PROCEDURE
INSPECT SPIRAL CABLE SUB-ASSEMBLY
If the steering sensor is installed to a misaligned spiral cable sub-assembly, DTCs for an abnormal steering sensor value, such as DTC B1801, C1231 and C1433, will be stored and it will be impossible to correct the problem. If this happens, replace the spiral cable with sensor sub-assembly with a new one.
Check if the spiral cable sub-assembly is centered.
*A | w/o Pre-crash Safety System | *B | w/ Pre-crash Safety System |
*a | Flat Cable | - | - |
When the spiral cable sub-assembly is centered, the part (A) is positioned at the top and the part of the flat cable shown in the illustration can be seen.
If the spiral cable sub-assembly is not centered, center it.
While pushing on the interlock shown in the illustration, rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.
*a | Interlock |
When rotating the spiral cable sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.
Do not turn the spiral cable sub-assembly using the airbag wire harness.
If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly or spiral cable with sensor sub-assembly with a new one.
While pushing on the interlock shown in the illustration, rotate the spiral cable sub-assembly clockwise approximately 2.5 times to the position where the part of the flat cable shown in the illustration can be seen.
*A | w/o Pre-crash Safety System | *B | w/ Pre-crash Safety System |
*a | Flat Cable | *b | Interlock |
The spiral cable sub-assembly can be rotated approximately 2.5 turns to both the left and right from the center.
INSTALL SPIRAL CABLE SUB-ASSEMBLY
Align the 2 pins and 2 guides, and engage the 6 claws to install the spiral cable sub-assembly to the steering sensor.
*a | Guide |
*b | Pin |
*c | Lock Pin |
Do not remove the lock pin before the spiral cable sub-assembly is installed to the steering sensor.
Do not damage the pins of the spiral cable sub-assembly and guides of the steering sensor.
The spiral cable sub-assembly can be rotated up to 30° even when the interlock is engaged. Therefore, make sure that both guides are aligned properly when installing the spiral cable sub-assembly to the steering sensor.
Remove the lock pin from the steering sensor.
INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).
Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the power switch on (IG).
Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the front wheels are aligned facing straight ahead.
Set the turn signal switch to the neutral position.
If it is not in the neutral position, the turn signal switch pin may snap.
Engage the 3 claws to install the spiral cable with sensor sub-assembly.
Connect each connector.
INSTALL UPPER STEERING COLUMN COVER
INSTALL LOWER STEERING COLUMN COVER (for Manual Tilt and Manual Telescopic Steering Column)
INSTALL LOWER STEERING COLUMN COVER (for Power Tilt and Power Telescopic Steering Column)
ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
Do not adjust the spiral cable with sensor sub-assembly with the auxiliary battery connected and the power switch on (IG).
Check that the power switch is off.
Check that the cable is disconnected from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
*A | w/o Pre-crash Safety System |
*B | w/ Pre-crash Safety System |
*a | Flat Cable |
Check if the spiral cable with sensor sub-assembly is centered.
When the spiral cable with sensor sub-assembly is centered, the part (A) is positioned at the top and the part of the flat cable shown in the illustration is visible.
If the spiral cable with sensor sub-assembly is not centered, center it.
*A | w/o Pre-crash Safety System |
*B | w/ Pre-crash Safety System |
*a | Interlock |
While pushing on the interlock indicated in the illustration, rotate the spiral cable with sensor sub-assembly counterclockwise slowly by hand until it stops.
When rotating the spiral cable with sensor sub-assembly, make sure to push on the interlock shown in the illustration to release the interlock mechanism.
Do not turn the spiral cable with sensor sub-assembly using the airbag wire harness.
*A | w/o Pre-crash Safety System |
*B | w/ Pre-crash Safety System |
*a | Interlock |
*b | Flat Cable |
While pushing on the interlock indicated in the illustration, rotate the spiral cable with sensor sub-assembly clockwise approximately 2.5 turns to the position where the part of the flat cable is visible.
The spiral cable with sensor sub-assembly can be rotate approximately 2.5 turns to both the left and right from the center.
INSTALL STEERING WHEEL ASSEMBLY
INSPECT STEERING WHEEL CENTER POINT
INSTALL HORN BUTTON ASSEMBLY
INSTALL LOWER NO. 3 STEERING WHEEL COVER
INSTALL LOWER NO. 2 STEERING WHEEL COVER
CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for Manual Tilt and Manual Telescopic Steering Column)
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for Power Tilt and Power Telescopic Steering Column)
INSTALL LUGGAGE TRIM SERVICE HOLE COVER
INSPECT HORN BUTTON ASSEMBLY
PERFORM DIAGNOSTIC SYSTEM CHECK
INSPECT SRS WARNING LIGHT
ADJUST PARKING ASSIST MONITOR SYSTEM
w/o Parallel Parking Assist Function: (Click here)
w/ Parallel Parking Assist Function: (Click here)