PANEL
Connect the connector.
Install in this Direction |
Engage the clips and claws to install the No. 2 instrument panel lower finish panel as shown in the illustration.
Install the 5 screws <D>.
INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY
Engage the claw to install the glove compartment door stopper sub-assembly.
INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
Install in this Direction |
With the glove compartment door assembly opened approximately 61° from its closed position, engage the 4 hinges horizontally.
Note
Engaging the hinges from the top will deform the hinges.
Be sure to install the glove compartment door assembly horizontally.
*a | Stopper |
While pushing in the sides of the glove compartment door assembly as indicated by the arrows in the illustration, close the door to engage it to the 2 stoppers.
Engage the claw to connect the glove compartment door stopper sub-assembly.
INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Install in this Direction (1) | |
Install in this Direction (2) |
Engage the guides and claws to install the No. 2 instrument panel under cover sub-assembly as shown in the illustration.
INSTALL COWL SIDE TRIM BOARD RH
INSTALL FRONT DOOR SCUFF PLATE RH
INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY
INSTALL REAR CONSOLE BOX ASSEMBLY
CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
INSPECT SRS WARNING LIGHT