REAR SEAT ASSEMBLY(for 60/40 Split Seat Type LH Side) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seat frame may injure your hands.

PROCEDURE


  1. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY LH


    1. B007Z89C01
      B007Z37 Install in this Direction

      Using a T40 "TORX" socket wrench, install the rear seatback frame sub-assembly LH to the rear seat cushion frame sub-assembly LH with the 5 bolts as shown in the illustration.

      Torque:
      29 N*m  { 296 kgf*cm, 21 ft.*lbf }
    2. B007XJZC01
      B007Z37 Install in this Direction

      Engage the clamp to install the joint case as shown in the illustration.

  2. INSTALL REAR SEAT LEG PLATE SUB-ASSEMBLY LH


    1. A01VUGB

      Install the rear seat leg plate sub-assembly LH with the nut.

      Torque:
      7.5 N*m  { 76 kgf*cm, 66 in.*lbf }
  3. INSTALL NO. 2 REAR SEAT RECLINING CONTROL CABLE (for Manual Seat)


    1. A01VXM0

      Connect the 6 cable clamps to install the No. 2 rear seat reclining control cable.

    2. Engage the 5 clamps.

  4. INSTALL RECLINING ADJUSTER INSIDE COVER RH


    1. A01VY2S

      Engage the 2 claws to install the reclining adjuster inside cover RH.

  5. INSTALL RECLINING ADJUSTER INSIDE COVER LH


    1. A01VVSD

      Engage the guide and claw to install the reclining adjuster inside cover LH.

  6. INSTALL REAR SEAT INNER RECLINING COVER LH


    1. B007X6QC01
      B007Z37 Install in this Direction (1)
      B007YXL Install in this Direction (2)

      Engage the 6 guides and 7 claws as indicated by the arrows, in the order shown in the illustration to install the rear seat inner reclining cover LH.

  7. INSTALL REAR SEATBACK MOULDING LH


    1. B007XZVC01
      B007Z37 Install in this Direction (1)
      B007YXL Install in this Direction (2)

      Engage the 6 guides and 7 claws as indicated by the arrows, in the order shown in the illustration to install the rear seatback moulding LH.

  8. INSTALL NO. 2 RECLINING LINK COVER RH (for Manual Seat)


    1. B008032C01
      B007Z37 Install in this Direction

      Engage the guide to install the No. 2 reclining link cover RH as shown in the illustration.

  9. INSTALL NO. 1 RECLINING LINK COVER RH (for Manual Seat)


    1. B007ZBKC01
      B007Z37 Install in this Direction

      Engage the guide and 5 claws to install the No. 1 reclining link cover RH as shown in the illustration.

  10. INSTALL NO. 2 RECLINING LINK COVER LH (for Manual Seat)


    1. B007ZPTC02
      B007Z37 Install in this Direction

      Engage the guide to install the No. 2 reclining link cover LH as shown in the illustration.

  11. INSTALL NO. 1 RECLINING LINK COVER LH (for Manual Seat)


    1. B007YRGC01
      B007Z37 Install in this Direction

      Engage the guide and 5 claws to install the No. 1 reclining link cover LH as shown in the illustration.

  12. INSTALL REAR SEAT WIRE LH (for Power Seat)


    1. A01VX7U

      Engage the 2 clamps and install the rear seat wire LH

    2. Connect the 2 connectors.

  13. INSTALL FOLD SEAT CONTROL ECU (for Power Seat)


    1. B007X2YC02
      B007Z37 Install in this Direction

      Connect the 2 connectors and install the fold seat control ECU as shown in the illustration.

  14. INSTALL REAR SEATBACK PROTECTOR


    1. B007ZTCC01

      Install the rear seatback protector with the 2 nuts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
  15. INSTALL REAR SEAT AIRBAG ASSEMBLY LH

    Click here

  16. INSTALL SEATBACK FELT LH


    1. A01VY3E

      Install a new seatback felt LH.

  17. INSTALL SEAT COVER WIRE


    1. B007YGRN01

      Install the 5 seat cover wires.

      Tech Tips


      • Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.


      • For wire 1000 mm (3.28 ft.) or less in length, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.


      • Make sure to read the precautions before preparing the wire.

        Click here

      Length
      A 130 mm (5.12 in.)
      B 330 mm (1.0824 ft.)
      C Available as a supply part.

      Tech Tips

      The dimension shown in the illustration is the length.

      B005NZL
  18. INSTALL SEPARATE TYPE REAR SEATBACK COVER

    Tech Tips

    When installing a separate type rear seatback cover, refer to Precaution in order to prevent wrinkles from forming.

    Click here


    1. B007YHCN01

      Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 11 new hog rings in the order shown in the illustration.

      Note


      • Be careful not to damage the separate type rear seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.

  19. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD


    1. Temporarily install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly.

    2. A01VWX4

      Install the 2 rear seatback cover brackets with the nut.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Note


      • For vehicles with a rear seat airbag assembly, the separate type rear seatback cover with pad must be securely installed. Otherwise, the rear seat airbag assembly may not deploy properly.

      • Make sure that the strap is not twisted after installing the nut.

      • Make sure that the brackets are installed securely.

    3. for Manual Seat:


      1. A01VVQD

        Engage the 2 hooks.

      2. B007XUBC01
        B007ZL6 Fastener

        Engage the fastener.

    4. B007YXEC02
      B007Z37 Install in this Direction

      Engage the 4 claws to install the 2 rear No. 1 seat headrest supports as shown in the illustration.

    5. A01VWWP

      Engage each hook to install the separate type rear seatback cover with pad.

  20. INSTALL REAR SEATBACK BOARD CARPET ASSEMBLY LH


    1. A01RD4D

      Engage the 3 guides as shown in the illustration.

    2. B007Z93C01
      B007Z37 Install in this Direction

      Engage the 2 guides and 4 clips as shown in the illustration.

    3. A01VVGC

      Engage the 2 hooks to install the rear seatback board carpet assembly LH.

  21. INSTALL REAR SEATBACK COVER LH


    1. B007ZYKC01
      B007Z37 Install in this Direction

      Engage the 6 claws to install the rear seatback cover LH as shown in the illustration.

    2. B005MVQ

      Engage the 2 claws as shown in the illustration.

  22. INSTALL REAR SEAT INNER BELT ASSEMBLY LH

    Click here

  23. INSTALL SEAT COVER WIRE


    1. B007WRKN01

      Install the 6 seat cover wires.

      Tech Tips


      • Wire 1000 mm (3.28 ft.) or longer and shaped wire are available as supplied parts.


      • For wire 1000 mm (3.28 ft.) or less in length, cut or shape 1000 mm (3.28 ft.) wire into the dimensions shown in the illustration.


      • Make sure to read the precautions before preparing the wire.

      Length
      A 420 mm (1.3776 ft.)
      B 240 mm (9.45 in.)
      C 90 mm (3.54 in.)

      Tech Tips

      The dimension shown in the illustration is the length.

      B005NZL
  24. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER

    Tech Tips

    When installing a separate type rear seat cushion cover, refer to Precaution in order to prevent wrinkles from forming.

    Click here


    1. B007YCWN01

      Using hog ring pliers, install the separate type rear seat cushion cover to the separate type rear seat cushion pad with 20 new hog rings in the order shown in the illustration.

      Note


      • Be careful not to damage the separate type rear seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.

    2. B007Z3PN01

      Using hog ring pliers, install 6 new hog rings in the order shown in the illustration.

      Note


      • Be careful not to damage the separate type rear seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.

    3. B008040C01
      B007ZL6 Fastener

      Engage the fastener.

  25. INSTALL SEAT CUSHION FELT LH


    1. A01VV2W

      Install a new seat cushion felt LH.

  26. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD


    1. Temporarily install the separate type rear cushion cover with pad to the rear seat cushion frame sub-assembly LH.

    2. A01VV5K

      Engage each hook to install the separate type rear seat cushion cover with pad.

    3. B007XFVC04
      *A w/ Seat Heater System

      for Manual Seat:


      1. Engage the clamp.

      2. w/ Seat Heater System:


        1. Engage the 2 clamps.

        2. Connect the connector.

    4. B007XG5C02
      *A w/ Seat Heater System

      for Power Seat:


      1. w/ Seat Heater System:


        1. Engage the 2 clamps.

        2. Connect the connector.

      2. Engage the 2 clamps.

    5. A01VX90

      Connect the rubber band.

  27. INSTALL CONNECTOR MALE HOUSING (for Manual Seat)


    1. w/o Seat Heater System:


      1. A01VUJT

        Engage the clamp to install the connector male housing.

  28. INSTALL CONNECTOR BRACKET (w/o Seat Belt Warning System)


    1. B007X1HC01
      B007Z37 Install in this Direction

      Engage the claw as shown in the illustration to install the connector bracket.

  29. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY (w/ Seat Heater System)


    1. B007YRH

      Engage the 2 clamps to install the seat heater control sub-assembly.

    2. Connect the 2 connectors.

  30. CONNECT SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD


    1. B007WOA

      Engage the 2 hooks to connect the separate type rear seat cushion cover with pad.

  31. INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH (for Manual Seat)


    1. A01VY5N

      Install the No. 1 reclining adjuster release handle LH with the 3 screws.

  32. INSTALL REAR SEAT COVER CAP LH (for Manual Seat)


    1. A01R9VB

      Engage the 2 claws to install the rear seat cover cap LH.

  33. INSTALL REAR POWER SEAT SWITCH LH (for Power Seat)


    1. B007ZSAC01
      B007Z37 Install in this Direction

      Engage the 2 claws to install the rear power seat switch LH as shown in the illustration.

  34. INSTALL POWER SEAT SWITCH ASSEMBLY (for Power Seat)


    1. B005Q8N

      Connect the connector.

    2. B007WXYC02
      B007Z37 Install in this Direction

      Engage the 2 claws to install the power seat switch assembly as shown in the illustration.

  35. INSTALL REAR CENTER SEAT INNER BELT ASSEMBLY

    Click here