CHARGING SYSTEM ON-VEHICLE INSPECTION

CAUTION / NOTICE / HINT

Note

If the battery is weak or if the engine is difficult to start, recharge the battery and perform inspections again before returning the vehicle to the customer.

PROCEDURE


  1. CHECK BATTERY CONDITION


    1. Check the battery for damage or deformation. If severe damage, deformation or leakage is found, replace the battery.

    2. Check the electrolyte level in each cell.


      1. For maintenance-free batteries:


        • If the electrolyte level is below the lower line, replace the battery.

        • If the electrolyte level is above the lower line, check the battery voltage when cranking the engine. If the voltage is less than 9.6 V, recharge or replace the battery.

          Tech Tips

          Before checking the battery voltage, turn off all the electrical systems (headlights, blower motor, rear defogger, etc.).

      2. B0042E9

        For non-maintenance-free batteries:


        • If the electrolyte level is below the lower line, add distilled water to each cell. Then, recharge the battery and check the electrolyte specific gravity.

          Standard Specific Gravity
          1.25 or higher at 20°C (68°F)
        • If the electrolyte level is above the lower line, check the battery voltage when cranking the engine. If the battery voltage is less than 9.6 V, recharge or replace the battery.

          Tech Tips

          Before checking the battery voltage, turn off all the electrical systems (headlights, blower motor, rear defogger, etc.).

    3. Check the voltage.


      1. Turn the ignition switch off and turn on the headlights for 20 to 30 seconds. This will remove the surface charge from the battery.

      2. Measure the battery voltage according to the value(s) in the table below.

        Standard Voltage
        Tester Connection Condition Specified Condition
        Positive (+) terminal - Negative (-) terminal 20°C (68°F) 12.3 V or higher

        If the result is not as specified, recharge or replace the battery.

  2. INSPECT BATTERY TERMINAL AND FUSE


    1. Check that the battery terminals are not loose or corroded.

      Torque:
      Positive (+) Battery Terminal
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }
      Negative (-) Battery Terminal
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      If the terminal is corroded, clean the terminal.

    2. Measure the resistance of the fuses.

      Standard Resistance
      Below 1 Ω

      If the result is not as specified, replace the fuse.

  3. INSPECT V-RIBBED BELT

    Click here

  4. INSPECT GENERATOR WIRING


    1. Visually check the generator wiring.


      1. Check that the wiring is in good condition.

  5. CHECK FOR ABNORMAL NOISE


    1. Listen for abnormal noises from the generator assembly.


      1. Check that no abnormal noises are heard from the generator assembly while the engine is running.

        If noise occurs, check the generator assembly.

        Click here

  6. INSPECT CHARGE WARNING LIGHT (FOR MULTI-INFORMATION DISPLAY (SEGMENT LCD TYPE))


    1. Turn the ignition switch to ON.

    2. Check that the charge warning light comes on.

    3. Start the engine and check that the charge warning light goes off.

      If the charge warning light does not operate as specified, troubleshoot the charge warning light.

      Click here

  7. INSPECT CHARGING CIRCUIT WITHOUT LOAD


    1. B0043LDC08
      *1 Battery
      *2 Generator Assembly
      *a Terminal B

      Connect a voltmeter and an ammeter to the charging circuit as follows.

      Tech Tips

      If a battery/generator assembly tester is available, connect the tester to the charging circuit in accordance with the manufacturer's instructions.


      1. Disconnect the wire from terminal B of the generator assembly, and then connect it to the negative (-) lead of the ammeter.

      2. Connect the ammeter positive (+) lead to terminal B of the generator assembly.

      3. Connect the voltmeter positive (+) lead to the terminal B of the generator assembly.

      4. Ground the voltmeter negative (-) lead.

    2. Check the charging circuit.


      1. Maintain the engine speed at 2000 rpm and check the readings on the ammeter and voltmeter.

        Standard Current
        10 A or more
        Standard Voltage
        13.2 to 14.8 V

        If the result is not as specified, repair or replace the generator assembly.

        Tech Tips

        If the result is not fully charged, the ammeter reading will sometimes be more than the standard current.

  8. INSPECT CHARGING CIRCUIT WITH LOAD


    1. With the engine running at 2000 rpm, turn the high beam headlights on and turn the heater blower switch to the "HI" position.

    2. Check the reading on the ammeter.

      Standard Current
      30 A or more

      If the result is not as specified, repair or replace the generator assembly.

      Tech Tips

      If the battery is fully charged, the reading will sometimes be less than the standard. If this is the case, add more electrical load (operate the wipers, rear window defogger, etc.) and check the reading on the ammeter again.