NAVIGATION SYSTEM OPERATION CHECK


  1. CHECK NAVIGATION SYSTEM NORMAL CONDITION


    1. If the symptom is applicable to any of the following, it is intended behavior, and not a malfunction.

      Symptom Answer
      A longer route than expected is chosen. Depending on the road conditions, the radio receiver assembly may determine that a longer route is quicker.
      Even when distance priority is high, the shortest route is not shown. Some routes may not be advised due to safety concerns.
      When the vehicle is put into motion immediately after the engine starts, the navigation system deviates from the correct position. If the vehicle starts before the navigation system activates, the system may not react.
      When driving on certain types of roads, especially new roads, the vehicle position deviates from the correct position. When the vehicle is driving on new roads not available on the SD card (disc player disc), the system attempts to match it to another nearby road, causing the position mark to deviate.
      Expected arrival time is earlier than current time, or time different from expected arrival time is displayed. If a destination is set to a point where a different time zone is used, the system displays an expected arrival time corresponding to the time zone of the destination. If a location on the sea is set as the destination, the system may display an expected arrival time corresponding to the time zone setting of the vehicle. Check which communication is not used for displaying traffic information.
    2. B00740V

      The following symptoms are not malfunctions, but are caused by errors inherent in the GPS, gyro sensor or radio receiver assembly.


      1. The current position mark may be displayed on a nearby parallel road.

      2. B0076R9

        Immediately after a fork in the road, the current vehicle position mark may be displayed on the wrong road.

      3. B0074YH

        When the vehicle turns right or left at an intersection, the current vehicle position mark may be displayed on a nearby parallel road.

      4. B00766E

        When the vehicle is carried, such as on a ferry, and the vehicle itself is not driving, the current vehicle position mark may be displayed in the position where the vehicle was until a measurement can be performed by the GPS.

      5. B0073WP

        When the vehicle travels on a steep hill, the current vehicle position mark may deviate from the correct position.

      6. B0072PI

        When the vehicle makes a continuous turn (e.g. 360, 720, 1080 degrees), the current vehicle position mark may deviate from the correct position.

      7. B0073I6

        When the vehicle moves erratically, such as constant lane changes, the current vehicle position mark may deviate from the correct position.

      8. B00739H

        When the engine switch is turned on (ACC) or on (IG) and the vehicle is turned on a turntable before parking, the current vehicle position mark may not indicate the correct direction. The same will occur when the vehicle comes out of the parking garage.

      9. B00735F

        When the vehicle travels on a snowy road or a mountain path with tire chains installed or using a spare tire, the current vehicle position mark may deviate from the correct position.

      10. B0072MF

        When the tires are changed, the current vehicle position mark may deviate from the correct position.

        Tech Tips


        • A change in tire diameter may cause a speed sensor error.

        • Performing "tire change" in calibration mode will allow the system to correct the current vehicle position faster.

  2. REMOTE TOUCH SELF CHECK

    Note


    • Before entering self-diagnostic mode, make sure there are no obstructions which may interfere with operation of the touchpad, and that the touchpad is not dirty.

    • Do not touch the touchpad except when necessary.

    • Since the touchpad may recognize a pinch in/out or flick operation if operated with 2 fingers, always use 1 finger to operate the touchpad in self-diagnostic mode.

    Tech Tips

    The following checks can be done via self-diagnostic mode:


    • Remote touch DTC check

    • Switch illumination check

    • Touch screen operation position recognition condition check

    • Switch operation check

    • Vibration feedback generation condition check


    1. B0073AOC02
      *A for RHD
      *B for LHD
      *a Home Switch
      *b Touchpad Frame

      Activate Self-diagnostic Mode


      1. Turn the light control switch to the tail or head position.

      2. While touching the frame of the touchpad and pressing and holding the home switch, turn the engine switch on (ACC) to enter self-diagnostic mode.

        Note

        If the frame of the touchpad is not being touched when the engine switch is turned on (ACC), self-diagnostic mode will not be entered.

    2. Switch Illumination Check and DTC Check


      1. B0073DEC03
        *a Switch Illumination

        Check that the switch illumination turns on.

        Tech Tips

        If present DTCs are stored during self-diagnostic mode, the switch illumination will blink at 0.5-second intervals. The switch illumination will continue to blink until self-diagnostic mode is ended.

    3. B007543C02
      *a Lateral Axis
      *b Longitudinal Axis

      Touchpad operation position recognition condition check


      1. Operate the touchpad laterally and longitudinally and check that the brightness of the switch illumination changes.

        Tech Tips


        • If the brightness of the switch illumination changes according to the position touched on the touchpad, the touchpad operation position is correctly being recognized.

        • The brightness of the switch illumination changes between 0% and 100% according to the touchpad operation coordinates.

        • The touchpad operation coordinates change between 0 and 255 for the lateral axis and between 1 and 255 for the longitudinal axis.

        • When the touchpad operation coordinates are 0 for the lateral axis and 1 for the longitudinal axis, the brightness of the switch illumination will be 0% (off). When the coordinates of both the lateral and longitudinal axis are 255, the brightness of the switch illumination will be 100% (full brightness).

    4. Switch Operation Check


      1. Check that the switch illumination turns on at 100% brightness when each switch is pressed while touching the lower left of the touchpad.

        Tech Tips

        If the switch illumination turns on at 100% brightness when a switch is pressed, the switch being pressed is operating normally.

    5. Vibration feedback generation condition check


      1. B0076QFC03
        *a Feedback Force Image Screen
        *b Button

        Operate the touchpad to move the pointer displayed on the multi-display assembly screen and check that remote touch (remote operation controller assembly) generates vibration feedback according to the pointer display position on the multi-display assembly.

        Tech Tips


        • On the multi-display assembly customize setting screen, if the feedback force setting is set to "LEVEL1 (No Vibration)", no vibration feedback will be generated.

        • If the remote touch (remote operation controller assembly) generates vibration feedback according to the pointer display position, the remote touch (remote operation controller assembly) is correctly receiving the reaction force setting signal sent from the radio receiver assembly.

        • If the remote touch (remote operation controller assembly) cannot receive the reaction force setting signal sent from the radio receiver assembly, use the default feedback force image stored in the remote touch to generate vibration feedback on the touchpad.

    6. End Self-diagnostic Mode


      1. Do not perform any operations for 30 seconds, or turn the engine switch off to end self-diagnostic mode.

  3. CHECK SD CARD (DISC PLAYER DISC)

    Tech Tips


    • Check the SD card (disc player disc) installed in the radio receiver assembly.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B0073ZQ

      Select "Failure Diagnosis" from the "Service Menu" screen.

    3. A01VS2K

      Select "SD Check" from the "Failure Diagnosis" screen.

    4. B00764JC01
      *a Result

      SD Check


      1. Select "SD Check" to start the SD card (disc player disc) check.

      2. Check the result displayed when the SD check is complete.

        Screen Description
        Display (Result) Description
        Checking Check is in progress
        OK SD card (disc player disc) is normal
        NG SD card (disc player disc) is malfunctioning

        Tech Tips


        • After selecting "SD Check", it may take a while until the result is displayed.

        • If the cabin temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher, the SD card (disc player disc) may not operate normally, and "NG" may be shown on the display. Make sure to perform the inspection with the cabin at an appropriate temperature.

        • If "NG" is displayed even when the cabin temperature is appropriate, replace the SD card (disc player disc) with a new or known good one.

  4. CHECK TELEMATICS TRANSCEIVER (w/ Telematics Transceiver for G-BOOK)

    Tech Tips


    • Communication between the telematics transceiver and G-BOOK center is checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B0073ZQ

      Select "Failure Diagnosis" from the "Service Menu" screen.

    3. A01VSWJ

      Select "DCM Check" from the "Failure Diagnosis" screen.

    4. B0077HEC01
      *a Result

      Telematics transceiver check


      1. Select "DCM Check" to start the telematics transceiver communication condition check.

      2. Check the result displayed when the DCM check is complete.

        Screen Description
        Result Description
        wait While the check is in progress
        OK Telematics transceiver communication condition is normal
        NO ANT Telephone antenna is not connected
        PLL NG PLL is unlocked
        OFF LINE Service contract is not valid
        No Service Out of communication service area
        RESTRICTION Restriction of outgoing signal
        NO CARRIER RLP link is not established
        ERROR High priority service is activated
        TIME OUT Check time out

        Tech Tips


        • Telematics transceiver check is performed for a maximum of 40 seconds after "DCM Check" is selected.

        • Check the telematics system when "DCM Check" cannot be performed or the check result is not "OK".

          Click here

  5. CHECK HARD DISK DRIVE (w/ Sound Library Function)

    Tech Tips


    • Check the hard disk drive (HDD) built into the radio receiver assembly.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B0073ZQ

      Select "Failure Diagnosis" from the "Service Menu" screen.

    3. A01VSGE

      Select "HDD Check" from the "Failure Diagnosis" screen.

    4. B0077FKC01
      *a Result

      HDD Check


      1. Select "HDD Check" to start the HDD check.

      2. Check the result displayed when the HDD check is complete.

        Screen Description
        Display (Result) Description
        Checking Check is in progress
        OK Hard disk drive is normal
        NG Hard disk drive is malfunctioning

        Tech Tips


        • After selecting "HDD Check", it may take a while until the result is displayed.

        • If the cabin temperature is -20°C (-4°F) or lower, or 65°C (149°F) or higher, the HDD may not operate normally, and "NG" may be shown on the display. Make sure to perform the inspection with the cabin at an appropriate temperature.

        • If "NG" is displayed even when the cabin temperature is appropriate, replace the HDD with a new one.

          Click here

  6. CHECK PANEL & STEERING SWITCH

    Tech Tips


    • The radio receiver assembly panel switches and steering switches are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B0077IW

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A01VR8Z

      Select "Panel & Steering Switch" from the "Function Check/Setting I" screen.

    4. B0076XXN04

      Panel & Steering Switch Check Mode

      Screen Description
      Display Content
      *a: Switch condition "Pushed" is displayed when any switch is pushed
      *b: Number of switches pushed
      • Number of switches pushed at once is displayed

      • If 3 switches are pushed at once, "3" or "More than 3" is displayed

      • If 4 or more switches are pushed at once, "More than 3" is displayed

      *c: Rotary switch direction Direction of rotary switch is displayed

      1. Operate each switch and check that the switch conditions are correctly displayed.

        Note

        If the "HOME" switch of the remote touch (remote operation controller assembly) is pressed and held for 3 seconds or more, diagnostic mode will be canceled.

  7. CHECK REMOTE TOUCH SWITCH

    Tech Tips


    • The touchpad is checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B0077IW

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A01VSLR

      Select "Remote Touch Switch" from the "Function Check/Setting I" screen.

    4. B0075IWN01

      Remote Touch Switch Check

      Screen Description
      Display Content
      *a: Pointer Displays the location of the pointer.
      *b: Coordinate
      • Displays the coordinates of the pointer

      • "X" and "Y" indicate the lateral and longitudinal axes

      • Coordinates are displayed by a number between 0 and 255 for lateral axis "X" and a number between 1 and 255 for longitudinal axis "Y" starting from the lower left of the screen

      *c: "+" mark Displayed at the location where the pointer was located when the touchpad was pressed or double tapped.

      1. While "Remote Touch Switch Check" is displayed, move the pointer to any blank area on the screen, and then press or double tap the touchpad.

        Tech Tips


        • The "+" mark is displayed at the pointer position when the touchpad is pressed or double tapped.

        • Even if the pointer is moved, the "+" mark will remain at the position where the pointer was when the touchpad was pressed or double tapped.

      2. Operate the touchpad to move the pointer. When the location of the pointer is changed by operating the touchpad, check that the coordinate value "X" changes between 0 and 255 and coordinate value "Y" changes between 1 and 255.

  8. CHECK MICROPHONE

    Tech Tips


    • The microphone and microphone input level are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B0077IW

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A01VSJR

      Select "Microphone Check" from the "Function Check/Setting I" screen.

    4. B0076G1N01

      Microphone Check

      Screen Description
      Display Content
      *a: Microphone input level meter Monitors the microphone input level every 0.1 seconds and displays the results in 8 different levels.
      *b: Recording switch Starts recording.
      *c: Stop switch Stops recording and playing.
      *d: Play switch Plays the recorded voice.
      *e: Recording indicator Comes on while recording.

      1. When speaking into the microphone, check that the microphone input level meter changes according to the input level.

        Tech Tips

        The microphone is active at all times when this screen is displayed.

      2. Push the recording switch and perform voice recording.

        Tech Tips


        • Select the recording switch with the blower motor of the air conditioning system stopped. If an outlet of the air conditioning system is facing the microphone, noise may be recorded.

        • While recording or playing, switches other than the stop switch cannot be pushed.

        • When no recording is present, the play switch cannot be pushed.

        • Recording will stop after 5 seconds or when the stop switch is pushed.

      3. Check that the recording indicator remains on while recording and that the recording can be played normally.

  9. CHECK GPS AND VEHICLE SENSORS

    Tech Tips


    • GPS information, vehicle signals and sensor signals are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B0077IW

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A01VSYH

      Select "System Sensors Check" from the "Function Check/Setting I" screen.

    4. B0072PGN01

      System Sensors Check

      *a: GPS
      Display Content
      Reception number Displays reception condition of the satellites used to determine vehicle position Blue: P (In use) System is using GPS signal for location.
      Yellow: T (Receiving) System is tracking GPS signal for location.
      No color: Not in use System cannot receive GPS signal (searching for GPS signal).
      Status Displays reception status of the satellites used to determine vehicle position OK (H3D) High accuracy 3-dimensional location method is being used.
      OK (H2D) High accuracy 2-dimensional location method is being used.
      OK (3D) 3-dimensional location method is being used.
      OK (2D) 2-dimensional location method is being used.
      NG Location data cannot be used.
      error Reception error has occurred.
      - Any other state.
      Measurement ratio Displays the ratio of satellites performing measurements 3D The ratio of satellites performing 3D positioning, Hyper 3D positioning and Hyper 2D positioning is displayed.
      2D The ratio of satellites performing 2D positioning is displayed.
      NG The ratio of satellites not performing measurement is displayed.
      Date Date/time information obtained from GPS signals is displayed in Greenwich Mean Time (GMT).
      Position Latitude and longitude information on current position is displayed.
      *b: SPD
      Display Content
      Pulse Count Displays the accumulated number of input pulses beginning when this screen is displayed
      Speed Displays vehicle speed (km/h)
      *c: Sensor Signal
      Display Content Note
      Gyro Voltage Displays the output voltage of the gyro sensor -
      0 point Voltage Displays the zero-point voltage of the gyro sensor -
      Relative bearing Displays the output angle of the gyro sensor The amount of change in bearing angle (degrees) after the system sensor check screen is displayed (clockwise: "+", counterclockwise: "-").
      *d: Reset
      Display Content
      Reset When this switch is pressed and held for 3 seconds or more, the values for the display items of SPD and Sensor Signal are reset and display "0".
      *e: Gyro/Distance correction study situation
      Display Content
      Gyro/Distance correction study situation Displays learning status of Gyro/Distance correction

      1. When the "System Sensors Check" screen is displayed, check all the sensor signals.

        Tech Tips

        This screen is updated once per second.

    5. B0075RBN02

      GPS Time Setting

      Screen Description
      Display Content
      *a: Time display Displays the date and time in the device.
      *b: Time setting screen Setting is possible only when GPS signals are not being received.
      *c: Cursor movement switch Moves the cursor on the date and time setting screen to the right and left.
      *d: Adjustment switch Adjusts values of items selected by the cursor.
      *e: OK switch Selecting this switch after setting the date and time updates the date and time in the device (only when GPS signals are not received).

      1. When GPS signals are not being received, the date and time in the device can be adjusted.

        Tech Tips

        Time setting is possible only when GPS signals are not being received. When the navigation system is receiving GPS signals, priority is given to displaying the time and date received via GPS.

  10. CHECK VEHICLE SIGNAL

    Tech Tips


    • Vehicle signals received by the radio receiver assembly are checked in the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B0077IW

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A01VSSP

      Select "Vehicle Signal" from the "Function Check/Setting I" screen.

    4. B0076H6

      Vehicle Signal Check Mode

      Screen Description
      Display Content
      Battery Battery voltage is displayed.
      IG Engine switch ON/OFF state is displayed.
      PKB Parking brake ON/OFF state is displayed.
      REV

      Reverse signal OFF state is displayed.

      When reverse signal is ON, this screen is not available. Using GTS, check reverse signal state on Data List.

      Click here

      SPEED Vehicle speed is displayed in km/h.
      TAIL Tail signal (light control switch) ON/OFF state is displayed.
      ADIM/TCAN Brightness state DIM (with)/BRIGHT (without) is displayed.

      Tech Tips


      • Only items sending vehicle signals will be displayed.

      • This screen displays vehicle signals input to the radio receiver assembly.

      • This screen is updated once per second.


      1. When the "Vehicle Signal Check Mode" screen is displayed, check all the vehicle signal conditions.

  11. CHECK SOUND LIBRARY SETTING (w/ Sound Library Function)

    Tech Tips


    • It is possible to check the sound library information and turn the sound library function on and off.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B0077IW

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A01VRWD

      Select "Sound Library Setting" from the "Function Check/Setting I" screen.

    4. B0076TZN02

      Sound Library Information

      Screen Description
      Display Content
      *a: Recording function setting for HDD Recording to HDD permitted (ON)/not permitted (OFF)
      *b: Number of albums Number of albums recorded on HDD
      *c: Number of tracks Number of tracks recorded on HDD
      *d: Free space in HDD Free space on HDD partition for sound library
  12. CHECK HANDS-FREE VOICE QUALITY SETTING

    Tech Tips


    • The hands-free volume of a "Bluetooth" compatible phone can be adjusted using the following procedure.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B0077IW

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A01VSX7

      Select "HF Voice Quality Setting" from the "Function Check/Setting I" screen.

    4. B0073XIC01
      *a Numeric Keypad
      *b Setting Button
      *c Reset Button

      Hands-Free Voice Quality Setting


      1. If necessary, refer to the table below to adjust the voice quality type with the numeric keypad.

      2. When adjusting the settings, use the number pad on the screen to input the voice quality type according to the table.

        Settings
        Parameter Target Phenomenon Voice Quality Type Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality

        A

        (Noise)

        The other party hears background noise when listening to your voice. 1000 The amount of background noise the other party hears when listening to your voice is reduced. The volume of voice the other party hears when listening to your voice may temporarily drop.

        B

        (Noise)

        The other party hears a lot of background noise when listening to your voice. 2000 The amount of background noise the other party hears when listening to your voice is sharply reduced. The volume of voice the other party hears when listening to your voice may temporarily drop.

        C

        (Echo)

        The other party hears weak echoes. 0100 The amount of echo is reduced (low level). Sound quality of the other party deteriorates (low level).

        D

        (Echo)

        The other party hears strong echoes. 0200 The amount of echo is reduced (high level). Sound quality of the other party deteriorates (high level).
        Settings (When Multiple Phenomenon Occurred)
        Parameter Target Phenomenon Voice Quality Type Positive Effect of Changing Voice Quality Negative Effect of Changing Voice Quality
        A+C The other party hears background noise and weak echoes when listening to your voice. 1100
        • The amount of background noise the other party hears when listening to your voice is reduced.

        • The amount of echo is reduced (low level).


        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (low level).

        A+D The other party hears background noise and strong echoes when listening to your voice. 1200
        • The amount of background noise the other party hears when listening to your voice is reduced.

        • The amount of echo is reduced (high level).


        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (high level).

        B+C The other party hears a lot of background noise and weak echoes when listening to your voice. 2100
        • The amount of background noise the other party hears when listening to your voice is sharply reduced.

        • The amount of echo is reduced (low level).


        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (low level).

        B+D The other party hears a lot of background noise and strong echoes when listening to your voice. 2200
        • The amount of background noise the other party hears when listening to your voice is sharply reduced.

        • The amount of echo is reduced (high level).


        • The volume of voice may drop temporarily.

        • Sound quality of the other party deteriorates (high level).

        Tech Tips


        • The default value is "0000".

        • Settings will be applied when the setting button is selected.

        • If voice quality type values that are not in the table are input, the setting will not be applied and a positive effect may not be gained.

        • If the quality of phone calls decreases due to the changed settings, return the settings to "0000" by selecting "INIT".

  13. CHECK DIGITAL TV RECEPTION (w/ Digital TV Function)

    Tech Tips


    • The reception condition of Digital TV (DTV) can be checked.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B0074ZQ

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A01VTCM

      Select "DTV reception check" from the "Function Check/Setting I" screen.

    4. B007689N01

      DTV reception check

      Screen Description
      Display Content
      *a: Up or down switch Enables the channel to be changed to the one to be checked.
      *b: Recheck/STOP switch
      • Recheck: Starts checking

      • STOP: Stops checking

      *c: Digital TV tuner reception level check result

        Displays digital TV antenna reception levels as follows:

      • 111 or more: Font color is black (good reception)

      • 110 or less: Font color is red (poor reception)

      • -: Not equipped with digital TV antenna

      *d: Antenna connection check

        Displays digital TV antenna connection status as follows:

      • OK: Connected properly

      • NG: Not connected properly

      • -: Not equipped with digital TV antenna

      Tech Tips


      • As digital TV is a terrestrial broadcast, the digital TV antenna cannot receive the signal in places where the signal may not reach the vehicle, such as mountains or tunnels.

      • Even in areas where digital TV broadcasts for households can be received, the in-vehicle digital TV may not be able to receive the broadcast.


      1. Select the "Recheck" button to start the DTV reception check.

      2. Check the result displayed when the DTV reception check is complete.

        Tech Tips


        • Do not depend solely on the reception level as a reference value as it may vary depending on the signal conditions such as wave interference.

        • If the result changes after turning the vehicle around, it is not a malfunction, but is caused by a local weak electric field.

        • If the reception level is abnormal, the antenna system or radio receiver assembly is malfunctioning.

  14. CHECK DAB RECEPTION (w/ DAB Function)

    Tech Tips


    • The reception condition of Digital Audio Broadcast (DAB) can be checked.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B0077IW

      Select "Function Check/Setting" from the "Service Menu" screen.

    3. A01VT4N

      Select "Next Page" from the "Function Check/Setting I" screen.

    4. B0073PO

      Select "DAB Reception Check" from the "Function Check/Setting II" screen.

    5. B0075TSN01

      DAB Reception Check

      Screen Description
      Display Content
      *a: Up or down switch Enables the channel to be changed to the one to be checked.
      *b: Check/STOP switch
      • Check: Starts checking

      • STOP: Stops checking

      *c: Antenna connection check

        DAB antenna connection status as follows:

      • OK: Connected properly

      • NG: Not connected properly

      • -: Not equipped with DAB antenna.

      *d: DAB Tuner Reception Level Check Result Description

        Displays DAB antenna reception levels as follows:

      • 111 or more: Font color is black (good reception)

      • 110 or less: Font color is red (poor reception)

      • -: Not equipped with DAB antenna.


      1. Select the "Check" button to start the DAB reception check.

      2. Check the result displayed when the DAB reception check is complete.

        Tech Tips

        If the reception level is abnormal, the antenna system or radio receiver assembly is malfunctioning.

  15. CLEAR PASSWORD OF EXPORT/IMPORT MEMORY POINT FUNCTION

    Tech Tips


    • This function allows the initialization of a password which was set on the radio receiver assembly when exporting/importing memory points.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Enter diagnostic mode.

      Click here

    2. B0075A0

      Select "Service Information" from the "Service Menu" screen.

    3. A01VSVD

      Select "Memory point backup" from the "Service Information" screen.

    4. B00746S

      Clear backup password

      Tech Tips

      Depending on the manufacturer, some component names and versions will be displayed differently.


      1. Select "Clear backup password" from the "Memory point backup" screen.

  16. CHECK SPEAKER

    Tech Tips


    • This function is used when checking the speaker wiring and whether the speakers are functioning properly.

    • Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.


    1. Turn audio mode on and play any audio source.

      Tech Tips

      This audio source will be used for the speaker check.

    2. Enter diagnostic mode.

      Click here

    3. B0074MZ

      Select "Failure Diagnosis" from the "Service Menu" screen.

    4. A01VSG3

      Select "System Check" from the "Failure Diagnosis" screen.

    5. A01VRF7

      Select "SP Check ON" from the "System Check Mode" screen.

    6. Check the speaker wiring and check that the speakers are functioning properly.

      Tech Tips


      • Check that each speaker outputs sound from the selected audio source properly.

      • "SP Check OFF" is displayed during the speaker check.

      • Sound can be heard from the speakers around the vehicle in order beginning from a speaker on the front side.

      • More than one speaker may sound simultaneously depending on the speaker wiring.

    7. Sound stops when any of the following conditions are met:


      1. "SP Check OFF" is selected.

      2. The engine switch is turned off.

      3. Diagnostic mode is turned off.

      4. The screen is changed to another screen.

      5. Audio mode is turned off.

  17. CHECK SOFTWARE ERROR HISTORY

    Tech Tips

    This function is used to check the cause when the radio receiver assembly screen is blacked out.


    1. Check software error history.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Software Error History.


        Body Electrical > Navigation System > Utility
        Tester Display
        Software Error History
      5. When an item is stored for Software Error History, record it before repairing the radio receiver assembly.

        Software Error History Screen Description
        Error Description Trigger Detail
        Software Reset Navi Microcomputer Hexadecimal Number
        Audio Microcomputer
        CAN Microcomputer
        No Video Signal Front Monitor
        Rear Monitor
        MOST Cold Restart Always

        Tech Tips


        • Software Error History can store up to 5 history data items. If a new software error occurs when 5 data items have already been stored, the oldest data is cleared and the new data is stored.

        • If an error that is unsupported by the GTS occurs, a "-" is displayed for the display items.

    2. Clear software error history.


      1. When DTCs are cleared using any of the following operations, Software Error History will be cleared as well.

        Click here


        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  18. CHECK OPTICAL DISC ERROR HISTORY

    Tech Tips

    This function is used to check the cause when an optical disc error occurs.


    1. Check optical disc error history.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Optical Disc Error History.


        Body Electrical > Navigation System > Utility
        Tester Display
        Optical Disc Error History
      5. When an item is stored for Optical Disc Error History, record it before proceeding with troubleshooting.

        Optical Disc Error History Screen Description
        Display Content
        Error Type Displays the type of error.
        Device Displays the malfunctioning device.
        Date Displays the date and time that the malfunction occurred.
        "Error Type" Screen Description
        Error Type Detection Condition Action
        Read Error When a disc read error occurs.

        Proceed to next suspected area shown in Problem Symptoms Table

        Click here

        Disc damaged/up side down/dirty

        When it is determined that any of the following is the cause of the disc read error:


        • The disc cannot be read.

        • The disc cannot be read because of dirt or scratches.

        • The disc cannot be read because it is inserted upside down.

        Cannot determine disc type An unsuitable disc is inserted.
        DPS error When an error occurs while decoding MP3/WMA/AAC files.
        Some files are corrupt
        • When MP3/WMA/AAC files cannot be played back because they are unsupported.

        • Even though the file extensions are MP3, WMA or AAC files cannot be played back because the header information cannot be read.

        Some files cannot be found
        • When a disc without music data is played back.

        • When there are no playable MP3/WMA/AAC files.

        Copy protection violation When a file with copyright protection that cannot be played back is played back.
        "Device" Screen Description
        Device Component
        DVD-P Radio receiver assembly
        CD-P Not available
        R-Seat DVD-P Not available

        Tech Tips


        • Optical Disc Error History can store up to 7 history data items. If a new optical disc error occurs when 7 data items have already been stored, the oldest data is cleared and the new data is stored.

        • If an error that is unsupported by the GTS occurs, a "-" or blank is displayed for the display items.

    2. Clear optical disc error history.


      1. When DTCs are cleared using any of the following operations, Optical Disc Error History will be cleared as well.

        Click here


        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  19. Tech Tips


    • This function is used to detect disconnection of the video devices.

    • In order to inspect the RSE, a disc should be inserted into the radio receiver assembly.

    CHECK VIDEO DEVICE CONNECTION CHECK


    1. Check Video Device Connection Check.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Video Device Connection Check.


        Body Electrical > Navigation System > Utility
        Tester Display
        Video Device Connection Check
      5. When an item is stored for Video Device Connection Check, record it before proceeding with troubleshooting.

        Tech Tips


        • DTCs are stored when errors are detected.

        • Depending on the vehicle, some of the items are not displayed on the "Error Detected Image Line (Type)" screen.

        Video Device Connection Check Screen Description
        Error Detected Image Line (Type) Areas to be Checked
        H/U - > Separate Display (GVIF) Digital video signal between the radio receiver assembly and multi-display assembly
        H/U - > Full RSE (GVIF) Not available
        RSE - > Seat Back Display RH (GVIF) Not available
        RSE - > Seat Back Display LH (GVIF) Not available
        Rear Camera - > H/U (NTSC) Not available
        IPA/BGM/PVM ECU - > Separate Display (GVIF) Not available
        IPA/BGM/PVM ECU - > H/U (NTSC) Not available
        IPA/BGM/PVM ECU - > H/U (GVIF) Not available
    2. Clear video device connection check.


      1. When DTCs are cleared using any of the following operations, Video Device Connection Check will be cleared as well.

        Click here


        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  20. MAP INFORMATION

    Tech Tips

    This function is used to check the map version of the navigation system and the end date of the map update service.


    1. Check map information.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / Map Information.


        Body Electrical > Navigation System > Utility
        Tester Display
        Map Information
      5. Check the map version and the end date of the map update service.

  21. CHECK "Wi-Fi" CONNECTION HISTORY (w/ "Wi-Fi" Function)

    Tech Tips

    This function is used to check the connection history when the connection between the radio receiver assembly and a "Wi-Fi" device is unstable.


    1. Check "Wi-Fi" Connection History.


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body Electrical / Navigation System / Utility / "Wi-Fi" Connection History.


        Body Electrical > Navigation System > Utility
        Tester Display
        Wi-Fi Connection History
      5. When an item is stored for "Wi-Fi" Connection History, record it before proceeding with troubleshooting.

        "Wi-Fi" Connection History Screen Description
        Item Content
        Occurrence Date/Time Year is displayed in 4 digits and month, date, hour, minute and second are displayed in 2 digits
        Result Connect/Disconnect Success
        Timeout
        Communication Error
        Authentication Failure
        Disconnection Failure
        Other Failure
        Contents No Error
        AP Connection Error
        AP Connection Error (WPS)
        DHCP Connection Error
        DNS Connection Error
        HTTP Connection Error
        Other Error
        Destination MAC Address Displayed in lower case hexadecimal format with "-" inserted every two characters.
        Destination SSID Data is read as ASCII code
        WLAN Standard 802.11 b
        802.11 g
        802.11 n
        Undetectability
        Received Signal Strength -127 dBm to +127 dBm
        Data Rate 1.0 Mbps
        2.0 Mbps
        5.5 Mbps
        6.0 Mbps
        6.5 Mbps
        9.0 Mbps
        11.0 Mbps
        12.0 Mbps
        13.0 Mbps
        18.0 Mbps
        19.5 Mbps
        24.0 Mbps
        26.0 Mbps
        36.0 Mbps
        39.0 Mbps
        48.0 Mbps
        52.0 Mbps
        54.0 Mbps
        58.5 Mbps
        65.0 Mbps
        Undetectability
        Packet Error Rate Displayed in decimal format with "%"

        Tech Tips

        If there is nothing to display in the "Content" column, "-" or "No Information" is displayed.

    2. Clear "Wi-Fi" connection history.


      1. When DTCs are cleared using any of the following operations, "Wi-Fi" Connection History will be cleared as well.

        Click here


        • Cleared using the GTS.

        • Cleared using the system check mode screen.

        • Cleared using the unit check mode screen.

  22. MAP DATA UPDATE ERROR CODE (w/ Sound Library Function)


    1. When updating the map data, the following error codes will be output if the update does not complete successfully. Perform the inspection according to the "Action to be Taken" column of each error code.

      Type of Update: 01 (Update via Communication)
      Error Code Error Occurrence Condition Cause of Error Navigation System Status Action to be Taken

      from 01 to 0F:

      File cannot be read or written

      01: Preparing for map data update
      • SD card (disc player disc) is not inserted or connected properly

      • Temporary failure due to external factors such as vibration or excessive temperature

      • Hardware malfunction

      Available
      1. Turn the engine switch off.

      2. Turn the engine switch on (ACC).

      3. Properly insert the SD card (disc player disc) and update the map data.

      4. If the same error code is output again, replace the SD card (disc player disc) and update the map data.

      5. If the same error code is output again, replace the radio receiver assembly.

      from 10 to 4F:

      Data mismatch notification from the map data distribution center

      Data sent by the map data distribution center is incorrect Available Contact the call center and check the integrity of the sent data.

      from 50 to 8F:

      Database malfunction

      During map data update, a database malfunction due to an unknown cause was detected. (The database automatically enters recovery mode and restores the previous data.) Available or cannot display map data
      1. Wait for the data to be restored.

      2. Properly insert the SD card (disc player disc) and update the map data.

      3. If the same error code is output again, replace the SD card (disc player disc) and update the map data.

      4. If the same error code is output again, replace the radio receiver assembly.

      Tech Tips

      Data restoration mode takes up to 3 hours with the engine switch on (ACC).

      from 90 to FF:

      Internal error

      Hardware failure Available
      1. Turn the engine switch off.

      2. Turn the engine switch on (ACC).

      3. Properly insert the SD card (disc player disc) and update the map data.

      4. If the same error code is output again, replace the SD card (disc player disc) and update the map data.

      5. If the same error code is output again, replace the radio receiver assembly.

      from 11 to 4F:

      File cannot be read or written

      21: Updating map module
      • SD card (disc player disc) is not inserted or connected properly

      • Temporary failure due to external factors such as vibration or excessive temperature

      • Hardware malfunction

      Available
      1. Turn the engine switch off.

      2. Turn the engine switch on (ACC).

      3. Properly insert the SD card (disc player disc) and update the map data.

      4. If the same error code is output again, replace the SD card (disc player disc) and update the map data.

      5. If the same error code is output again, replace the radio receiver assembly.

      from 51 to FF:

      System malfunction


      • Temporary failure due to external factors such as vibration or excessive temperature

      • Hardware malfunction

      Available
      1. Wait for the map data updated automatically again.

      2. If the same error code is output again, replace the SD card (disc player disc) and update the map data.

      3. If the same error code is output again, replace the radio receiver assembly.

      from 01 to 0F:

      File cannot be read or written

      02: Replacing map data
      • SD card (disc player disc) is not inserted or connected properly

      • Temporary failure due to external factors such as vibration or excessive temperature

      • Hardware malfunction

      Available
      1. Turn the engine switch off.

      2. Turn the engine switch on (ACC).

      3. Properly insert the SD card (disc player disc) and update the map data.

      4. If the same error code is output again, replace the SD card (disc player disc) and update the map data.

      5. If the same error code is output again, replace the radio receiver assembly.

      from 10 to 1F:

      Response timeout


      • Temporary failure due to external factors such as vibration or excessive temperature

      • Update is temporarily suspended due to software errors outside of the map data update function.

      Available
      1. Wait for the map data updated automatically again.

      2. If the same error code is output again, replace the SD card (disc player disc) and update the map data.

      3. If the same error code is output again, replace the radio receiver assembly.

      Tech Tips

      This error code is stored when communication fails due to heavy data loads during transmission.

      Type of Update: 03 (Update to Restore Data Using USB Device)
      Error Code Error Occurrence Condition Cause of Error Navigation System Status Action to be Taken

      from 01 to 2F:

      System malfunction

      01: Updating program (downloading)
      • Data corrupted during download

      • Data cannot be read due to problem with USB device.

      Available
      1. Using another USB device, obtain another update package and update the map data.

      2. If the same error code is output again, replace the SD card (disc player disc) and update the map data.

      3. If the same error code is output again, replace the radio receiver assembly.

      from 30 to 4F:

      Program update error


      • Temporary failure due to external factors such as vibration or excessive temperature

      • Hardware malfunction

      Available
      1. Using another USB device, obtain another update package and update the map data.

      2. If the same error code is output again, replace the SD card (disc player disc) and update the map data.

      3. If the same error code is output again, replace the radio receiver assembly.

      from 50 to FF:

      Internal error

      Hardware failure Available
      1. Using another USB device, obtain another update package and update the map data.

      2. If the same error code is output again, replace the SD card (disc player disc) and update the map data.

      3. If the same error code is output again, replace the radio receiver assembly.

      from 01 to 2F:

      System malfunction

      02: Updating program (installing)
      • Temporary failure due to external factors such as vibration or excessive temperature

      • Hardware malfunction

      Available
      1. Using another USB device, obtain another update package and update the map data.

      2. If the same error code is output again, replace the SD card (disc player disc) and update the map data.

      3. If the same error code is output again, replace the radio receiver assembly.

      from 30 to 4F:

      Program update error


      • Temporary failure due to external factors such as vibration or excessive temperature

      • Hardware malfunction

      Available
      1. Using another USB device, obtain another update package and update the map data.

      2. If the same error code is output again, replace the SD card (disc player disc) and update the map data.

      3. If the same error code is output again, replace the radio receiver assembly.

      from 50 to FF:

      Internal error

      Hardware failure Available
      1. Using another USB device, obtain another update package and update the map data.

      2. If the same error code is output again, replace the SD card (disc player disc) and update the map data.

      3. If the same error code is output again, replace the radio receiver assembly.

      from 01 to 2F:

      System malfunction

      03: Copying map data
      • Temporary failure due to external factors such as vibration or excessive temperature

      • Hardware malfunction

      Available or cannot display map data
      1. Using another USB device, obtain another update package and update the map data.

      2. If the same error code is output again, replace the SD card (disc player disc) and update the map data.

      3. If the same error code is output again, replace the radio receiver assembly.

      from 30 to 4F:

      File cannot be read or written


      • SD card (disc player disc) is not inserted or connected properly

      • Temporary failure due to external factors such as vibration or excessive temperature

      • Hardware malfunction

      Available or cannot display map data
      1. Using another USB device, obtain another update package and update the map data.

      2. Turn the engine switch off.

      3. Turn the engine switch on (ACC).

      4. Properly insert the SD card (disc player disc) and update the map data.

      5. If the same error code is output again, replace the SD card (disc player disc) and update the map data.

      6. If the same error code is output again, replace the radio receiver assembly.

      from 50 to 6F:

      Media update error


      • Data corrupted during download

      • Data cannot be read due to problem with USB device.

      Available or cannot display map data
      1. Using another USB device, obtain another update package and update the map data.

      2. If the same error code is output again, replace the SD card (disc player disc) and update the map data.

      3. If the same error code is output again, replace the radio receiver assembly.

      from 70 to 8F:

      File operation error


      • SD card (disc player disc) is not inserted or connected properly

      • Temporary failure due to external factors such as vibration or excessive temperature

      • Hardware malfunction

      Available or cannot display map data
      1. Using another USB device, obtain another update package and update the map data.

      2. Turn the engine switch off.

      3. Turn the engine switch on (ACC).

      4. Properly insert the SD card (disc player disc) and update the map data.

      5. If the same error code is output again, replace the SD card (disc player disc) and update the map data.

      6. If the same error code is output again, replace the radio receiver assembly.

      from 90 to FF:

      Internal error

      Hardware failure Available or cannot display map data
      1. Using another USB device, obtain another update package and update the map data.

      2. If the same error code is output again, replace the SD card (disc player disc) and update the map data.

      3. If the same error code is output again, replace the radio receiver assembly.

  23. ENFORM RESET PROCEDURE (w/ Enform Function)


    1. Duplicate the problem symptom.

    2. Check cellular phone compatibility.


      1. Check if the cellular phone/vehicle is compatible (Refer to http://www.lexus.com.au/).

      2. If the cellular phone is not compatible, recommend to the customer a compatible cellular phone.

    3. Delete all paired devices from the cellular phone.


      1. The procedure varies based on phone model. Contact the service provider or cellular phone manufacturer if assistance is required.

    4. Remove the Enform app from the phone.

      Note

      Only perform this step if the customer is present and approves.


      1. The procedure varies based on phone model. Contact the service provider or cellular phone manufacturer if assistance is required.

    5. Reset the phone.

      Note

      Only perform this step if the customer is present and approves.


      1. Turn off the phone and remove the battery for 15 seconds. For instructions on how to reset cellular devices, refer to the appropriate manufacturer's website.

    6. Reinstall the Enform app on the phone. (If removed.)


      1. The procedure varies based on phone model. Contact the service provider or cellular phone manufacturer if assistance is required.

    7. Delete all personal data from the head unit.


      1. Delete all personal data from the head unit.

        Note

        Only perform this step if the customer is present and approves.

        Tech Tips

        Re-installation of applications must be completed before applications will appear on the head unit.

    8. Disconnect the cable from the negative (-) battery terminal.

      Note

      After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

      Click here


      1. Record all radio station presets.

      2. Disconnect the cable from the negative (-) battery terminal and leave it disconnected for 2 minutes.

    9. Check if the problem symptom has been repaired.