CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during radiator assembly removal/installation are shown below.
Replaced Part or Performed Procedure | Necessary Procedure | Effect/Inoperative Function when Necessary Procedure not Performed | Link |
---|---|---|---|
Battery terminal is disconnected/reconnected | Memorize steering angle neutral point | LKA /LDA system | |
Pre-crash safety system | |||
Lighting system (EXT)
|
|||
Adaptive high beam system | |||
Drive the vehicle until stop and start control is permitted (approximately 15 to 60 minutes) | Stop and start system | ||
Memorize steering angle neutral point | Parking assist monitor system (w/ Parallel parking assist function) | ||
Parking assist monitor system (w/o Parallel parking assist function) | |||
Panoramic view monitor system | |||
Initialize back door lock | Power door lock control system | ||
Reset back door close position | Power back door system | ||
Replacement of battery |
|
Stop and start system | |
|
Front television camera view adjustment | Panoramic view monitor system | Click here for Initialization Click here for Calibration |
PROCEDURE
PRECAUTION
Note
After turning the engine switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
REMOVE FRONT WHEEL OPENING EXTENSION PAD LH
REMOVE FRONT WHEEL OPENING EXTENSION PAD RH
REMOVE NO. 3 ENGINE UNDER COVER
REMOVE NO. 1 ENGINE UNDER COVER
DRAIN ENGINE COOLANT
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Note
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
REMOVE BATTERY
for 2WD: Click here
for AWD: Click here
REMOVE FRONT BUMPER COVER
REMOVE HOOD LOCK CONTROL CABLE COVER
for LHD: Click here
for RHD: Click here
REMOVE HOOD LOCK RELEASE LEVER PROTECTOR
REMOVE HOOD LOCK ASSEMBLY
REMOVE INLET AIR CLEANER ASSEMBLY
REMOVE UPPER RADIATOR SUPPORT SUB-ASSEMBLY
w/ Smog Ventilation Sensor:
Disconnect the smog ventilation sensor connector.
for LHD:
Disengage the 4 clamps and disconnect the wire harness from the upper radiator support sub-assembly.
for RHD:
Disengage the 5 clamps and disconnect the wire harness from the upper radiator support sub-assembly.
Remove the 7 bolts and upper radiator support sub-assembly.
DISCONNECT NO. 1 RADIATOR HOSE
Slide the clip and disconnect the No. 1 radiator hose.
DISCONNECT NO. 2 RADIATOR HOSE
Disengage the clamp and disconnect the No. 2 radiator hose from the fan shroud assembly.
Slide the clip and disconnect the No. 2 radiator hose.
DISCONNECT INLET NO. 1 OIL COOLER HOSE
Disengage the clamp to disconnect the inlet No. 1 oil cooler hose from the fan shroud assembly.
Slide the clip and disconnect the inlet No. 1 oil cooler hose.
DISCONNECT OUTLET NO. 1 OIL COOLER HOSE
Slide the clip and disconnect the outlet No. 1 oil cooler hose.
REMOVE RADIATOR ASSEMBLY
Disengage the 2 claws.
Disengage the 2 guides to separate the cooler condenser assembly from the radiator assembly.
Note
Make sure not to damage the cooler condenser assembly when removing the radiator assembly.
Disconnect the cooling fan ECU connector.
Disengage the 4 wire harness clamps.
Remove the radiator assembly with the fan shroud assembly from the vehicle body.
Note
Do not apply excessive force to the cooler condenser assembly or pipe when removing the radiator assembly with the fan shroud assembly.
Disconnect the radiator reserve tank hose from the radiator assembly.
Disengage the 3 claws.
Disengage the 3 guides to remove the fan shroud assembly from the radiator assembly.
Note
Do not damage the radiator assembly when removing the fan shroud assembly.
REMOVE RADIATOR SUPPORT CUSHION
Remove the 2 radiator support cushions from the radiator assembly.
REMOVE LOWER RADIATOR SUPPORT
Remove the 2 lower radiator supports from the radiator assembly.