TOUCH SWITCH OUTLINE
Touch switches are touch-sensitive (interactive) switches operated by touching the screen. When a switch is pressed, the outer film bends in to contact the inner glass at the pressed position. By doing this, the voltage ratio is measured and the pressed position is detected.
DISC PLAYER OUTLINE
A disc player uses a laser pickup to read digital signals recorded on a disc. By converting the digital signals to analog, it can play music and audio.
CAUTION:
Do not look directly at the laser pickup because the disc player uses an invisible laser beam. Be sure to operate the player only as instructed.
Note
Do not disassemble any part of the disc player.
Do not apply oil to the disc player.
Do not insert anything but a disc into the disc player.
This player can play only audio CDs, CD-Rs (CD-Recordable) and CD-RWs (CD-ReWritable) that have any of the following marks:
This player can play only DVD videos that have any of the following marks (w/ DVD Player):
This player can play only DVD-Rs (DVD-Recordable) and DVD-RWs (DVD-ReWritable) that were recorded in video format and that have any of the following marks (w/ DVD Player):
The following products may not be playable on your player.
SACD
dts CD
Copy-protected CD
Precautions for use of discs
Note
CD-Rs and CD-RWs may not be played depending on the recording conditions or characteristics of the discs, or due to damage, dirt or deterioration caused by leaving the discs in the cabin for a long time.
Unfinalized CD-Rs and CD-RWs cannot be played.
CD-Rs and CD-RWs are more easily affected by a hot and humid environment than discs used for normal audio CDs. For this reason, some CD-Rs and CD-RWs may not be played.
If there are fingerprints or scratches on a disc, the disc may not play or may skip.
Some CD-Rs and CD-RWs may deteriorate if they are left in the cabin for a long time.
Keep CD-Rs and CD-RWs in an opaque case.
DualDiscs that mate DVD recorded material on one side with CD digital audio material on the other cannot be played.
Keep discs away from dirt. Be careful not to damage discs or leave fingerprints on them.
Hold discs by the outer edge and center hole with the label side up.
Leaving a disc exposed halfway out of the slot for a long time after pressing the disc eject button may cause deformation of the disc, making it unusable.
If discs have adhesive tape, stickers, disc labels or any traces of such labels attached, the discs may not be ejected or player malfunctions may result.
Keep discs away from direct sunlight. (Exposure to direct sunlight may cause deformation of a disc, making it unusable.)
Do not use odd-shaped discs because these may cause player malfunctions.
Do not use discs whose recording portion is transparent or translucent because they may not be inserted, ejected or played normally.
Use only 4.7 in. (12 cm) discs.
Do not use 3 in. (8 cm) discs either with or without adaptors.
Tech Tips
When it is cold or raining, if the windows fog up, mist and condensation may form in the player. In such cases, a disc may skip or stop in the middle of play. Ventilate or dehumidify the cabin for a while before using the player.
A disc may skip if the player experiences strong vibrations when the vehicle is driven on rough roads or similar uneven surfaces.
Cleaning
Note
Do not use a lens cleaner because it may cause a malfunction in the pickup portion of the player.
If dirt is on the disc surface, wipe it clean with a soft dry cloth, such as an eyeglass cleaner for plastic lenses, from the inside to the outside in a radial direction.
Note
Pressing on the disc by hand or rubbing the disc with a hard cloth may scratch the disc surface.
Use of solvents such as record spray, antistatic agents, alcohol, benzine, thinners or a chemical cloth may cause damage to the disc, making it unusable.
USB AUDIO SYSTEM FUNCTION OUTLINE
The No. 1 stereo jack adapter assembly is equipped with a USB connector. Connecting a USB device or "iPod" to the No. 1 stereo jack adapter assembly allows music files to be played. Not only is it possible to play music from a USB device with audio functions, it is also possible to play MP3, WMA or AAC music files that are stored on a USB device. In addition, "iPod" control software is installed, allowing file selection from playlists and operation using shuffle mode.
Tech Tips
Operation through the controls of a USB device or "iPod" cannot be performed while it is connected.
USB audio system compatible devices
USB device
The following device formats can be used:
Compatible USB device formats |
|
MP3, WMA and AAC files written to a USB device with any format other than those listed above may not play correctly, and their names and folder names may not be displayed correctly.
Items related to standards and limitations are as follows:
Maximum directory hierarchy: 8 levels
Maximum number of folders in device: 3000 (including the root folder)
Maximum number of files in device: 9999
Maximum number of files per folder: 255
"iPod"
"iPhone", "iPod", "iPod classic", "iPod nano" and "iPod touch" are trademarks of Apple Inc., registered in the U.S. and other countries.
The following "iPod", "iPod nano", "iPod classic", "iPod touch" and "iPhone" devices can be used with this system.
Made for:
"iPod touch" (5th generation)
"iPod touch" (4th generation)
"iPod touch" (3rd generation)
"iPod touch" (2nd generation)
"iPod touch" (1st generation)
"iPod classic"
"iPod with video"
"iPod nano" (7th generation)
"iPod nano" (6th generation)
"iPod nano" (5th generation)
"iPod nano" (4th generation)
"iPod nano" (3rd generation)
"iPod nano" (2nd generation)
"iPod nano" (1st generation)
"iPhone 5"
"iPhone 4S"
"iPhone 4"
"iPhone 3GS"
"iPhone 3G"
"iPhone"
Tech Tips
Depending on differences between models or software versions etc., some models might be incompatible with this system.
MP3/WMA/AAC OUTLINE
Playable MP3 file standards
Compatible standard | MPEG1 LAYER3, MPEG2 LSF LAYER3 |
Compatible sampling frequency |
|
Compatible bit rate |
|
Compatible channel mode | Stereo, joint stereo, dual channel, monaural |
Playable WMA file standards
Compatible standard | WMA Ver. 7, 8, and 9 |
Compatible sampling frequency | 32, 44.1, 48 (kHz) |
Compatible bit rate (Only compatible with 2-channel playback) |
|
Playable AAC file standards
Compatible standard | MPEG4/AAC-LC |
Compatible sampling frequency | 11.025, 12, 16, 22.05, 24, 32, 44.1, 48 (kHz) |
Compatible bit rate |
|
ID3 tag, WMA tag and AAC tag
Additional text information called an ID3 tag can be input to MP3 files. Information such as song titles and artist names can be stored.
Tech Tips
This player is compatible with ID3 tags of ID3 Ver. 1.0 and 1.1, and ID3 Ver. 2.2 and 2.3. (Number of characters complies with ID3 Ver. 1.0 and 1.1.)
Additional text information called a WMA tag can be input to WMA files. Information such as song titles and artist names can be stored.
Additional text information called an AAC tag can be input to AAC files. Information such as song titles and artist names can be stored.
Usable media
Only CD-ROMs, CD-Rs (CD-Recordable), CD-RWs (CD-ReWritable) and USB devices can be used to play MP3/WMA/AAC files.
Note
CD-Rs and CD-RWs are more easily affected by a hot and humid environment than discs used for normal audio CDs. For this reason, some CD-Rs and CD-RWs may not be played.
If there are fingerprints or scratches on a disc, the disc may not play or may skip.
Some CD-Rs and CD-RWs may deteriorate if they are left in the cabin for a long time.
Keep CD-Rs and CD-RWs in an opaque case.
Usable media format
Usable media format
Disc format | CD-ROM Mode 1, CD-ROM XA Mode 2 Form 1 |
File format | ISO9660 Level 1 and Level 2 (Joliet, Romeo) |
Tech Tips
MP3/WMA/AAC files written in any unlisted format may not be played normally or the file names or folder names may not be displayed correctly.
This player is compatible with multi-session discs and can play CD-Rs and CD-RWs on which MP3/WMA/AAC files have been added. However, only the first session can be played.
Discs whose first session includes both music data and MP3, WMA and AAC format data may not be played.
Standards and restrictions
Maximum directory levels | 8 levels |
Maximum number of characters for a folder name/file name | 32 characters |
Maximum number of folders | 192 (Including empty folders, root folders, and folders that do not contain MP3/WMA/AAC files) |
Maximum number of files in a disc | 255 (Including non-MP3/WMA/AAC files) |
File names
Only files with an extension of ".mp3", ".wma" and ".m4a" can be recognized and played as MP3, WMA or AAC files.
Save MP3, WMA or AAC files with an extension of ".mp3", ".wma" or ".m4a".
Note
If non-MP3, non-WMA or non-AAC files are saved with an extension of ".mp3", ".wma" or ".m4a", those files may be wrongly recognized as MP3, WMA or AAC files and played. A loud noise may occur and damage to the speakers may result.
"Bluetooth" OUTLINE
*1 | Radio and Display Receiver Assembly (Built-in "Bluetooth" Antenna) |
- | - |
*a | Example | *b | Cellular Network |
*c | Cellular Phone ("Bluetooth" Compatible Type) |
*d | Portable Audio Player ("Bluetooth" Compatible Type) |
*e | "Bluetooth" Wireless Connection | - | - |
"Bluetooth" is a trademark owned by Bluetooth SIG, Inc.
"Bluetooth" is a wireless connection technology that uses the 2.4 GHz frequency band.
Tech Tips
The communication performance of "Bluetooth" may vary depending on obstructions or radio wave conditions between communication devices, electromagnetic radiation, communication device sensitivity or antenna capacity.
Hands-free function
The "Bluetooth" built-in radio and display receiver assembly and a "Bluetooth" compatible cellular phone* can be connected using a "Bluetooth" wireless connection. This enables the use of the hands-free function on the cellular phone even if the phone is in a pocket or bag. For this reason, it is not necessary to use a connector or cable to connect the cellular phone.
*: Some versions of "Bluetooth" compatible cellular phones may not function properly.
The hands-free function uses a "Bluetooth" wireless connection. A "Bluetooth" wireless connection can be affected by uncertain elements, such as vehicle location, time of day, etc. Therefore, problems related to establishing connection may be caused temporarily by "Bluetooth" connection conditions. It is necessary to check the frequency of occurrence, connection conditions using another cellular phone, etc. when performing diagnosis.
Compatible hands-free devices
Required "Bluetooth" specifications | Ver. 2.0 or higher (Ver. 3.0+EDR recommended) |
Compatible profiles |
|
Maximum number of hands-free devices that can be registered (including audio devices) | 5 |
*1: This profile is necessary when using the hands-free function.
*2: This profile is necessary when using the message function (w/ SMS/MMS/e-mail Function).
*3: This profile is necessary when using the Toyota Link Function (w/ Toyota Link Function).
Tech Tips
The amount of remaining battery charge displayed on the radio and display receiver assembly may be different from that of the "Bluetooth" device.
"Bluetooth" audio function
The "Bluetooth" built-in radio and display receiver assembly and a "Bluetooth" compatible portable audio player* can be connected using a "Bluetooth" wireless connection. This enables files stored in the portable audio player to be heard from the vehicle speakers. In addition, operations such as play/stop can be performed directly from the radio and display receiver assembly.
*: Some versions of "Bluetooth" compatible audio players may not be able to be connected via the "Bluetooth" function, or music may play, but functions available using the radio and display receiver assembly may be limited.
Compatible "Bluetooth" audio devices
Required "Bluetooth" specifications | Ver. 2.0 or higher (Ver. 3.0+EDR recommended) |
Compatible profiles |
|
Maximum number of audio devices that can be registered (including hands-free devices) | 5 |
Tech Tips
The amount of remaining battery charge displayed on the radio and display receiver assembly may be different from that of the "Bluetooth" device.
RADIO DESCRIPTION
Radio frequency band
Radio broadcasts use the radio frequency bands shown in the table below.
Service area
*a | FM (Stereo) |
*b | FM (Monaural) |
*c | AM |
The service areas of AM and FM broadcasts are vastly different. Sometimes an AM broadcast can be received very clearly but an FM stereo broadcast cannot. FM stereo has the smallest service area, and is prone to pick up static and other types of interference such as noise.
Radio reception problems
Tech Tips
In addition to static, other problems such as "phasing", "multipath" and "fade out" exist. These problems are not caused by electrical noise, but by the radio signal propagation method itself.
*a | Phasing |
*b | Ionosphere |
Phasing
AM broadcasts are susceptible to electrical interference and another kind of interference called phasing. Occurring only at night, phasing is the interference created when a vehicle receives 2 radio wave signals from the same transmitter. One signal is reflected off the ionosphere and the other signal is received directly from the transmitter.
*a | Multipath |
Multipath
Multipath is a type of interference created when a vehicle receives 2 radio wave signals from the same transmitter. One signal is reflected off buildings or mountains and the other signal is received directly from the transmitter.
*a | Fade Out |
Fade out
Fade out is caused by objects (buildings, mountains and other large obstructions) that deflect part of a signal, resulting in a weaker signal when the object is between the transmitter and vehicle. High frequency radio waves, such as FM broadcasts, are easily deflected by obstructions. Low frequency radio waves, such as AM broadcasts, are less likely to be deflected.
Noise problem
Technicians must have a clear understanding about each customer's noise complaint. Use the following table to diagnose noise problems.
Radio Frequency | Noise Occurrence Condition | Presumable Cause |
---|---|---|
AM | Noise occurs in a specific area | Foreign noise |
Noise occurs when listening to an intermittent broadcast | An identical program transmitted from multiple towers can cause noise where the signals overlap | |
Noise occurs only at night | Signal phasing | |
FM | Noise occurs while driving in a specific area | Multipath resulting from a change in FM frequency |
VEHICLE CUSTOMIZATION OUTLINE
Customization of functions can also be performed on the multi-display screen. Refer to Owner's Manual for further information on customizable items for the audio and visual system.
Tech Tips
Items available for customization via the audio and visual system can also be customized by using the GTS.
Some customize parameters displayed on the GTS will be displayed on the vehicle customization screen of the audio and visual system. Users can customize these items.
AUTOMATIC SOUND LEVELIZER (ASL) FUNCTION OUTLINE
The Automatic Sound Levelizer (ASL) function automatically adjusts the audio system volume level in order to compensate for increased vehicle noise (vehicle noise tends to increase as vehicle speed increases). The ASL adjusts the volume level based on vehicle speed signals sent from the meter circuit plate.
COMMUNICATION SYSTEM
CAN Communication Outline
The audio and visual system uses CAN communication between the radio and display receiver assembly and ECUs.
AVC-LAN Outline (for 10 Speakers)
*a | Example | *b | AVC-LAN Communication Line |
*c | Master Unit | *d | Slave Unit |
Components of the audio and visual system communicate with each other via AVC-LAN communication.
The AVC-LAN uses a twisted pair of wires for its communication lines.
The master unit of the AVC-LAN is the radio and display receiver assembly.
Tech Tips
The radio and display receiver assembly has the resistance (60 to 80 Ω) necessary for communication.
If a short or open occurs in the AVC-LAN circuit, communication is interrupted and the system will not operate normally.
Local Bus Communication Outline
*a | Example | *b | Local Bus Communication Line |
*c | Master Unit | *d | Slave Unit |
Components of the audio and visual system communicate with each other via the local bus.
The local bus uses a twisted pair of wires for its communication lines.
The master unit of the local bus is the radio and display receiver assembly.
Tech Tips
The radio and display receiver assembly has the resistance (108 to 132 Ω) necessary for communication.
If a short or open occurs in the local bus circuit, communication is interrupted and the system will not operate normally.
DIAGNOSTIC FUNCTION OUTLINE
The audio and visual system has a diagnostic function (the result is indicated on the master unit).
MIRRORLINK FUNCTION OUTLINE (w/ "MirrorLink" Function)
"MirrorLink" is a function that enables the radio and display receiver assembly to operate applications on a smartphone which meets Car Connectivity Consortium standards by connecting the smartphone to the radio and display receiver assembly with a USB cable.
"MirrorLink" compatible smartphone manufacturers and applications are listed below.
for Ver. 1.0 compatible:
Manufacturer | Device | Application (available area/country) |
---|---|---|
Nokia |
|
|
Samsung | Galaxy S3 | DriveLink (for Europe, Southeast Asia) |
for Ver. 1.1 or later compatible:
Only smartphones which have passed the Car Connectivity Consortium MirrorLink 1.1 Certification Program are compatible.
For details, refer to http://carconnectivity.org/ and http://www.mirrorlink.com/
For details about MirrorLink compatibility, contact the smartphone manufacturer.
Tech Tips
The "MirrorLink" version may vary depending on the radio and display receiver assembly. If the radio and display receiver assembly supports "MirrorLink" Ver. 1.0, only smartphones listed in the above compatibility chart are supported.
Some applications require payment.
The names of applications are subject to change.
Some applications have a display restriction in consideration of safe driving.
DIGITAL AUDIO BROADCAST (DAB) FUNCTION OUTLINE (w/ DAB Function)
Digital Audio Broadcast (DAB) is the standard for digital radio. Compared to conventional AM/FM broadcasting, DAB enables higher sound quality radio broadcasting with lower noise when reception conditions change. DAB has an FM-Link function that automatically and temporarily changes the radio to the simultaneously broadcasted FM station if the DAB broadcasting reception level falls.
TOYOTA LINK FUNCTION OUTLINE (w/ Toyota Link Function)
Toyota Link is a service that enables Toyota Link applications and content of a cellular phone to be displayed on and operated from the multi-display. As "Bluetooth" communication is used for the communication between a cellular phone and the radio and display receiver assembly, before using the Toyota Link service on the audio and visual system, the cellular phone needs to be registered with the audio and visual system as a "Bluetooth" device. For details regarding Toyota Link operations, each of the applications and compatible phones, refer to http://www.toyota.com.au/owners.