PROCEDURE
PRECAUTION
Note
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (for 4 Sensor Type)
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
REMOVE DOOR SCUFF PLATE ASSEMBLY RH (for 4 Sensor Type)
*1 | Protective Tape |
Put protective tape around the door scuff plate assembly RH.
Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate assembly RH.
Tech Tips
Tape the screwdriver tip before use.
REMOVE COWL SIDE TRIM BOARD RH (for 4 Sensor Type)
Remove the clip.
Detach the clip and claw and remove the cowl side trim board RH.
REMOVE INSTRUMENT SIDE PANEL RH (for 4 Sensor Type)
*1 | Protective Tape |
Put protective tape around the instrument side panel RH.
Using a moulding remover, detach the 5 clips, claw and 3 guides and remove the instrument side panel RH.
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for 4 Sensor Type)
Detach the 4 clips.
Disconnect each connector and remove the lower instrument panel finish panel assembly.
REMOVE INSTRUMENT PANEL FINISH PLATE GARNISH (for 4 Sensor Type)
REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for 4 Sensor Type)
REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for 4 Sensor Type)
*1 | Protective Tape |
Using a screwdriver, detach the 2 claws and open the cover.
Tech Tips
Tape the screwdriver tip before use.
Remove the 2 bolts.
Detach the 14 clips.
Disconnect each connector and each cable and remove the lower instrument panel finish panel sub-assembly.
REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (for 4 Sensor Type)
Disconnect the connector.
Remove the 4 bolts and lower No. 1 instrument panel airbag assembly.
Note
When handling the airbag connector, take care not to damage the airbag wire harness.
REMOVE DRIVER SIDE JUNCTION BLOCK ASSEMBLY (for 4 Sensor Type)
REMOVE CLEARANCE WARNING ECU ASSEMBLY (for 4 Sensor Type)
Disconnect the connector.
Remove the bolt and clearance warning ECU assembly.
REMOVE DOOR SCUFF PLATE ASSEMBLY LH (for 8 Sensor Type)
*1 | Protective Tape |
Put protective tape around the door scuff plate assembly LH.
Using a screwdriver, detach the 4 clips, 10 claws and 2 guides and remove the door scuff plate assembly LH.
Tech Tips
Tape the screwdriver tip before use.
REMOVE COWL SIDE TRIM BOARD LH (for 8 Sensor Type)
Remove the clip.
Detach the clip and claw and remove the cowl side trim board LH.
REMOVE INSTRUMENT SIDE PANEL LH (for 8 Sensor Type)
*1 | Protective Tape |
Put protective tape around the instrument side panel LH.
Using a moulding remover, detach the 5 clips, claw and 3 guides and remove the instrument side panel LH.
REMOVE INSTRUMENT PANEL ORNAMENT (for 8 Sensor Type)
*1 | Protective Tape |
Put protective tape around the instrument panel ornament.
Using a moulding remover, detach the 5 clips and remove the instrument panel ornament.
REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (for 8 Sensor Type)
REMOVE GLOVE COMPARTMENT DOOR ASSEMBLY (for 8 Sensor Type)
*1 | Bolt |
*2 | Screw |
Remove the 2 bolts and 2 screws.
Detach the 5 clips and claw.
Disconnect each connector and remove the glove compartment door assembly.
REMOVE CLEARANCE WARNING ECU ASSEMBLY (for 8 Sensor Type)
Disconnect the connector.
Remove the 2 nuts and clearance warning ECU assembly.