PROCEDURE
INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
When installing a new lower instrument panel assembly, No. 1 instrument panel sub-assembly or lower instrument panel sub-assembly:
Immediately before installing the lower instrument panel assembly, twist and cut off the portion as shown in the illustration.
Install the lower instrument panel sub-assembly with the 2 bolts <A>, 4 bolts <B>, 3 screws <C> or <G> and screw <D>.
*a | Bolt <A> | *b | Bolt <B> |
*c | Screw <C> or <G> | *d | Screw <D> |
*e | Clip | - | - |
Note
Do not damage the lower instrument panel sub-assembly.
Do not allow the wire harnesses to interfere with the surrounding parts.
If a screw <C> is loose and cannot be installed securely, replace it with a screw <G>.
Install the 2 clips.
Engage each clamp.
*A | w/ Digital Audio Broadcasting Antenna or Television Antenna | *B | w/ Telematics Transceiver |
Connect each connector.
Install in this Direction |
Engage the 2 claws to connect the cooler (room temp. sensor) thermistor as shown in the illustration.
Engage the 4 clips and 2 claws to connect the lower instrument cover sub-assembly to the upper steering column cover.
CONNECT NO. 2 INSTRUMENT PANEL WIRE
INSTALL GLOVE BOX LIGHT ASSEMBLY
INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
Install in this Direction |
Engage the 4 clips to install the No. 2 instrument panel register assembly as shown in the illustration.
INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
Install in this Direction |
Engage the 4 clips to install the No. 1 instrument panel register assembly as shown in the illustration.
INSTALL NO. 2 LOWER INSTRUMENT PANEL FINISH PANEL
Install in this Direction |
Engage the 9 clips to install the No. 2 lower instrument panel finish panel as shown in the illustration.
INSTALL SHIFT LEVER HOLE COVER
Connect each connector
Install in this Direction |
Engage the 5 clips to install the shift lever hole cover as shown in the illustration.
Engage the clamp.
INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Connect each connector
Engage each clamp.
Install in this Direction |
Engage the 5 clips to install the lower center instrument cluster finish panel sub-assembly as shown in the illustration.
INSTALL GLOVE COMPARTMENT DOOR STOPPER SUB-ASSEMBLY
Engage the claw to install the glove compartment door stopper sub-assembly.
INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY
Hold the glove compartment door assembly at an angle approximately 64.2° from its closed position and engage the 2 hinges horizontally as shown in the illustration.
*a | 64.2° | - | - |
Install in this Direction | - | - |
Note
Engaging the hinges from an upward angle will deform the hinges. Be sure to install the glove compartment door assembly horizontally.
*1 | Glove Compartment Door Stopper Sub-assembly |
Slightly bend the stoppers (A) and (B) in the directions indicated by the arrows shown in the illustration and engage the stoppers to install the glove compartment door assembly.
Engage the claw to connect the glove compartment door stopper sub-assembly.
INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Connect the connector.
Install in this Direction |
Engage the 2 guides as shown in the illustration.
Install in this Direction |
Engage the 3 claws to install the No. 2 instrument panel under cover sub-assembly as shown in the illustration.
INSTALL COWL SIDE TRIM BOARD RH
INSTALL FRONT DOOR SCUFF PLATE RH
INSTALL RADIO TUNER OPENING COVER WITH BRACKET (w/o Radio Receiver)
Engage the clamp.
Engage the 2 guides.
Install the radio tuner opening cover with bracket with the 4 bolts <B>.
INSTALL RADIO RECEIVER ASSEMBLY WITH BRACKET (for Radio and Display Type)
INSTALL NAVIGATION RECEIVER ASSEMBLY WITH BRACKET (for Navigation Receiver Type)
INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
Engage the clamp.
Connect each connector.
Engage the 5 guides and 18 clips to install the center instrument cluster finish panel sub-assembly as shown in the illustration.
Install in this Direction | - | - |
for LHD:
Install the clip.
INSTALL INSTRUMENT PANEL FINISH PANEL END RH
w/ Airbag Cut Off Switch:
Connect the connector.
Install in this Direction |
Engage the 3 guides as shown in the illustration.
Install in this Direction |
Engage the 6 clips to install the instrument panel finish panel end RH as shown in the illustration.
INSTALL COMBINATION METER ASSEMBLY
INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY
INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
Connect the connector.
Install in this Direction |
Engage the 2 guides and 6 clips as shown in the illustration.
Install the lower instrument panel finish panel assembly with the screw <C>.
CONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Engage the claw and 2 guides to connect the hood lock control lever sub-assembly.
INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
for RHD:
Engage the 2 claws to connect the DLC3 connector.
Engage the clamp.
Connect the connector.
Install in this Direction |
Engage the guide as shown in the illustration.
Install in this Direction |
Engage the claw as shown in the illustration.
Install the No. 1 instrument panel under cover sub-assembly with the 2 screws <F>.
INSTALL COWL SIDE TRIM BOARD LH
INSTALL FRONT DOOR SCUFF PLATE LH
INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY
Connect each connector.
Install in this Direction |
Engage the claw and 4 clips to install the instrument cluster finish panel garnish assembly as shown in the illustration.
INSTALL INSTRUMENT PANEL FINISH PANEL END LH
Install in this Direction |
Engage the 3 guides as shown in the illustration.
Install in this Direction |
Engage the 6 clips to install the instrument panel finish panel end LH as shown in the illustration.
INSTALL REAR CONSOLE BOX ASSEMBLY
INSTALL UPPER INSTRUMENT PANEL ASSEMBLY
CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
PERFORM DIAGNOSTIC SYSTEM CHECK
INSPECT SRS WARNING LIGHT