FRONT SEAT ASSEMBLY INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:


  • Be sure to read Precaution thoroughly before servicing.

    Click here

  • Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The following procedure is for the LH side.

PROCEDURE


  1. INSTALL FRONT SEAT ASSEMBLY


    1. B007X5J

      Place the front seat assembly in the cabin.

      Note

      Be careful not to damage the vehicle body.

    2. Connect the front seat airbag assembly connector under the front seat assembly.


      1. Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

        B007XOAC01
        *a Correct *b Incorrect
        *c Yellow CPA - -
      2. Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

        Note


        • When connecting any airbag connector, take care not to damage the airbag wire harness.


        • When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the yellow CPA, as it may result in an insecure fit.

    3. Connect each connector and engage each clamp under the front seat assembly.

    4. Connect the cable to the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

      Click here

    5. Temporarily install the front seat assembly with the 4 bolts.

    6. Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.

    7. B007YEMN01

      Tighten the 2 bolts on the front side of the front seat assembly.

      Torque:
      36.7 N*m  { 374 kgf*cm, 27 ft.*lbf }

      Note

      Tighten the bolts in the order shown in the illustration.

    8. Operate the slide and vertical power seat switch knob and move the front seat assembly to the foremost position.

    9. B007WRBN01

      Tighten the 2 bolts on the rear side of the front seat assembly.

      Torque:
      36.7 N*m  { 374 kgf*cm, 27 ft.*lbf }

      Note

      Tighten the bolts in the order shown in the illustration.

  2. INSTALL REAR INNER SEAT TRACK BRACKET COVER


    1. B007XLC

      Engage the 2 claws to install the rear inner seat track bracket cover.

  3. INSTALL REAR OUTER SEAT TRACK BRACKET COVER


    1. B007XQD

      Engage the 2 claws to install the rear outer seat track bracket cover.

  4. INSTALL FRONT INNER SEAT TRACK BRACKET COVER


    1. Operate the slide and vertical power seat switch knob and move the front seat assembly to the rearmost position.

    2. B007ZSK

      Engage the 2 claws to install the front inner seat track bracket cover.

  5. INSTALL FRONT OUTER SEAT TRACK BRACKET COVER


    1. B007ZS5

      Engage the 2 claws to install the front outer seat track bracket cover.

  6. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. Install the front seat headrest assembly to the front seat assembly.

  7. INSTALL TELEVISION DISPLAY ASSEMBLY (w/ Rear Seat Entertainment System)

    Click here

  8. INITIALIZATION OF SEAT ECU (w/ Seat Position Memory System)

    Click here

  9. INSPECT FRONT SEAT ASSEMBLY (w/o Seat Position Memory System)

    Click here

  10. INSPECT FRONT SEAT ASSEMBLY (w/ Seat Position Memory System)

    Click here

  11. CHECK SEAT HEATER (w/ Seat Heater System)

    Click here

  12. INSPECT CLIMATE CONTROL SEAT SYSTEM (w/ Climate Control Seat System)

    Click here

  13. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  14. PERFORM ZERO POINT CALIBRATION AND SENSITIVITY CHECK (for Front Passenger Side with Occupant Classification System)

    Click here