PROCEDURE
REMOVE FRONT SEAT ASSEMBLY LH
REMOVE FRONT SEAT ASSEMBLY RH
Tech Tips
Use the same procedure as for the LH side.
REMOVE REAR SEAT ASSEMBLY
REMOVE FRONT DOOR SCUFF PLATE LH
Disengage the 10 claws and remove the front door scuff plate LH.
REMOVE COWL SIDE TRIM BOARD LH
Remove the clip.
Disengage the claw and clip, and remove the cowl side trim board LH.
REMOVE FRONT DOOR OPENING TRIM COVER LH
Disengage the 3 claws and remove the front door opening trim cover LH.
REMOVE FRONT PILLAR GARNISH LH
*1 | Front Pillar Garnish Clip |
Pull the upper part of the front pillar garnish LH toward the inside of the cabin to disengage the clip and the front pillar garnish LH from the base of the front pillar garnish clip.
Tech Tips
Make the front pillar garnish LH hang from the front pillar garnish clip.
While pushing the tabs of the front pillar garnish clip in the direction indicated by the arrow (A) shown in the illustration, disengage the front pillar garnish clip.
Pull the garnish in the direction indicated by the arrow (B) shown in the illustration to disengage the 2 guides and remove the front pillar garnish LH.
*1 | Adhesive Tape |
*2 | Protective Cover |
*3 | Curtain Shield Airbag Assembly |
Protect the curtain shield airbag assembly.
Cover the airbag with a piece of cloth or nylon and secure the edges of the cover with tape as shown in the illustration.
Note
Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish LH is removed.
REMOVE REAR DOOR SCUFF PLATE LH
Disengage the 8 claws and remove the rear door scuff plate LH.
REMOVE CENTER PILLAR LOWER GARNISH LH
Disengage the 2 claws and 2 guides.
Disengage the 5 clips and remove the center pillar lower garnish LH.
REMOVE CENTER PILLAR UPPER GARNISH LH
Remove the 2 clips.
Disengage the clip as shown in the illustration.
Pass the floor anchor of the front seat outer belt assembly LH through the center pillar upper garnish LH and remove the center pillar upper garnish LH.
REMOVE FRONT DOOR SCUFF PLATE RH
Tech Tips
Use the same procedure as for the LH side.
REMOVE COWL SIDE TRIM BOARD RH
Tech Tips
Use the same procedure as for the LH side.
REMOVE FRONT DOOR OPENING TRIM COVER RH
Tech Tips
Use the same procedure as for the LH side.
REMOVE FRONT PILLAR GARNISH RH
Tech Tips
Use the same procedure as for the LH side.
REMOVE REAR DOOR SCUFF PLATE RH
Tech Tips
Use the same procedure as for the LH side.
REMOVE CENTER PILLAR LOWER GARNISH RH
Tech Tips
Use the same procedure as for the LH side.
REMOVE CENTER PILLAR UPPER GARNISH RH
Tech Tips
Use the same procedure as for the LH side.
REMOVE REAR SEAT SIDE GARNISH LH
Disengage the 5 claws and remove the rear seat side garnish LH.
REMOVE ROOF SIDE INNER GARNISH ASSEMBLY LH
Disengage the 4 clips.
Disengage the 2 guides and remove the roof side inner garnish assembly LH.
REMOVE REAR SEAT SIDE GARNISH RH
Tech Tips
Use the same procedure as for the LH side.
REMOVE ROOF SIDE INNER GARNISH ASSEMBLY RH
Tech Tips
Use the same procedure as for the LH side.
REMOVE LOWER SHIFT LEVER ASSEMBLY
U660E: Click here
U760E: Click here
U761E: Click here
REMOVE INSTRUMENT PANEL SAFETY PAD
REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/o Pre-crash Safety System)
REMOVE RAIN SENSOR COVER (w/o Pre-crash Safety System)
w/ Rain Sensor: Click here
REMOVE NO. 2 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)
REMOVE NO. 1 FORWARD RECOGNITION COVER (w/ Pre-crash Safety System)
REMOVE ROOF CONSOLE BOX ASSEMBLY
REMOVE SPOT LIGHT ASSEMBLY
REMOVE ASSIST GRIP SUB-ASSEMBLY
Tech Tips
Use the same procedure for the RH side.
*1 | Protective Tape |
Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.
Tech Tips
Tape the screwdriver tip before use.
Disengage the 2 clips and remove the assist grip sub-assembly.
Remove the 2 clips from the vehicle body.
REMOVE REAR ASSIST GRIP ASSEMBLY LH
*1 | Protective Tape |
Using a screwdriver, disengage the 4 claws and remove the 2 assist grip covers.
Tech Tips
Tape the screwdriver tip before use.
Disengage the 2 clips and remove the rear assist grip assembly LH.
Remove the 2 clips from the vehicle body.
REMOVE REAR ASSIST GRIP ASSEMBLY RH
Tech Tips
Use the same procedure as for the LH side.
REMOVE VISOR BRACKET COVER (for LH Side)
Using a moulding remover, disengage the 4 claws and remove the visor bracket cover.
REMOVE VISOR ASSEMBLY LH
Remove the 2 screws and visor assembly LH.
REMOVE VISOR BRACKET COVER (for RH Side)
Tech Tips
Use the same procedure as for the LH side.
REMOVE VISOR ASSEMBLY RH
Tech Tips
Use the same procedure as for the LH side.
REMOVE VISOR HOLDER
Tech Tips
Use the same procedure for the other visor holder.
*a | 45° |
Turn the visor holder approximately 45° and pull it out as shown in the illustration.
Disengage the 2 claws and remove the visor holder.
REMOVE ROOF HEADLINING ASSEMBLY (for Standard)
for Windshield Glass Side:
Disconnect each connector.
Disconnect the connector from the sliding roof drive gear sub-assembly.
*A | w/o Roof Antenna | *B | w/ Roof Antenna |
*1 | Clamp | *2 | Fastener |
*3 | Guide | - | - |
*a | Front Pillar LH | *b | Front Pillar RH |
*c | Rear Pillar RH | *d | Sliding Roof Drive Gear Sub-assembly |
Disengage the 3 clamps and disconnect the 2 connectors from the front pillar LH.
Disengage the 2 clamps from the front pillar RH.
w/o Roof Antenna:
Disengage the clamp and disconnect the connector from the rear pillar RH.
w/ Roof Antenna:
Disengage the clamp and disconnect the 2 connectors from the rear pillar RH.
Disengage the 12 claws and 11 fasteners.
Slide the roof headlining assembly to disengage the 3 clips and guide as shown in the illustration.
Tech Tips
Leave the 3 clips installed to the vehicle.
Remove the roof headlining assembly from the vehicle through the rear door as shown in the illustration.
Note
Do not damage the roof headlining assembly or vehicle interior.
Remove the 3 clips from the vehicle body as shown in the illustration.
REMOVE ROOF HEADLINING ASSEMBLY (for Glass Roof)
for Windshield Glass Side:
Disconnect each connector.
Disconnect the connector from the sliding roof drive gear sub-assembly.
*A | w/o Roof Antenna | *B | w/ Roof Antenna |
*1 | Clamp | *2 | Fastener |
*3 | Guide | - | - |
*a | Front Pillar LH | *b | Front Pillar RH |
*c | Rear Pillar RH | *d | Sliding Roof Drive Gear Sub-assembly |
Disengage the 3 clamps and disconnect the 2 connectors from the front pillar LH.
Disengage the 2 clamps from the front pillar RH.
w/o Roof Antenna:
Disengage the clamp and disconnect the connector from the rear pillar RH.
w/ Roof Antenna:
Disengage the clamp and disconnect the 2 connectors from the rear pillar RH.
Disengage the 12 claws and 23 fasteners.
Slide the roof headlining assembly to disengage the 3 clips and guide as shown in the illustration.
Tech Tips
Leave the 3 clips installed to the vehicle.
Remove the roof headlining assembly from the vehicle through the rear door as shown in the illustration.
Note
Do not damage the roof headlining assembly or vehicle interior.
Remove the 3 clips from the vehicle body as shown in the illustration.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Remove the front door opening trim weatherstrip LH.
Remove any residual weatherstrip sealant from the vehicle body using cleaner.
Note
Remove the sealant completely. Any residual sealant may transfer to other areas of the vehicle when removing/installing the interior parts.
REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Tech Tips
Use the same procedure as for the LH side.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
Remove the rear door opening trim weatherstrip LH.
Remove any residual weatherstrip sealant from the vehicle body using cleaner.
Note
Remove the sealant completely. Any residual sealant may transfer to other areas of the vehicle when removing/installing the interior parts.
REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH
Tech Tips
Use the same procedure as for the LH side.