DTC Code | DTC Name |
---|---|
Check CAN Bus Line for Short to GND (RHD Models) |
DESCRIPTION
There may be a short circuit between one of the CAN bus lines and GND when there is no resistance between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of the DLC3.
Symptom | Trouble Area |
---|---|
No resistance exists between terminals 6 (CANH) and 4 (CG) or 14 (CANL) and 4 (CG) of DLC3. |
|
*: w/ Navigation system
CAUTION / NOTICE / HINT
Before measuring the resistance of the CAN bus, turn the power switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (Click here).
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output (Click here).
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the power switch on (IG), turn the cruise control main switch on, turn the blind spot monitor main switch on, wait at least 60 seconds and then drive the vehicle at a speed of 36 km/h (22 mph) or more for 7 seconds or more.
After the repair, perform CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed (Click here).
If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.
Operating the power switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines. When the connectors have been disconnected from the CAN junction connector, reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.
PROCEDURE
CHECK FOR SHORT TO GND IN CAN BUS LINE (DLC3 BRANCH LINE)
Disconnect the cable from the negative (-) auxiliary battery terminal.
Disconnect the H119 DLC3 branch line connector.
*a | Rear view of wire harness connector (to CAN Junction Connector RH1) |
*b | to DLC3 |
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
Measure the resistance according to the value(s) in the table below.
Standard Resistance | |||||||||
---|---|---|---|---|---|---|---|---|---|
|
*1 | DLC3 |
REPAIR OR REPLACE CAN BRANCH LINE CONNECTED TO DLC3
CHECK FOR SHORT TO GND IN CAN BUS LINE
Reconnect the H119 DLC3 branch line connector.
Disconnect the connectors from the CAN junction connector LH1 and CAN junction connector RH1 one at a time.
Disconnect the ECU and sensor connectors other than the DLC3 branch lines and CAN main bus lines between the CAN junction connector LH1 and CAN junction connector RH1.
*1 | DLC3 |
Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 4 (CG), and between terminals 14 (CANL) and 4 (CG) of the DLC3 each time a connector is disconnected.
*A | w/ Navigation System | - | - |
*1 | Power Management Control ECU | *2 | ECM |
*3 | Air Conditioning Amplifier Assembly | *4 | Airbag Sensor Assembly |
*5 | Main Body ECU (Multiplex Network Body ECU) | *6 | Power Steering ECU with Motor Assembly |
*7 | Multi-media Module Receiver Assembly | *8 | Combination Meter Assembly |
*9 | Clearance Warning ECU Assembly | *10 | DLC3 |
*11 | Brake Booster with Master Cylinder Assembly (Skid Control ECU) | *12 | Steering Sensor |
*13 | Certification ECU (Smart Key ECU Assembly) | *14 | CAN Junction Connector LH1 |
*15 | CAN Junction Connector RH1 | - | - |
*a | Component without harness connected (CAN Junction Connector RH1) |
- | - |
CAN Junction Connector RH1 Side | Code | Color (CANH Side) | Color (CANL Side) |
---|---|---|---|
CAN main bus line (bus line connecting CAN junction connector LH1 and CAN junction connector RH1) | H122 | R | W |
Combination meter assembly | H117 | G | W |
DLC3 | H119 | L | W |
Steering sensor | H120 | BE | W |
Certification ECU (smart key ECU assembly) | H127 | V | W |
Brake booster with master cylinder assembly (skid control ECU) | H131 | B | W |
Clearance warning ECU assembly | H132 | P | W |
*a | Component without harness connected (CAN Junction Connector LH1) |
- | - |
CAN Junction Connector LH1 Side | Code | Color (CANH Side) | Color (CANL Side) |
---|---|---|---|
Main body ECU (multiplex network body ECU) | H118 | V | W |
Power steering ECU with motor assembly | H121 | P | W |
CAN main bus line (bus line connecting CAN junction connector LH1 and CAN junction connector RH1) | H116 | R | W |
Air conditioning amplifier assembly | H123 | G | W |
Airbag sensor assembly | H124 | Y | W |
ECM | H125 | L | W |
Multi-media module receiver assembly* | H128 | BE | W |
Power management control ECU | H130 | B | W |
*: w/ Navigation system
Do not reconnect the disconnected connectors until this inspection is complete because there may be a short in 2 or more branch lines.
Result | ||||||
---|---|---|---|---|---|---|
|
When there is a short to GND in one or more of the bus lines that connect to an ECU (or sensor):
Reconnect all of the connectors to the CAN junction connectors, except for the one that was disconnected last (the bus line that is shorted to GND). Check that the resistance shown on the tester is normal (200 Ω or more) to confirm that there is a short to GND in the one branch line only.
Connectors that connect to the CAN junction connector can be distinguished by the color of their CAN bus lines.
Reconnecting the connectors to non-original positions on the CAN junction connector does not affect system performance. However, it is preferred to reconnect the connectors to their original positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.
When there is no short to GND in any of the bus lines that connect to the ECUs and sensors:
With all the specified connectors for ECUs and sensors disconnected, proceed with the inspection of the CAN bus main lines between the CAN junction connector LH1 and CAN junction connector RH1.
CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN J/C RH1)
Disconnect the H122 CAN main bus line connector.
*a | Rear view of wire harness connector (to CAN Junction Connector RH1) |
*b | to CAN Junction Connector LH1 |
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
Measure the resistance according to the value(s) in the table below.
Standard Resistance | |||||||||
---|---|---|---|---|---|---|---|---|---|
|
*1 | DLC3 |
REPLACE CAN JUNCTION CONNECTOR RH1
CHECK FOR SHORT TO GND IN CAN BUS LINE (CAN J/C LH1 - CAN J/C RH1)
Reconnect the H122 CAN main bus line connector.
Disconnect the H116 CAN main bus line connector.
*a | Rear view of wire harness connector (to CAN Junction Connector LH1) |
*b | to CAN Junction Connector RH1 |
Before disconnecting the connector, make a note of where it is connected.
Reconnect the connector to its original position.
Measure the resistance according to the value(s) in the table below.
Standard Resistance | |||||||||
---|---|---|---|---|---|---|---|---|---|
|
*1 | DLC3 |
REPLACE CAN JUNCTION CONNECTOR LH1
REPAIR OR REPLACE CAN MAIN BUS LINE (CAN J/C LH1 - CAN J/C RH1)
CHECK FOR SHORT TO GND IN CAN BUS LINE (ECU, SENSOR)
Reconnect the connector of the bus line that is shorted to GND to the CAN junction connector (the connector that caused the bus line resistance to change to 200 Ω or more when it was disconnected).
Disconnect the connector that includes the DLC3 connected CAN lines (such as CANH and CANL) from the ECU (or sensor) to which the bus line shorted to GND is connected (Click here).
Measure the resistance according to the value(s) in the table below.
Standard Resistance | |||||||||
---|---|---|---|---|---|---|---|---|---|
|
*1 | DLC3 |
If the resistance changes to 200 Ω or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).
REPLACE CORRESPONDING ECU OR SENSOR
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR